Tvheadend does scan mux failed

  • hey. I’m using a RTL2832U USB Tv tuner. Here’s what I already did.

    -DVB tools

    -crazy cat

    -w_scan (works)


    however, mixes scanning results is always fail. Is it my USB tv tuner that is not working?

    But if w_scan starts to scan does it mean my tv tuner is working?

    If it’s not working, I’ve downloaded a firmware (.gz) I’m not sure how to install.

    Help would be appreciated!

  • Probably it will be easier to say what tuner you are using then just RTL2832U...

    Usually if the scan fails is either because there are no TV channels on that mux or you have poor reception..

    So if your tuner is recognized by tvheadend...start with creating a network for your area from the ready made

    pre defined muxes...then go back to your adaptor and assign that network..then scan.

    If it will fail try the Generic pre defined list (takes longer to scan)but has almost all dvb-t muxes included so you can t go wrong with that.

  • Probably it will be easier to say what tuner you are using then just RTL2832U...

    Usually if the scan fails is either because there are no TV channels on that mux or you have poor reception..

    So if your tuner is recognized by tvheadend...start with creating a network for your area from the ready made

    pre defined muxes...then go back to your adaptor and assign that network..then scan.

    If it will fail try the Generic pre defined list (takes longer to scan)but has almost all dvb-t muxes included so you can t go wrong with that.

    It is just a generic tuner. i got it from tv-card-usb-wireless-transmission-receiver-ads-b-tuner-audio-computer-video-capture-rtl2832u-r820t-dvb-t-i.64917281.6700767213

    Also my tuner appears on tvheadend, so does it automatically means my tuner is supported?

    My area does not have a ready made pre-defined muxes. And my area is using dvb-t2.

    Or maybe i have to install some sort of drivers for it but i do not know how to.

    Thanks for replying though. :)

  • Does anyone have tips on how to select a tv tuner that is compatible? Also most of them need a driver but i have no idea how should i install it. Pretty new to Linux.

    :)

  • I have a similar problem with my DVBSKY S960:

    On Raspberry pi 4 (9.1.502 fresh installation) the following happens:

    1) after boot everything works fine and the tuner scans muxes and services are found.

    2) after some time all scans fail with the following error msg:

    Code
    2019-10-30 21:23:52.099 mpegts: 10979V in Astra - tuning on Montage Technology M88DS3103 #0 : DVB-S #0
    2019-10-30 21:23:52.102 subscription: 0107: "scan" subscribing to mux "10979V", weigh: 6, adapter: "Montage Technology M88DS3103 #0 : DVB-S #0", network: "Astra", service: "Raw PID Subscription"
    2019-10-30 21:23:53.286 linuxdvb: Montage Technology M88DS3103 #0 : DVB-S #0 - poll TIMEOUT
    2019-10-30 21:23:53.486 linuxdvb: Montage Technology M88DS3103 #0 : DVB-S #0 - retune nodata
    2019-10-30 21:24:00.946 linuxdvb: Montage Technology M88DS3103 #0 : DVB-S #0 - poll TIMEOUT
    2019-10-30 21:24:01.534 linuxdvb: Montage Technology M88DS3103 #0 : DVB-S #0 - retune nodata
    2019-10-30 21:24:02.094 mpegts: 10979V in Astra - scan no data, failed2019-10-30 21:24:02.094 subscription: 0107: "scan" unsubscribing

    Ths happens for _all_ muxes from that point on.

    Any ideas?

  • I have Rpi 4 with libreelec and DVBSKY s960 and it also happens to me with an FTA mux

    in this mux there is only one channel if you scan it but only partially and it does not lower the channel

    only this mux gives me this probeam

    did you fix it?

    12077 V 4000 5/6 DVB S2 QPSK2

    Edited once, last by espaun206 (March 29, 2020 at 8:56 AM).