Try to connect via SSH and get the list of modules that you are using (lsmod).
Here's the output:
Module Size Used by
dhd 658858 0
btsdio 2434 0
bluetooth 193132 1 btsdio
8021q 16201 0
hid_logitech_dj 9603 0
wifi_dummy 745 0
mali 161003 5Here's the relevant dmesg dumps if it helps:
[ 30.948199@2] Bluetooth: HCI device and connection manager initialized
[ 30.948218@2] Bluetooth: HCI socket layer initialized
[ 30.948225@2] Bluetooth: L2CAP socket layer initialized
[ 30.948240@2] Bluetooth: SCO socket layer initialized
[ 30.950517@2] Bluetooth: Generic Bluetooth SDIO driver ver 0.1
[ 30.955104@0] dhd_module_init: in
[ 30.955112@0] wifi_setup_dt
[ 30.955117@0] wifi_request_32k_clk : ON-->ON for sdio_wifi
[ 30.955121@0] interrupt_pin(133) : sdio_wifi
[ 30.955126@0] sdio_wifi is using the pin GPIOX_21
[ 30.955129@0] wifi_dt : gpio op failed(-16) at line 210
[ 30.955138@0] reg:2620,clearmask=100010,setmask=0
[ 30.955142@0] reg:2622,clearmask=ff,set pin=133
[ 30.955146@0] reg:2623,clearmask=70000,setmask=4
[ 30.955149@0] interrupt_pin(133) : sdio_wifi
[ 30.955152@0] power_on_pin(6) : sdio_wifi
[ 30.955155@0] sdio_wifi is using the pin GPIOAO_6
[ 30.955158@0] wifi_dt : gpio op failed(-16) at line 232
[ 30.955162@0] power_on_pin(6) : sdio_wifi
[ 30.955165@0] power_on_pin2(123) : sdio_wifi
[ 30.955169@0] sdio_wifi is using the pin GPIOX_11
[ 30.955171@0] wifi_dt : gpio op failed(-16) at line 244
[ 30.955175@0] power_on_pin2(123) : sdio_wifi
[ 30.955179@0] ======== bcm_wlan_set_plat_data ========
[ 30.955184@0] host_oob_irq: 100
[ 30.955188@0] host_oob_irq_flags=1044
[ 30.955191@0] dhd_wifi_platform_load: Enter
[ 30.955202@0] Power-up adapter 'DHD generic adapter'
[ 30.955205@0] wifi_platform_set_power = 1
[ 30.955208@0] ======== PULL WL_REG_ON HIGH! ========
[ 30.955212@0] WIFI Disable! 6
[ 31.014431@2] [aml-spdif-dai]enterd aml_spdif_play,set_clock:5,sample_rate=4
[ 31.014440@2] audio_set_958_clk, freq=4,
[ 31.014449@2] IEC958 16bit
[ 31.014454@2] hdmitx: audio: aout notify rate 48000
[ 31.014457@2] hdmitx: audio: aout notify size 16
[ 31.014463@2] aml_i2s_close device type 8
[ 31.155024@0] WIFI Enable! 6
[ 31.663260@0] wifi_platform_bus_enumerate device present 1
[ 31.663272@0] ======== Card detection to detect SDIO card! ========
[ 31.663280@0] sdio_reset_comm():
[ 33.823282@2] btsdio: probe of sdio:0001:3 failed with error -110
[ 33.837281@2] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 33.839026@2] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 33.840763@2] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 33.843895@2] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 33.905139@2] [sdio_reinit] finish
[ 33.905156@3] [sdio_reinit] finish
[ 33.992312@2] bcmsdh_register: register client driver
[ 33.992371@2] bcmsdh_sdmmc: bcmsdh_sdmmc_probe Enter
[ 33.992626@2] bcmsdh_sdmmc: bcmsdh_sdmmc_probe Enter
[ 33.992632@2] bus num (host idx)=1, slot num (rca)=1
[ 33.992636@2] found adapter info 'DHD generic adapter'
[ 33.992642@2] 7 bcmdhd_mem_prealloc: wlan_mem_array[section].mem_ptr=c09a95d8, size=139264
[ 33.992646@2] success alloc section 3, size 139264
[ 33.992729@2] alloc static buf at edf40000!
