There are same rules as for kszaq's builds. For S905 is necessary to replace dtb.img with corresponding dtb.
So it is necessary ro Switch the dtb file? Do i have to rename the dtb file to dtb.img? Could this be the Problem for not booting into the Flash Screen?
So it is necessary ro Switch the dtb file? Do i have to rename the dtb file to dtb.img? Could this be the Problem for not booting into the Flash Screen?
Yes. Yes. Yes.
Tested on Nexbox A95X S905X (2g/16g):
- boot from SD card --- ok
- install to NAND using ssh script from SD card -- ok
- CEC, Wifi 2.4/5 ghz, bluetooth, lan, dvb-t2 Mygica T203 -- all okSo far so good.
Thanks kszaq.
Hi,
I am getting error ---------cannot mount /dev/mmcblk0p1 .....any idea ? Doing it on A95X 2gb/16gb using micro SD card....Thanks in advance
ohh 7.0.2.008 is released!! downloading now.
Hi,
I did exactly as you recommended:
For burning the SD I used OSX, so I got everything right and it worked.
Only Problem I have, I can't copy the dtb.img for S905 on to the SD, because its not accessable when I put the SD in the Macbook.
pls advise
Hi,I did exactly as you recommended:
For burning the SD I used OSX, so I got everything right and it worked.
Only Problem I have, I can't copy the dtb.img for S905 on to the SD, because its not accessable when I put the SD in the Macbook.
pls advise
Okay !
My mind reading skills are getting better but they are not 100%
You used Mac OSX to burn image to SD card and it worked ? Worked how ?
Can't copy device tree because your sd card wont mount ?
Is your card named BOOT on your desktop ?
What did you use to burn the image in OSX ? You say I got everything right and it worked.
I use Mac OSX and can help you if we can get on the same planet. 
Give me exact steps you have taken.
Okay !
My mind reading skills are getting better but they are not 100%
You used Mac OSX to burn image to SD card and it worked ? Worked how ?
Can't copy device tree because your sd card wont mount ?
Is your card named BOOT on your desktop ?
What did you use to burn the image in OSX ? You say I got everything right and it worked.
I use Mac OSX and can help you if we can get on the same planet.
Give me exact steps you have taken.
ok,
I have a NexBox A95X with a S905 an 1GB / 8GB and Wifi.
I downloaded the files from here: 7.0.2.007
I used this OSX Installation-Procedure Installation - LibreELEC
SD card/USB drive:
Note: only 1 USB port is able to boot the box. You have to try them all.
I have not received any errors from the OSX Terminal.
Somehow never the less it did not seem to go right. I cant get the renamed dbt.img, cause the SD wont mount!
I have tried it on a Linux-System with the same result.
LibreELEC-S905.aarch64-8.0-devel-20161014142818-r0001.img.gz
- VP9 HW decoding for S905X
LibreELEC-S905.aarch64-8.0-devel-20161014142818-r0001.img.gz
- VP9 HW decoding for S905X
Just tested your build. Not only playback of 4K VP9 video is working but also 4K H264. Minor stuttering was noticeable when playback of 'The Curvature of Earth', other than that playback was fine.
Thanks so much for sharing your build.
I have not received any errors from the OSX Terminal.Somehow never the less it did not seem to go right. I cant get the renamed dbt.img, cause the SD wont mount!
I have tried it on a Linux-System with the same result.
Can you go to #573
I had a real long posting session with another member back then and he got it in the end.
Start reading from that post regarding using ApplePi-Baker to burn images to sd card.
That is what i use, as Terminal in OSX has given me problems in the past.
The fact that your SD card did not mount after terminal commands suggests it did not work.
Hello,
I install this image to a USB and it boot well.
The only problem I have is that I can not connect more USB devices as keyboard of remote receiver.
I have some questions:
1. Is it secure to install to NAND? Could I donwload the Android firmware? I have a Beelink Mini III
2. If I install to NAND, could get updates?
I really apreciate your work.
Thanks and best regards.
Hello,I install this image to a USB and it boot well.
The only problem I have is that I can not connect more USB devices as keyboard of remote receiver.
I have some questions:
1. Is it secure to install to NAND? Could I donwload the Android firmware? I have a Beelink Mini III
2. If I install to NAND, could get updates?
I really apreciate your work.
Thanks and best regards.
Try a hub, or install to a microsd card. Personally, I want to keep android, just in case
Try a hub, or install to a microsd card. Personally, I want to keep android, just in case
Thanks!
I installed to internal (installtointernal command) and it really boot well now with USB keyboard pluged.
Kind regards.
2. If I install to NAND, could get updates?
Covered this on LE updates OTA. Link above.
