Common DVB-T DVB-S dvb-c topic

**afl1** · October 7, 2016 at 8:57 AM

I repacked installation packages to fix some install issues.

SDcard versions:
LibreELEC-Amlogic.aarch64-KI_Plus-7.0.2.004.2.img.gz
LibreELEC-Amlogic.aarch64-KII_Pro-7.0.2.004.2.img.gz

Install SDcard version to internal connecting to box via ssh and submiting command: /flash/installtointernal
Don't use kszaq version of 'installtointernal' otherwise u brick your box.

Internal flash versions:
LibreELEC-Amlogic.aarch64-KI_Plus-7.0.2.004.2.zip
LibreELEC-Amlogic.aarch64-KII_Pro-7.0.2.004.2.zip
Unzip file to SDcard or USB stick. Install from recovery or Android update apk.

[hr]

Quote from qashaf

i tested dvbt2, scanning fail but dvbs2 working well. blutooth also working successful. i aware that dvbs2 signal low 10% compare to my enigma2 box. normal signal for certain transponder 80-90%, but with k2pro around 70-80%. . tuner sensitivity also weak, this factors gave no signal or lost during scan or livetv. i dont know what is the minimum signal that suitable the box to scan successsfully.

Signal level is very informative value and hard to compare between different boxes. Most important is SNR. 50% is enough for HD channels. Most important parts are satellite dish and LNB. Tuner can hardly improve bad signal. If u have low signal on tuner u have to use LNB with higher gain.

segment · October 7, 2016 at 9:53 AM

drivers for AVL6862 have errors, problems with transporters
on the TP 10834 V tp 116 DVB-S2 8PSK SR 27500 FEC 3/4 11258 H tp 3 DVB-S2 8PSK SR 27500 FEC 3/4 ceases to decode, it looks at the loss of signal

log from the kernel since then
[ 3876.586522@1] avl6862fe_strength: SIGNAL_STRENGTH = 47185, ret = 0
[ 3876.586853@1] avl6862fe_snr: SNR = 36044, ret = 0
[ 3876.586860@1] avl6862_read_ber: ok!
[ 3876.586866@1] avl6862_read_ucblocks: ok!

qashaf · October 7, 2016 at 10:13 AM

Quote from willyfan

Sanning fail but tuner is working in some way. I noticed that every time I restart the KII I found more service in the network . It add a mux time by time, may be one mux every restart. But service are not mapped in channel. I tried to "map service" manually (map all service) and channel is added to the list, and also in kodi.
But... if I click on the channel on kodi, the stream don't start (no signal) until I open the channel from web interface with look TV. Actually I have 148 Service, 94 channel but only a few are working (and only with matroska stream profile)

what i understand from wetek forum, this is tvheadend bug for first time open stream livetv
[hr]

Quote from afl1

I repacked installation packages to fix some install issues.

SDcard versions:
LibreELEC-Amlogic.aarch64-KI_Plus-7.0.2.004.2.img.gz
LibreELEC-Amlogic.aarch64-KII_Pro-7.0.2.004.2.img.gz

Install SDcard version to internal connecting to box via ssh and submiting command: /flash/installtointernal
Don't use kszaq version of 'installtointernal' otherwise u brick your box.

Internal flash versions:
LibreELEC-Amlogic.aarch64-KI_Plus-7.0.2.004.2-update.zip
LibreELEC-Amlogic.aarch64-KII_Pro-7.0.2.004.2-update.zip

Unzip file to SDcard or USB stick. Install from recovery or Android update apk.
[hr]

Signal level is very informative value and hard to compare between different boxes. Most important is SNR. 50% is enough for HD channels. Most important parts are satellite dish and LNB. Tuner can hardly improve bad signal. If u have low signal on tuner u have to use LNB with higher gain.

Display More

i tested dvbs2 with 6in' dish high gain lnb (very high signal snr n stregth using satfinder and other box about 90-100%, several tp 80-90%, when using k2pro shows 70-80%), t2 still not working during scan...i think this is because of dvb drivers

pawnthep · October 7, 2016 at 11:21 AM

Quote from afl1

I repacked installation packages to fix some install issues.

SDcard versions:
LibreELEC-Amlogic.aarch64-KI_Plus-7.0.2.004.2.img.gz
LibreELEC-Amlogic.aarch64-KII_Pro-7.0.2.004.2.img.gz

Install SDcard version to internal connecting to box via ssh and submiting command: /flash/installtointernal
Don't use kszaq version of 'installtointernal' otherwise u brick your box.