[ 33.992733@2] 1 bcmdhd_mem_prealloc: section=4, wlan_static_skb=c0be11e4
[ 33.992736@2] success alloc section 4, size 0
[ 33.992972@2] dhdsdio_probe : no mutex held. set lock
[ 33.993044@2] F1 signature read @0x18000000=0x16224335
[ 33.995245@2] F1 signature OK, socitype:0x1 chip:0x4339 rev:0x1 pkg:0x2
[ 33.995601@2] DHD: dongle ram size is set to 786432(orig 786432) at 0x180000
[ 33.995642@2] 4 bcmdhd_mem_prealloc: section=7, wlan_mem_array[4]=edf20000
[ 33.995645@2] success alloc section 7, size 19744
[ 33.995669@2] dhd_conf_set_chiprev: chip=0x4339, chiprev=1
[ 33.995702@2] dhd_conf_set_conf_path_by_nv_path: config_path=/lib/firmware/brcm/config.txt
[ 33.996977@2] dhd_conf_read_nv_by_chip: nv_by_chip_count=9
[ 33.996986@2] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=0, name=nvram_ap6181.txt
[ 33.996991@2] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 33.996995@2] dhd_conf_read_nv_by_chip: chip=0xa9a6, chiprev=0, name=nvram_ap6212.txt
[ 33.996999@2] dhd_conf_read_nv_by_chip: chip=0xa9a6, chiprev=1, name=nvram_ap6212a.txt
[ 33.997002@2] dhd_conf_read_nv_by_chip: chip=0x4345, chiprev=6, name=nvram_ap6255.txt
[ 33.997006@2] dhd_conf_read_nv_by_chip: chip=0x4330, chiprev=4, name=nvram_ap6330.txt
[ 33.997010@2] dhd_conf_read_nv_by_chip: chip=0x4339, chiprev=1, name=nvram_ap6335.txt
[ 33.997014@2] dhd_conf_read_nv_by_chip: chip=0x4356, chiprev=2, name=nvram_ap6356.txt
[ 33.997018@2] dhd_conf_read_nv_by_chip: chip=0x4335, chiprev=1, name=nvram_bcm4335.txt
[ 33.997042@2] dhd_conf_read_config: mimo_bw_cap = 1
[ 33.997186@2] dhd_conf_read_config: bcn_timeout = 20
[ 33.997222@2] dhd_conf_read_config: kso_enable = 0
[ 33.997336@2] dhd_conf_read_config: PM = 0
[ 33.997374@2] 7 bcmdhd_mem_prealloc: wlan_mem_array[section].mem_ptr=c09a95c0, size=10416
[ 33.997377@2] success alloc section 0, size 10416
[ 33.997659@2] 2 bcmdhd_mem_prealloc: section=5, wlan_static_scan_buf0=edf30000
[ 33.997664@2] success alloc section 5, size 65536
[ 33.997935@2] wl_create_event_handler(): thread:wl_event_handler:93b started
[ 33.997939@1] tsk Enter, tsk = 0xedf9669c
[ 33.998264@2] dhd_attach(): thread:dhd_watchdog_thread:93d started
[ 33.998292@2] dhd_attach(): thread:dhd_dpc:93e started
[ 33.998300@0] dhd_dpc_thread: set dpc_cpucore 0 from config.txt
[ 33.998316@2] dhd_attach(): thread:dhd_rxf:93f started
[ 33.998327@2] dhd_deferred_work_init: work queue initialized
[ 33.998335@2] 7 bcmdhd_mem_prealloc: wlan_mem_array[section].mem_ptr=c09a95c8, size=10396
[ 33.998338@2] success alloc section 1, size 10396
[ 33.998348@2] 7 bcmdhd_mem_prealloc: wlan_mem_array[section].mem_ptr=c09a95d0, size=65536
[ 33.998351@2] success alloc section 2, size 65536
[ 33.998517@2] dhdsdio_probe_init: set use_rxchain 1 from config.txt
[ 34.005839@2] Dongle Host Driver, version 1.201.59.5 (r506368)
[ 34.005839@2] Compiled in drivers/net/wireless/bcmdhd
[ 34.006185@2] Register interface [wlan0] MAC: 94:a1:a2:48:e7:7b
[ 34.006185@2]
[ 34.006193@2] dhd_prot_ioctl : bus is down. we have nothing to do
[ 34.006231@2] bcmsdh_oob_intr_unregister: Enter
[ 34.006235@2] bcmsdh_oob_intr_unregister: irq is not registered
[ 34.006242@2] dhd_txglom_enable: enable 0
[ 34.006245@2] dhd_bus_devreset: WLAN OFF DONE
[ 34.006286@2] wifi_platform_set_power = 0
[ 34.006289@2] ======== PULL WL_REG_ON LOW! ========
[ 34.006293@2] dhdsdio_probe : the lock is released.
