[8.0.2e] LibreELEC 8.0 for S905/S905X

Hi All,

I've noticed another issue on my Minix U1 with both 7.0.3.012c and 8.0.0d. I'm getting no passthrough on DD+ (E-AC3). It doesn't seem to be a hardware issue, as it works fine on Android with the Minix XBMC. Can anybody else replicate this?

OMG it's quite good works for my Beelink Mini MX 1GB/8GB, thank you so much kszaq! It's more perfect than stock android 5.1.1
It's good for 10bit H264 animation plays without shining dot and much more fast!

Ethernet and wifi, remote all good. But bluetooth headset can connect device, but I can't hear any sound. Only this is small problem
but it's okay!

Quote from frem

Hey, I have an older Tronsmart MXIII Android 4.4.2 TV Box Amlogic S802 Quad Core 2gb/8gb with Openelec flashed on internal. Can I put in an SD card with 8.0 LE on it and it work as good as my Beelink mini MXIII II with 8.0 LE, or is that box too old?

S802-Libreelec images for 7/8/x

Quote from wowwoo

bluetooth headset can connect device, but I can't hear any sound.

Did you goto Settings->System->Audio and select bluetooth/pulse as the audio device?

Hi kszaq,

Not sure if it's already mentioned here, as searching through this thread is not possible.
The last 3-4 seconds of a movie, serie or a clip the video freezes and the sound continues.
A friend of mine has this issue and I also have this issue on both of my S905X devices (both on 8.0.0d).

Another issue that I have, the S905X device that I have downstairs is very sluggish. Browsing through the interface is very slow and it reacts quite slow.
The S905X that I have upstairs is super fast. Both devices have the exact same configuration and are both Nexbox A95X's with the latest firmware.
Any ideas how my S905X downstairs is so slow or where can I look?

Thanks in advanced.

Quote from Jaaxx

Did you goto Settings->System->Audio and select bluetooth/pulse as the audio device?

Thank you for your answer I'll try this
You are the most kind person!

Quote from kszaq

renzz Correct. Echoing 5 will get you 792MHz for S905 and 742MHz for S905X. It might increase smoothness for very heavy skins, although I can see no difference on Estuary which is already running smooth here at standard speed (500MHz).

kszaq - on my box the current value for /sys/class/mpgpu/cur_freq is 500, not a single digit. Should I still change it to just 5 if I want to try the higher frequency?

For info, the contents of every file in /sys/class/mpgpu/ are

Filename: cur_freq
500
Filename: cur_pp
3
Filename: domain_stat
1
Filename: max_freq
5
Filename: max_pp
3
Filename: min_freq
0
Filename: min_pp
1
Filename: mpgpucmd
cat: read error: Input/output error
Filename: scale_mode
1

Hi,

Yesterday i read on some forum about clocking the Mali GPU on the 905/905x, and now i can't find the article. looked thru logs and history, but nothing:(
I'm certain it was for LE and It had something to do with echo x > ?????
Where x was 3 for normal speed and 5 for max speed.

I'm using the Metropolis skin and was hoping this would speed things up a bit:)

-2re

Found it....

Hy!

I have a Beelink Mini MX III II (s905x 2\16gb) and I use LibreELEC-S905.arm-7.0.3.012j and it's working fine. I would like to try LibreELEC-S905.arm-8.0-8.0.0d but it's realy slow on my device. (I tried from usb and from internal to.) Any advise why is that?

Thanks for answers!

Quote from bazsee89

I have a Beelink Mini MX III II (s905x 2\16gb). . .
. . . I would like to try LibreELEC-S905.arm-8.0-8.0.0d but it's realy slow on my device. . .

Hmm. Something's up there, works fine on mine. Have you tried a clean install?

Quote from bazsee89

I have a Beelink Mini MX III II (s905x 2\16gb)

Working fine installed on fast SD card.
Did You try a clean install ?
After upgrade from 7 to 8 I was disappointed

Hi

I am using amlogic s905 MxQ Pro 4K and i have problems with Vol+ and Vol- buttons are not working

it crash image on PVR when i click on them... anyone else experiencing this problem? I am running LibreElec 8.0.0.c direct on flash Nand of STB.. i also tested it on another STB running from SD card libreelec and the same problema happens vol+ and vol- buttons are not working it simply crashes image

i tried to upload my original android remote.conf to /etc/amremote folder

but i cannot i dont have access rights even running root.. any ideas on how i can fix this?

Quote from Xitro01

Hi kszaq,

Not sure if it's already mentioned here, as searching through this thread is not possible.
The last 3-4 seconds of a movie, serie or a clip the video freezes and the sound continues.
A friend of mine has this issue and I also have this issue on both of my S905X devices (both on 8.0.0d).

i'm having the same issue, and i thought the plex plugin was at fault but now i guess it's not

Quote from Ilfrance

i'm having the same issue, and i thought the plex plugin was at fault but now i guess it's not

i am shure its a config on the remote.conf code

i tried remount, rw flash

but cannot edit or add files on the system still, so i cannot make further testing

logicheart
This could be a thermal problem. I may be that the pad that connects the heatsink with processor has become loose and so the latter might overheat sooner than later. In order to check this, you have to open the box, unscrew the board and cautiously see if you can lift the board. If not, then all is well, if it is rather easy, then there was no connection between the heasink and the S905X.

