Hello, I'm loosing my wifi connection. It's a bit similar to this old issue I think. I'm still connected but I got no connection. If I download or stream I loose the connection faster. No freeze. Ethernet works.
I did not have this issue with LibreELEC-S905.arm-8.2-8.2.3.1, I got an s905x tanix3pro. I hope this was not already discussed but I could not find any post related.
Need to know which wifi chipset you have and a copy of your dmesg after the wifi dies.
Hi!
I have player X96 S905x (1Gb/8Gb)
The remote control on all previous releases worked perfectly, using the file "remote.conf".
This file I put in the folder "\storage\.config"
This is the same remote control I also adapted to control the player "Raspberry Pi 3 + Libreelec" using a file "lircd.conf".
This file I also put in the folder "\storage\.config"
- The files I put in the folder by simply copying from a USB drive.
Everything worked fine until the new version 8.90.4.
The question is simple: What file and in what folder I have to put (copy) that to make this my remote control work on the new version 8.90.4.
Files "remote.conf" and "lircd.conf" his remote control attached - RC_X96&RPi3.zip
I see why it's not working for my. It only works with the original remote.
So now you have the scan codes, all you have to do is follow the instructions on creating your own keymap.
See these two posts:
Got it working, will soon post my remote (which is the remote of the Mecool) and the config.
Hello,
What are the different resolutions supported in this version. I have a 2560x1440 Asus monitor.
Thank you in advance.
Reboot from nand doesn't work for me either.
Is there a changelog for this build?
That's your kodi log not dmesg
And that's the Wi-Fi band not the chipset
Any hints to get Astrometa DVB-stick (MN88473/RTL2832) to work in 8.90.4? I have installed Tvheadend 4.2 and CrazyCat drivers. The stick is found and available in Tvheadend. Scan does find only a few channels and trying to watch them gives a myriad of "Continuity counter errors". Stick works fine in RPi with Libreelec 7.0.3 (but not in 8.2.3 as well known).
I also tried Tvheadend 4.3 in 8.90.4, but cannot connect to the server for some reason?
Is there a changelog for this build?
No changelog For alpha versions.
Now I'm *ucked up 
device: Beelink Mini MXIII II
dtb used: gxl_p212_2g_nand.dtb (newest from here)
Install location: internal since beginnig (libreelec 8.0)
8.90.3 everything runs well like 50 updates before
Now 8.90.4 update, stuck at boot after installation, no contact via ssh possible.
PLEASE HELP
I have configured my remote to the last version but I have problems with the delay of the key press.
It's going too fast. Navigating from the menus a single click is detected like long press.
huge delay like
ir-keytable -D 5000 -P 100
Also not helps.
The remote is using nec protocol.
Any clue?
Display MoreNow I'm *ucked up
device: Beelink Mini MXIII II
dtb used: gxl_p212_2g_nand.dtb (newest from here)
Install location: internal since beginnig (libreelec 8.0)
8.90.3 everything runs well like 50 updates beforeNow 8.90.4 update, stuck at boot after installation, no contact via ssh possible.
PLEASE HELP
you need another sd card to boot le, then try to change dtb from there.
But dtb is the right one. I don't know why 8.90.4 killed my device
But dtb is the right one. I don't know why 8.90.4 killed my device
Stuck on LE screen or bootloader screen?
bootloader screen
remote not working for me
Mecool M8S L.
Nothing to do with update, dropped it in a pint of pop!