Hi again, found time to conect ftdi and try newest image but nothing new 
here is bootlog
U-Boot 2015.01-ga9e9562-dirty (Apr 28 2016 - 14:31:08)
DRAM: 1 GiB
Relocation Offset is: 36ed4000
register usb cfg[0][1] = 0000000037f62830
register usb cfg[0][2] = 0000000037f62850
register usb cfg[2][0] = 0000000037f62870
vpu detect type: 5
vpu clk_level = 7
set vpu clk: 666667000Hz, readback: 666660000Hz(0x300)
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=8, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC: aml_priv->desc_buf = 0x0000000033ec4770
aml_priv->desc_buf = 0x0000000033ec6900
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
[mmc_init] mmc init success
mmc read lba=0x14000, blocks=0x400
start dts,buffer=0000000033ec8ff0,dt_addr=0000000033ec8ff0
parts: 11
00: logo 0000000002000000 1
01: recovery 0000000002000000 1
02: rsv 0000000000800000 1
03: tee 0000000000800000 1
04: crypt 0000000002000000 1
05: misc 0000000002000000 1
06: instaboot 0000000020000000 1
07: boot 0000000002000000 1
08: system 0000000040000000 1
09: cache 0000000020000000 2
10: data ffffffffffffffff 4
get_dtb_struct: Get emmc dtb OK!
overide_emmc_partition_table: overide cache
[mmc_get_partition_table] skip partition cache.
Partition table get from SPL is :
name offset size flag
================================================================================ ===
0: bootloader 0 400000 0
1: reserved 2400000 4000000 0
2: cache 6c00000 20000000 2
3: env 27400000 800000 0
4: logo 28400000 2000000 1
5: recovery 2ac00000 2000000 1
6: rsv 2d400000 800000 1
7: tee 2e400000 800000 1
8: crypt 2f400000 2000000 1
9: misc 31c00000 2000000 1
10: instaboot 34400000 20000000 1
11: boot 54c00000 2000000 1
12: system 57400000 40000000 1
13: data 97c00000 136500000 4
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
Net: Meson_Ethernet
wipe_data=successful
wipe_cache=successful
upgrade_step=0
reboot_mode=cold_boot
hpd_state=0
[CANVAS]addr=0x3f800000 width=3840, height=2160
Not find '576cvbs' mapped VIC
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[KM]Error:f[key_manage_query_size]L504:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L504:key[deviceid] not programed yet
gpio: pin GPIOAO_3 (gpio 122) value is 1
saradc - saradc sub-system
Usage:
saradc saradc open <channel> - open a SARADC channel
saradc close - close the SARADC
saradc getval - get the value in current channel
saradc get_in_range <min> <max> - return 0 if current value in the range of curr ent channel
Enter USB burn
Try connect time out 701, 700, 647
Hit any key to stop autoboot: 0
ret = 1 .[mmc_init] mmc init success
Device: SDIO Port B
Manufacturer ID: 1b
OEM: 534d
Name: 00000
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: No
Capacity: 1.9 GiB
Bus Width: 4-bit
reading kernel.img
8790016 bytes read in 708 ms (11.8 MiB/s)
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
libfdt fdt_setprop(): FDT_ERR_NOSPACE
libfdt fdt_path_offset() returned FDT_ERR_NOTFOUND
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =33f491c0
copy done
load dtb from 0x1000000 ......
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x01c36ee0
reserving fdt memory region: addr=1000000 size=8000
Loading Ramdisk to 33bfe000, end 33ec1a0e ... OK
Loading Device Tree to 000000001fff5000, end 000000001fffffff ... OK
signature:
fdt_instaboot: get header err
Starting kernel ...