Best wishes, dfahren

Quote from logicheart

Hello...

I had a Mini M8S II box and now i have a Tanix TX5 Pro TV box...

I had freezes and Kodi restarts with Mini M8S II and i also have now with Tanix TX5 Pro...

Setup is typical LibreELEC 8.0.0c with as few addons as i can...

I have tested both versions, with or without thermal sensor without any luck...

The only thing i have noticed with Krypton is that now the box does not freeze anymore, only Kodi is restarting and also this issue is not so frequent as before...

Does anyone have any idea why this is happening?

Best regards...

Display More

Ok guys sorted it out

mount -o remount,rw /flash

then copy original remote.conf to /storage/flash

reboot device it will work, mine just got back

original S905 Remote.Conf

#*********************************************************************************************************
#this file is configuration for each factory remote device
# work_mode  0 :software mode  1 :hardware mode
# repeat_enable  0 :disable repeat 1 :enable repeat
#
# factory_code      each device has it's unique factory code.
#  pattern:custom_code(16bit)+index_code(16bit)
#  examble: 0xff000001 = 0xff00(custom cod)  0001 (index)
#
# release_delay  unit:ms.release will report from kernel to user layer after this period of time
#  from press or repeat triggered.
#
# debug_enable      0 :debug disable  1 :debug disable
#
# SW MODE:
# bit_count  how many bits in each frame
# tw_leader_act  time window for leader active
# tw_bit0  time window for bit0 time.
# tw_bit1  time window for bit1 time
# tw_repeat_leader  time window for repeat leader
# REG
# reg_base_gen  set value for PREG_IR_DEC_BASE_GEN
# reg_control  set value for PREG_IR_DEC_CONTROL
# reg_leader_act  set value for PREG_IR_DEC_LEADER_ACTIVE
# reg_leader_idle  set value for PREG_IR_DEC_LEADER_IDLE
# reg_repeat_leader set value for PREG_IR_DEC_REPEAT_IDLE
# reg_bit0_time  set value for PREG_IR_DEC_BIT0_TIME
#*************************************************************************************************************
#amlogic NEC remote
factory_code = 0x40400001 
work_mode   = 0
repeat_enable = 1
repeat_delay = 40
repeat_peroid = 39
release_delay = 121
debug_enable = 1


fn_key_scancode    = 0x44
left_key_scancode  = 0x10
right_key_scancode = 0x11
up_key_scancode    = 0x0b
down_key_scancode  = 0x0e
ok_key_scancode    = 0x0d
pageup_key_scancode = 0x04
pagedown_key_scancode = 0x1b


mouse_begin
0 0x10
1 0x11
2 0x0b
3 0x0e
mouse_end


key_begin
0x43 113
    0x1c 114
    0x15 115
    0x10 105
    0x0b 103
    0x11 106
    0x0e 108
    0x0d 97
    0x42 158 
    0x1a 172
    0x4d 116
    0x45 139
    0x44 388
    0x01 2
    0x02 3
    0x03 4
    0x04 5
    0x05 6
    0x06 7
    0x07 8
    0x08 9
    0x09 10
    0x00 11
    0x0f 389
    0x0c 14
    0x1e 122
    0x1f 123
    0x53 393
    0x5b 390
    0x57 70
    0x54 392
    0x2f 392
    0x2e 141
    
    
    
    
    
key_end
repeat_key_begin
0x4d 113
    0x1c 114
    0x15 115
    0x10 105
    0x0b 103
    0x11 106
    0x0e 108
    0x0d 28
    0x42 158 
    0x1a 172
    0x4d 116
    0x45 139
    0x44 388
    0x01 2
    0x02 3
    0x03 4
    0x04 5
    0x05 6
    0x06 7
    0x07 8
    0x08 9
    0x09 10
    0x00 11
    0x0f 389
    0x0c 111
    0x1e 122
    0x1f 123
    0x53 164
    0x5b 390
    0x57 70
    0x54 392
    0x2f 392
    0x2e 141
repeat_key_end

There is no need to mount the flash or system area and modify it!

Simply put your modified/own remote.conf file in the .config directory in the home directory ("Configfiles" on SMB share). Startup will load this config instead of system config.

Quote from tester100

i am shure its a config on the remote.conf code

i tried remount, rw flash

but cannot edit or add files on the system still, so i cannot make further testing

I don't think that's the problem, as LibreELEC 7.0 on this box did not have this issue. And I use the same remote.conf.
I think you are replying to the wrong message.