[ 34.006590@0] dhd_open: Enter ef473000
[ 34.006599@0]
[ 34.006599@0] Dongle Host Driver, version 1.201.59.5 (r506368)
[ 34.006599@0] Compiled in drivers/net/wireless/bcmdhd
[ 34.006605@0] wl_android_wifi_on in 1
[ 34.006609@0] wl_android_wifi_on in 2: g_wifi_on=0
[ 34.006612@0] wifi_platform_set_power = 1
[ 34.006615@0] ======== PULL WL_REG_ON HIGH! ========
[ 34.006623@0] WIFI Disable! 6
[ 34.013295@2] dhd_module_init: Exit err=0
[ 34.206431@0] WIFI Enable! 6
[ 34.713229@0] sdio_reset_comm():
[ 34.727076@2] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 34.795378@2]
[ 34.795378@2]
[ 34.795378@2] dhd_bus_devreset: == WLAN ON ==
[ 34.795455@2] F1 signature read @0x18000000=0x16224335
[ 34.797613@2] F1 signature OK, socitype:0x1 chip:0x4339 rev:0x1 pkg:0x2
[ 34.797970@2] DHD: dongle ram size is set to 786432(orig 786432) at 0x180000
[ 34.798116@2] dhdsdio_probe_init: set use_rxchain 1 from config.txt
[ 34.798331@2] dhd_conf_read_nv_by_chip: nv_by_chip_count=9
[ 34.798337@2] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=0, name=nvram_ap6181.txt
[ 34.798342@2] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 34.798346@2] dhd_conf_read_nv_by_chip: chip=0xa9a6, chiprev=0, name=nvram_ap6212.txt
[ 34.798349@2] dhd_conf_read_nv_by_chip: chip=0xa9a6, chiprev=1, name=nvram_ap6212a.txt
[ 34.798353@2] dhd_conf_read_nv_by_chip: chip=0x4345, chiprev=6, name=nvram_ap6255.txt
[ 34.798357@2] dhd_conf_read_nv_by_chip: chip=0x4330, chiprev=4, name=nvram_ap6330.txt
[ 34.798361@2] dhd_conf_read_nv_by_chip: chip=0x4339, chiprev=1, name=nvram_ap6335.txt
[ 34.798365@2] dhd_conf_read_nv_by_chip: chip=0x4356, chiprev=2, name=nvram_ap6356.txt
[ 34.798369@2] dhd_conf_read_nv_by_chip: chip=0x4335, chiprev=1, name=nvram_bcm4335.txt
[ 34.798392@2] dhd_conf_read_config: mimo_bw_cap = 1
[ 34.798536@2] dhd_conf_read_config: bcn_timeout = 20
[ 34.798573@2] dhd_conf_read_config: kso_enable = 0
[ 34.798686@2] dhd_conf_read_config: PM = 0
[ 34.798705@2] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm4339a0_ag.bin
[ 34.798709@2] dhd_conf_set_nv_name_by_chip: nvram_path=/lib/firmware/brcm/nvram_ap6335.txt
[ 34.798712@2] Final fw_path=/lib/firmware/brcm/fw_bcm4339a0_ag.bin
[ 34.798715@2] Final nv_path=/lib/firmware/brcm/nvram_ap6335.txt
[ 34.798718@2] Final conf_path=/lib/firmware/brcm/config.txt
[ 30.873259@2] [aml_sdio_print_err] sdio: Timeout error, Cmd8 arg 0x1aa, Xfer 0 Bytes, host->xfer_step=12, host->cmd_is_stop=0, pdata->port=0, virqs=0x13, virqc=0x1f003f00, conf->cmd_clk_divide=177, pdata->clkc=177, conf->bus_width=0, pdata->width=0, conf=0x416270b1, clock=397940
[ 30.873259@2] [aml_sdio_timeout] time_start_cnt:993
[ 30.873259@2] [aml_sdio_print_err] sdio: Timeout error, Cmd52 arg 0x80062000, Xfer 0 Bytes, host->xfer_step=12, host->cmd_is_stop=0, pdata->port=0, virqs=0x13, virqc=0x1f001f00, conf->cmd_clk_divide=1, pdata->clkc=1, conf->bus_width=1, pdata->width=1, conf=0x41727001, clock=35416666
[ 30.873259@2]
[ 34.953292@2] NVRAM version: AP6335_NVRAM_V1.5_03112014
[ 34.953926@2] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.
