LibreELEC (Leia) 9.2.3

Quote from popcornmix

I've found an issue with over_voltage=4 (or higher) on Pi2.
Can you test this firmware
Unzip and replace http://start.elf/fixup.dat on boot partition with start_x.elf/fixup_x.dat from zip file.
Let me know if over_voltage=4 starts to work again.

Hi just tested,replaced firmware and can confirm I can now set over_voltage=4 or higher..but had to remove "_x" from firmware file names otherwise it didn't boot.Thanks.

Wifi speed is very slow with Pi4 9.2.3

I just wanted to say thank you to the LibreELEC team for this release.

Regards,

Shedrock

Quote from Marciano

how about tearing in the menu’s etc?

I never had tearing in any Kodi menu's... since I updated my RPi4 to 9.2.3... Now I have enormous tearing in menus.

But I dont complain, I can live with it.

Wifi Internet Speed in 2,4 Ghz is very slow 0,4 - 6,64 Mbps

Wifi Internet Speed in 5 Ghz is fast 29 - 33 Mbps but why?

Can i set it in Setting to use only 5GHz?

Quote from pauljw

As this is NOT the area to gripe about issues, I'd just like to thank everyone responsible for this software. The update went flawlessly on both my NUC and Rpi3B setups.

Just amazing software, what it does for a Pi is incredible.

Quote from Mario77

Hi Dennis

If you'r overvolting set it to over_voltage=3 or lower and it should boot up normally.

Mario77: I've had already changed the overlocking and voltage to normal and no issues... I will check if I can reset the overclocking and set the over_voltage to 3...

Thanks!!!

Quote from nhhfffvv

Wifi Internet Speed in 2,4 Ghz is very slow 0,4 - 6,64 Mbps

Wifi Internet Speed in 5 Ghz is fast 29 - 33 Mbps but why?

Can i set it in Setting to use only 5GHz?

My normal solution for this is to give my 2.4 and 5GHz WiFi networks different names.

Strange:

After the 9.2.3 update I've got

the

"pulse-eight cec adapter" notification stuck on screen.

Always there.

Any idea on how to disable it ?

Hello @ all,

at first i wanna thank all devs for this great software.

But for all ppl willing to update to 9.2.3:

Make a backup before updading. I ran into a black screen after boot.

Created a thread in support for this.

Best regards,

Horstworst

i have the same Problem on Rpi 3 update from 9.0.2 to 9.2.3

i try 2 time on Clean SD with LibreELEC.USB-SD.Creator not working

and 2 from Online Update not working

so i go back to 9.0.2 and no Problem don´t Update i have lose all my Setting and Data

hello, my english is very bad, speak spanish. Tengo problemas al instalar esta version para actualzar libreelec, me da el error de panic noapic y se frena la instalacion, error de muchas instalciones de linux, que tengo que editar y modificar en el usb para que lo instale

mi pc es un amd64 y una grafica radeon r9 270x

por favor hay alguna solucion a este problema

gracias

Quote from Mggbgz

Wifi speed is very slow with Pi4 9.2.3

Hi mate, i have the same problem and I have made the conclusion that raspberry pi 4 is working better with 5ghz connection, I have a router that supports only 2.4ghz and I am looking to buy another one with 5ghz to have better connection so you have that problem because your router doesn't support 5ghz i think (sorry for the wrong thread but I wanted to help in this problem )

Hello.

I'm having an issue with versions +9. Any 9.x gives me this error.

And it didn't happen with 8.x or 7.x.

My PC has an Athlon 3500+ and Radeon R9 270X.

What can I do to install it?

Quote from robdanmar

Hello.

I'm having an issue with versions +9. Any 9.x gives me this error.

And it didn't happen with 8.x or 7.x.

My PC has an Athlon 3500+ and Radeon R9 270X.

What can I do to install it?

Read: LibreELEC (Leia) 9.2.3

Please do not post errors issues in "News and Announcements" section...

Can someone confirm that analog out on Rpi3B+ does not work anymore? In some older Libreelec (I do not know now the version) it worked normally but in 9.2.3 not.

Of course, in system is selected "Analog out".