[7.0.3.012l] LibreELEC 7.0 for S905/S905X


  • Lirc is not used for internal IR receiver. I use amremote in my builds in order to be able to use remote.conf files from Android. Lirc can't do this.


    thank you for your great job! when will the LibreELEC 8.0 released?

  • Hello,


    Is it possible to disable built-in CEC adapter and use and external (Pulse-Eight) CEC device? I can't power off the TV with built-in CEC device.


    Regards.

  • Nexbox a95x-b7n s905x 1GB/8GB


    I keep getting ignored, so away with my old posts, and bluntness/brevity in.


    Any way to disable HDR completely (e.g SSH commands)?


    Forum search doesn't work to save its own life. Google site search turns this up:

    Code
    1. echo 0 > /sys/module/am_vecm/parameters/hdr_mode


    This changes nothing. Only starting/stopping a vid gets it to correct after any reboot. The OPs last question of "Any way to disable this at boot time?" was never responded to.


    Another G Site Search found this, which was never addressed either:


    Is this even relevant? Creating autostart.sh at the specified location and rebooting again leads to darkness. AFAIK, xrandr should be a component of LibreELEC. Is there a reason it's not here?


    I get it... HDR seems to be a widely ignored and/or sensitive issue for some reason. I know the main post states HDR is buggy, and I know that you can't fix everything. That's fine. It's also not necessary on 99.99% of TVs, so is there any way to just kill it completely to permanently resolve darkness issues? A no will suffice if not. Starting/stopping video changes the video output to the correct parameters... Can logs identify a command that could be applied at startup to just go straight into the right colorspace?

    Nexbox A95X-B7N s905x - 1GB/8GB & 2GB/8GB

    Edited once, last by glitch ().


  • Hello,


    Is it possible to disable built-in CEC adapter and use and external (Pulse-Eight) CEC device? I can't power off the TV with built-in CEC device.


    Regards.


    CEC can be disabled in the Input Devices section of the Kodi GUI. Select the CEC device and change options as necessary.


  • This changes nothing. Only starting/stopping a vid gets it to correct after any reboot.


    Calm down glitch, rel-a-a-ax.
    I can't give you the definite answer you're looking for but, if starting/stopping a video corrects it after reboot, have you tried enabling the kodi start-up animation to give you a start/stop of a video after every reboot?

  • zackito What, the browser?

  • Calm down glitch, rel-a-a-ax.
    I can't give you the definite answer you're looking for but, if starting/stopping a video corrects it after reboot, have you tried enabling the kodi start-up animation to give you a start/stop of a video after every reboot?


    exactly. more of a workaround than a fix, but it works seamlessly. I made a mini how-to for those who like to try this.

    Nexbox A95x (S905X) running kszaq's LE 8.1.10 build


  • exactly. more of a workaround than a fix, but it works seamlessly. I made a mini how-to for those who like to try this.


    Excellent, glad you're sorted now :D


  • SEIKT You have AP6212a chip. Unfortunately there is no BT firmware for that chip in Amlogic sources yet. The other issue is that I don't know how to differentiate AP6212 from AP6212a in systemd.


    Hello, and first I would like to thank you for your great work with LibreElec on S8xx and S9xx


    Having same bluetooth issue because I also have an AP6212, I have found some sources regarding bcmdhdn and support of ap6212 on lichee.


    Could this be helpfull ?


    (I'm really not into drivers, so I'm probably totally out of the subject)

  • Hi, everyone.
    Got mbox(sunvell) t95x (s905x/2g/8gb), just install 7.0.3.012c, video, youtube works fine, but...


    My ISP gives iptv with playlist like this
    #EXTM3U
    #EXTINF:-1 cn-id=10338241,Animal Planet
    udp://@224.3.20.2:1234
    #EXTINF:-1 cn-id=63167341,Game Show
    udp://@224.3.20.120:1234
    #EXTINF:-1 cn-id=10338275,Discovery Channel
    udp://@224.3.20.3:1234
    #EXTINF:-1 cn-id=31559987, ID Xtra
    udp://@224.3.20.178:1234


    Install pvr simple, put playlist into box, configure all, and after reboot have a tv section, all channels with names but then I press OK wheel spinning for some minutes, and return to channels list.
    Log file says


    What can I do?

    Edited once, last by testuser22 ().

  • Just discovered Libreelec. Thanks for amazing software, finally letting me passthrough dts and dolby sound to my receiver! Slightly disappointed when I "upgraded" from version 0.11 64 bit version to 0.12 32 bit. It is so much slower when running from sd now. And I dont have the knowledge to compile own versions. And I dont have the guts to install on nand :).
    Looking forward to try 8.0 builds but I will probably wait if there is no quick way to go back.


    Kind regards
    Ormbett
    (Mini M8SII)

  • I can't find the advancedsettings file to sort outsync issue that i have with 24p movie. I'm looking into my tvbox through samba with my smartphone android, but i can't seem to find the right folder. Where can i find it? Thanks.


    Inviato dal mio Pixel utilizzando Tapatalk

    Edited once, last by Leonxy69 ().

  • Please set resolution in Android to 1080p 60Hz or 50Hz and try again. Is it OK now?


    Yes, now it is ok !!! 1080i / 4K is played without any problem. But strange : even with 1280 * 720 now the whole pictrue is there, yesterday it wasn't


    b) i want to know if my beelink is capable of playing 4:2:2 files. From Samples - Official Kodi Wiki (see MPEG2 4:2:[email protected] 1080i/29.970 35Mbps ) there is an example file and picture is green pixellated mess. Is there a way to play it properly ? Sound is ok.


    Amlogic can't HW decode MPEG2 4:2:2. Only software decoding is available.


    If you disabled HW decoding and use software decoding - the decoding is bad, the picture is there but with big delay and some artifacts....can this be fix somehow ?

    Edited once, last by humaxboy ().


  • I keep getting ignored, so away with my old posts, and bluntness/brevity in.


    Any way to disable HDR completely (e.g SSH commands)?


    You are not being ignored, simply nobody knows how to do this.


    Having same bluetooth issue because I also have an AP6212, I have found some sources regarding bcmdhdn and support of ap6212 on lichee.


    Could this be helpfull ?


    (I'm really not into drivers, so I'm probably totally out of the subject)


    AP6212 is supported here, I need to figure out a workaround to make AP6212a's BT firmware load.



    If you disabled HW decoding and use software decoding - the decoding is bad, the picture is there but with big delay and some artifacts....can this be fix somehow ?


    It seems that this HW is not poerful enough to play MPEG2 4:2:2 content, sorry.

  • Hello,


    I installed this version with "gxbb_p200_2G_1Gbit_RealtekWiFi.dtb" in my Beelink MiniMX III (S905).


    All works as expected, but sometimes when reboots it get blocked in the boot (Beelink logo) and I need to unplug and unplug the power wire.


    Is something wrong with this image?


    Regards.