[ 35.132282@2] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us)
[ 35.132450@2] bcmsdh_oob_intr_register: Enter
[ 35.132454@2] bcmsdh_oob_intr_register: HW_OOB enabled
[ 35.132458@2] bcmsdh_oob_intr_register OOB irq=100 flags=414
[ 35.132474@2] bcmsdh_oob_intr_register: enable_irq_wake
[ 35.132478@2] bcmsdh_oob_intr_register: enable_irq_wake failed with -6
[ 35.133325@0] dhd_conf_set_band: Set band 0
[ 35.133464@0] dhd_preinit_ioctls: Set tcpack_sup_mode 0
[ 35.142981@0] Firmware up: op_mode=0x0005, MAC=94:a1:a2:48:e7:7b
[ 35.142987@0] dhd_conf_set_country: Set country CN, revision 38
[ 35.189133@0] Country code: CN (CN/38)
[ 35.189355@0] dhd_conf_set_roam: Set roam_off 1
[ 35.191489@0] dhd_conf_set_mimo_bw_cap: Set mimo_bw_cap 1
[ 35.192071@0] dhd_conf_set_txbf: set txbf 1
[ 35.209797@0] Firmware version = wl0: Dec 6 2013 15:47:10 version 6.37.32.RC23.34.10 (r)
[ 35.209809@0] Driver: 1.201.59.5 (r506368)
[ 35.209809@0] Firmware: wl0: Dec 6 2013 15:47:10 version 6.37.32.RC23.34.10 (r)
[ 35.210073@0] dhd_txglom_enable: enable 1
[ 35.210080@0] dhd_conf_set_disable_proptx: set disable_proptx 0
[ 35.210844@0] dhd_wlfc_hostreorder_init(): successful bdcv2 tlv signaling, 64
[ 35.211203@0] wl_android_wifi_on: Success
[ 35.267334@0] dhd_open: Exit ret=0
........<when trying to connect to the network>....
[ 174.753629@0] Connectting with c0:56:27:41:0d:bb channel (11) ssid "Nijia", len (5)
[ 174.753629@0]
[ 174.809604@0] dhdsdio_rxglom (subframe 1): HW hdr error: len/check 0x7365/0x6843
[ 174.809607@0] dhdsdio_rxfail: abort command, terminate frame, send NAK
[ 174.811018@0] dhdsdio_rxglom (superframe): HW hdr error: len/check 0x0000/0x0000
[ 174.811024@0] dhdsdio_rxglom: got unlikely tx max 0 with tx_seq 112
[ 174.811028@0] dhdsdio_rxfail: abort command, terminate frame, send NAK
[ 174.812421@0] dhdsdio_rxglom (superframe): HW hdr error: len/check 0x0000/0x0000
[ 174.812427@0] dhdsdio_rxglom: got unlikely tx max 0 with tx_seq 112
[ 174.812432@0] dhdsdio_rxfail: abort command, terminate frame, send NAK
[ 174.813863@0] dhdsdio_rxglom (superframe): HW hdr error: len/check 0x0000/0x0000
[ 174.813870@0] dhdsdio_rxglom: got unlikely tx max 0 with tx_seq 112
[ 174.813874@0] dhdsdio_rxfail: abort command, terminate frame
[ 174.824334@2] wl_bss_connect_done succeeded with c0:56:27:41:0d:bbJudging from the dmesg log, it seems like it's loading the correct driver?
