NUC11PAKi3 and Denon AVR No Output

    Hello

    I just got a new NUC11 i3 and when directly connected to my TV LE loads but via my Denon 4700H AVR I get no picture or sound.

    Anyone else solve this?

    I updated NUC to latest BIOS and running latest nightly of LE.

    Please provide a full debug log.

    How to post a log (wiki)

    1. Enable debugging in Settings>System Settings>Logging
    2. Restart Kodi
    3. Replicate the problem
    4. Generate a log URL (do not post/upload logs to the forum)

    use "Settings > LibreELEC > System > Paste system logs" or run "pastekodi" over SSH, then post the URL link
    Quote from chewitt
    Please provide a full debug log.

    How to post a log (wiki)

    1. Enable debugging in Settings>System Settings>Logging
    2. Restart Kodi
    3. Replicate the problem
    4. Generate a log URL (do not post/upload logs to the forum)

    use "Settings > LibreELEC > System > Paste system logs" or run "pastekodi" over SSH, then post the URL link

    do you mean plug direct into TV so I can enable debug and then power off plug into AVR and boot and then SSH in to get logs?

    wont be able to use LE settings if I get no display output

    Did you migrate the HDD from an older device to the newer one?

    If yes, do "systemctl stop kodi && mv /storage/.kodi /storage/.kodi-old && systemctl start kodi" as an experiment to see if moving all the old config out of the way resolves something.

    2023-01-30 20:58:25.001 T:770 debug <general>: CDRMUtils::SetMode - found crtc mode: 3840x2160 @ 60 Hz
    2023-01-30 20:58:25.001 T:770 debug <general>: CGBMUtils::CreateSurface - created surface with size 1920x1080

    ^ that looks wrong to me

    It's odd that it claims to have no ELD data, but then finds all the resolutions and there is HDMI audio showing. It might be a case where the upstream drivers are still work in progress.

    Quote from chewitt

    Did you migrate the HDD from an older device to the newer one?

    If yes, do "systemctl stop kodi && mv /storage/.kodi /storage/.kodi-old && systemctl start kodi" as an experiment to see if moving all the old config out of the way resolves something.

    2023-01-30 20:58:25.001 T:770 debug <general>: CDRMUtils::SetMode - found crtc mode: 3840x2160 @ 60 Hz
    2023-01-30 20:58:25.001 T:770 debug <general>: CGBMUtils::CreateSurface - created surface with size 1920x1080

    ^ that looks wrong to me

    It's odd that it claims to have no ELD data, but then finds all the resolutions and there is HDMI audio showing. It might be a case where the upstream drivers are still work in progress.

    So yes I moved the USB drive from old NUC6 to NUC11.

    Others seem to be using this NUC on LE and having audio issues instead of image so cant be drivers. Its a 1.5 year old NUC now as Gen 12 is out. Could it be a LE11 issue? Shall I try LE10?

    It sounds like a driver issue but these days I have low knowledge on the true state of Intel hardware support (hardware is not impossible, but improbable). If it works with DP > HDMI, stick with what works (at least for now).

    I was having a similar issue running through my nuc11 through a yamaha 3060. I had initially installed LE connected to a computer monitor and then swapped to my AVR/projector. Re-installing only connected to the AVR/projector fixed my problem.

    prior to reinstalling, I copied the EDID, which also got the display working, but for some reason VAAPI hardware decoding did not work until I did a fresh install.

    now I’m running into refresh rate issues: RE: LE11 HDR builds for Intel and AMD