uboot time: 3585254 us
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Linux version 3.14.29 (kszaq@FPGAWorker) (gcc version 5.3.0 (GC C) ) #1 SMP Fri Oct 14 09:00:25 CEST 2016
[ 0.000000@0] CPU: AArch64 Processor [410fd034] revision 4
[ 0.000000@0] no prop version_code
[ 0.000000@0] bootconsole [earlycon0] enabled
[ 0.000000@0] fdt Reserved memory table:
[ 0.000000@0] linux,meson-fb: 0x000000003bb80000 - 0x0000000040000 000 (68 MiB)
[ 0.000000@0] linux,di: 0x0000000039d80000 - 0x000000003bb80 000 (30 MiB)
[ 0.000000@0] DI: DI reserved memory: created CMA memory pool at 0x0000000039 d80000, size 30 MiB
[ 0.000000@0] linux,ion-dev: 0x0000000037d80000 - 0x0000000039d80 000 (32 MiB)
[ 0.000000@0] linux,codec_mm_cma: 0x0000000027800000 - 0x0000000033800 000 (192 MiB)
[ 0.000000@0] linux,picdec: 0x0000000034c00000 - 0x0000000037c00 000 (48 MiB)
[ 0.000000@0] linux,codec_mm_reserved: 0x0000000023700000 - 0x0000000027800 000 (65 MiB)
[ 0.000000@0] fdt Reserved memory total: 470 MiB
[ 0.000000@0] cma: Reserved 8 MiB at 34400000
[ 0.000000@0] psci: probing function IDs from device-tree
[ 0.000000@0] PERCPU: Embedded 12 pages/cpu @ffffffc037d2c000 s17792 r8192 d2 3168 u49152
[ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total p ages: 227324
[ 0.000000@0] Kernel command line: rootfstype=ramfs init=/init console=ttyS0, 115200 no_console_suspend earlyprintk=aml-uart,0xc81004c0 ramoops.mem_address=0x 20000000 ramoops.mem_size=0x100000 ramoops.record_size=0x8000 ramoops.console_si ze=0x4000 androidboot.selinux=permissive logo=osd1,loaded,0x3f800000,576cvbs hdm imode=1080p60hz cvbsmode=576cvbs hdmitx= androidboot.firstboot=1 mac=c4:2f:11:18 :26:e1 androidboot.mac=c4:2f:11:18:26:e1 BOOT_IMAGE=kernel.img boot=/dev/mmcblk0 p1 disk=/dev/mmcblk0p2 console=tty0 systemd.show_status=auto
[ 0.000000@0] logo: osd1
[ 0.000000@0] logo: loaded
[ 0.000000@0] logo: 0x3f800000
[ 0.000000@0] logo: 576cvbs
[ 0.000000@0] vout_serve: 1080p60hz
[ 0.000000@0] vout_serve: en: 1
[ 0.000000@0] logo: get hdmimode: 1080p60hz
[ 0.000000@0] logo: get cvbsmode: 576cvbs
[ 0.000000@0] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000@0] Dentry cache hash table entries: 131072 (order: 8, 1048576 byte s)
[ 0.000000@0] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.000000@0] Memory: 499676K/926208K available (7504K kernel code, 747K rwda ta, 2860K rodata, 873K init, 5213K bss, 426532K reserved)
[ 0.000000@0] Virtual kernel memory layout:
[ 0.000000@0] vmalloc : 0xffffff8000000000 - 0xffffff8040000000 ( 1024 MB)
[ 0.000000@0] vmemmap : 0xffffff8040010000 - 0xffffff80410dbc00 ( 16 MB)
[ 0.000000@0] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
[ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc03bb80000 ( 955 MB)
[ 0.000000@0] .init : 0xffffffc001aa1000 - 0xffffffc001b7b580 ( 874 kB)
[ 0.000000@0] .text : 0xffffffc001080000 - 0xffffffc001aa0354 ( 10369 kB)
[ 0.000000@0] .data : 0xffffffc001b7c000 - 0xffffffc001c36ee0 ( 748 kB)
[ 0.000000@0] PM: Registered nosave memory: [mem 0x01080000-0x01a9ffff]
[ 0.000000@0] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000@0] arch_multi_cluster:0
[ 0.000000@0] Hierarchical RCU implementation.
[ 0.000000@0] RCU debugfs-based tracing is enabled.
[ 0.000000@0] CONFIG_RCU_FANOUT set to non-default value of 32
[ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
[ 0.000000@0] clocksource_of_init: no matching clocksources found
[ 0.000000@0] Kernel panic - not syncing: Unable to initialise architected ti mer.
[ 0.000000@0]
[ 0.000000@0] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.14.29 #1
[ 0.000000@0] Call trace:
[ 0.000000@0] [<ffffffc001087a78>] dump_backtrace+0x0/0x130
[ 0.000000@0] [<ffffffc001087bc8>] show_stack+0x20/0x30
[ 0.000000@0] [<ffffffc0017c383c>] dump_stack+0x78/0x94
[ 0.000000@0] [<ffffffc0017c2ad4>] panic+0xd8/0x1fc
[ 0.000000@0] [<ffffffc001aa3898>] time_init+0x1c/0x38
[ 0.000000@0] [<ffffffc001aa16b4>] start_kernel+0x204/0x344
LibreELEC-S905.aarch64-8.0-devel-20161014142818-r0001.img.gz
- VP9 HW decoding for S905X
good job, waiting for the next updates.
Hello,
I have this image (007) and it works great with tvheadend client.
The only problem is with the remote. The original remote doesn't work. I use othe USB receiver and it works great. I can switch off but not switch on.
I try to switch on with the original remote but nothing.
Is there any way to power on or resume with a external USB receiver?
Best regards.
Can you go to #573
I had a real long posting session with another member back then and he got it in the end.Start reading from that post regarding using ApplePi-Baker to burn images to sd card.
That is what i use, as Terminal in OSX has given me problems in the past.
The fact that your SD card did not mount after terminal commands suggests it did not work.
ApplePI-Baker did the Job!
many thx!
gretsch61