You need to download and burn to SD card these two file. Next, use the toothpick or use the app "Update&Backup".
Yandex.Disk
Activation multi-boot is possible only with SD card. After activating multi-boot, the system will be able to run images from SD cards and USB flash drives. Please note, the initial activation of the multi-boot is possible ONLY with SD card.
Thanks for the reply. I have tried the toothpick method with only the two "aml_autoscript" files on an sd card from the original image but I still get the Google TV boot loop. I have also tried the V04 files for S812 mentioned above for Stupin with the same result. I am sorry, I am clearly still doing something wrong.
Hello,
I have an MXIII-G 1G/8G with the version 7.0.1c build from kszaq and I would like to update it with your build.
I have tried the version 7.0.2.6 and 8.0 beta without success.
The 7.0.2.6 won't boot and I have an APIPA IP address with the 8.0 build (a fixed IP don't help much as there is no network connectivity)
Someone can help me?
Thanks in advance!
balbes150, thank you for the update. any changelog?
Hi Balbes,
Thanks for the new builds 
But I can't install them through recovery nor by using the Update folder 
If it can help, here are the pics of the board:
Hi balbes150, thanks for the effort! However, it seems that the Wifi problem is still present. To elaborate on the problem, the Wifi goes up allowing pinging and ssh as for a long time, but the moment I start downloading something (like addons), it gets cut off.
Just to check if it's a hardware problem, I flashed the stock android firmware on the device and the wifi worked without any problems. I think I'll try looking around other threads to see what are the possible fixes. Though, any suggestion how to start debugging the thing beyond dmesg and lsmod dumps? I've tried scanning the loaded DTBs but it didn't give me much information.
I will try and report back
But I prefer to install LE on NAND
Krypton:
Many thx for this image, just two things...
4k is not working correctly... GUI is shown only by a quarter of the screen.SQL db connection fails.
After sort of laggy performance on SD card I decided to install on NAND and what a difference. Big thank you for the latest build, even BT works.
To elaborate on the problem, the Wifi goes up allowing pinging and ssh as for a long time, but the moment I start downloading something (like addons), it gets cut off.
This was an issue with Realtek wifi chips.
Not sure how kszaq fixed this issue.
Just mentioning it here because of the identical wifi behaviour.
Is there any chance this s812 build would work with the CX-S806 boxes running Amlogic s812 chips?
They're setup as: 2GB RAM, 8GB NAND, 100-Mbps NIC + WiFi is the standard ?6230? (not the Realtek)
Kerber previously had some builds for this box, labeled 806-812, but eventually stopped releasing them.
Thank you in advance!
It would be nice to update Kodi RC2 and applied updates from LE 7.90.010 
Is there any chance this s812 build would work with the CX-S806 boxes running Amlogic s812 chips?They're setup as: 2GB RAM, 8GB NAND, 100-Mbps NIC + WiFi is the standard ?6230? (not the Realtek)
Kerber previously had some builds for this box, labeled 806-812, but eventually stopped releasing them.
Thank you in advance!
Former Kerber user myself.
I successfully installed LE 7.2.0.6. on my cx-s806 (812 edition) just now.
Wifi and LAN are fine.
Only consideration is that during boot-up the led briefly shines blue, and then turns to red while the device happily continues to boot. I have a youtube movie playing on the CX as I type this ... but the LED stays red. No biggy for me as this box is now my backup, I use a T95x (1/8) as my main rig for VP9 / HDR / 10bit reasons.
I used this file from Balbes work using a thumbdrive and a recovery.img that I extracted from one of Kerber's builds.
Just don't forget to modify "sdcard" to udisk in the aml file, like this :
--update_package=/udisk/LibreELEC-S812.MXIII_Plus.arm-7.0.2.6-update.zip
thank you Balbes, and thank you Kerber
