Hello
I just got a new NUC11 i3 and when directly connected to my TV LE loads but via my Denon 4700H AVR I get no picture or sound.
Anyone else solve this?
I updated NUC to latest BIOS and running latest nightly of LE.
NUC11PAKi3 and Denon AVR No Output
- Nekromantik
-
January 30, 2023 at 3:15 PM - Thread is Unresolved
-
Please provide a full debug log.
How to post a log (wiki)
1. Enable debugging in Settings>System Settings>Logging
2. Restart Kodi
3. Replicate the problem
4. Generate a log URL (do not post/upload logs to the forum)
use "Settings > LibreELEC > System > Paste system logs" or run "pastekodi" over SSH, then post the URL link -
Please provide a full debug log.
How to post a log (wiki)
1. Enable debugging in Settings>System Settings>Logging
2. Restart Kodi
3. Replicate the problem
4. Generate a log URL (do not post/upload logs to the forum)
use "Settings > LibreELEC > System > Paste system logs" or run "pastekodi" over SSH, then post the URL linkdo you mean plug direct into TV so I can enable debug and then power off plug into AVR and boot and then SSH in to get logs?
wont be able to use LE settings if I get no display output
-
Did you migrate the HDD from an older device to the newer one?
If yes, do "systemctl stop kodi && mv /storage/.kodi /storage/.kodi-old && systemctl start kodi" as an experiment to see if moving all the old config out of the way resolves something.
2023-01-30 20:58:25.001 T:770 debug <general>: CDRMUtils::SetMode - found crtc mode: 3840x2160 @ 60 Hz
2023-01-30 20:58:25.001 T:770 debug <general>: CGBMUtils::CreateSurface - created surface with size 1920x1080^ that looks wrong to me
It's odd that it claims to have no ELD data, but then finds all the resolutions and there is HDMI audio showing. It might be a case where the upstream drivers are still work in progress.
-
Did you migrate the HDD from an older device to the newer one?
If yes, do "systemctl stop kodi && mv /storage/.kodi /storage/.kodi-old && systemctl start kodi" as an experiment to see if moving all the old config out of the way resolves something.
2023-01-30 20:58:25.001 T:770 debug <general>: CDRMUtils::SetMode - found crtc mode: 3840x2160 @ 60 Hz
2023-01-30 20:58:25.001 T:770 debug <general>: CGBMUtils::CreateSurface - created surface with size 1920x1080^ that looks wrong to me
It's odd that it claims to have no ELD data, but then finds all the resolutions and there is HDMI audio showing. It might be a case where the upstream drivers are still work in progress.
So yes I moved the USB drive from old NUC6 to NUC11.
Others seem to be using this NUC on LE and having audio issues instead of image so cant be drivers. Its a 1.5 year old NUC now as Gen 12 is out. Could it be a LE11 issue? Shall I try LE10?
-
Shall I try LE10?
Whatever works for you, works for us.
-
It sounds like a driver issue but these days I have low knowledge on the true state of Intel hardware support (hardware is not impossible, but improbable). If it works with DP > HDMI, stick with what works (at least for now).
-
I was having a similar issue running through my nuc11 through a yamaha 3060. I had initially installed LE connected to a computer monitor and then swapped to my AVR/projector. Re-installing only connected to the AVR/projector fixed my problem.
prior to reinstalling, I copied the EDID, which also got the display working, but for some reason VAAPI hardware decoding did not work until I did a fresh install.
now I’m running into refresh rate issues: RE: LE11 HDR builds for Intel and AMD