Internal flash versions:
LibreELEC-Amlogic.aarch64-KI_Plus-7.0.2.004.2-update.zip
LibreELEC-Amlogic.aarch64-KII_Pro-7.0.2.004.2-update.zip

Unzip file to SDcard or USB stick. Install from recovery or Android update apk.

Display More

I tried install Kii pro's Internal flash version but the box just goes to recovery only and nothing installed.

BTW, unzipped files do not have files like aml_autoscript, factory_update_param.aml.

Edited: just tried install KII_Pro-7.0.2.004.2.img.gz on SDcard too. It boots but only stuck at LibreELEC logo.

K 2 pro · October 7, 2016 at 11:31 AM

hi
after test image LibreELEC-Amlogic.aarch64-KI_Plus-7.0.2.004.1.img.gz
very stable
wifi .... OK
VDR .... OK
tuner dvbs2 ..... Ok
cccam in OsCAM ....... OK Very fast to open an encrypted
-----------------
Have a problem
Preparation lnb disque 4x1
not working
and Do not captures channels 4K
thanks

segment · October 7, 2016 at 11:49 AM

@K 2 pro Check Hotbird 13E, there are problems with dvb

qashaf · October 7, 2016 at 12:35 PM

Quote from K 2 pro

hi
after test image LibreELEC-Amlogic.aarch64-KI_Plus-7.0.2.004.1.img.gz
very stable
wifi .... OK
VDR .... OK
tuner dvbs2 ..... Ok
cccam in OsCAM ....... OK Very fast to open an encrypted
-----------------
Have a problem
Preparation lnb disque 4x1
not working
and Do not captures channels 4K
thanks

Display More

i use tvheadend 4.2, diseqc 1.0 OK

sauna · October 7, 2016 at 12:48 PM

on LibreELEC-Amlogic.aarch64-KI Plus-7.0.2.004.1.img.gz dvb-t works.you need to disable dvb-s adapter.when viewed dvb-s to disable the dvb-t adaptor.they do not work together.

**afl1** · October 7, 2016 at 1:05 PM

Quote from pawnthep

I tried install Kii pro's Internal flash version but the box just goes to recovery only and nothing installed.

BTW, unzipped files do not have files like aml_autoscript, factory_update_param.aml.

Edited: just tried install KII_Pro-7.0.2.004.2.img.gz on SDcard too. It boots but only stuck at LibreELEC logo.

Sorry wrong versions. I fixed them.

segment · October 7, 2016 at 1:25 PM

LibreELEC-Amlogic.aarch64-KI_Plus-7.0.2.004.2 - Not working in NAND, stands on the logo S905.
SD also the same stops logo Amlogic S905

envagyok · October 7, 2016 at 2:37 PM

Quote from sauna

on LibreELEC-Amlogic.aarch64-KI Plus-7.0.2.004.1.img.gz dvb-t works.you need to disable dvb-s adapter.when viewed dvb-s to disable the dvb-t adaptor.they do not work together.

No!
You can use both tuner, but only one a time.
You must enable power save settings at both tuner (dvb-t and dvb-s)

Then when you watch dvb-s turn on dvb-s tuner. Then stop streaming, and switch to dvb-t, then dvb-s goes to standby, and switch to dvb-t

K 2 pro · October 7, 2016 at 3:58 PM

Quote from qashaf

i use tvheadend 4.2, diseqc 1.0 OK

problem use tvheadend 4.2

not connecting tuner dvbs2

When entering tv adapter I find empty

**edit4ever** · October 7, 2016 at 5:45 PM

Quote from afl1

Sorry wrong versions. I fixed them.

~~Link shows file has been deleted.~~

My mistake - I needed to go back to the original post!
LibreELEC

Coollio · October 7, 2016 at 6:23 PM

What about AC3, DTS, DD ?

**afl1** · October 7, 2016 at 7:52 PM

Quote from segment

LibreELEC-Amlogic.aarch64-KI_Plus-7.0.2.004.2 - Not working in NAND, stands on the logo S905.
SD also the same stops logo Amlogic S905

Fixed. It was my mistake in building KI Plus version.
[hr]

Quote from Coollio

What about AC3, DTS, DD ?

All HD audio formats are supported.

For HDMI:
Passthrough: DD, DD+, TrueHD, DTS, DTS96, DTS-HD, DTS-HR, Multichannel PCM
Transcoding to Multichannel PCM: DD, DD+, TrueHD, DTS, DTS96, DTS-HD, DTS-HR, DSD
Transcoding to DD: TrueHD, DTS, DTS96, DTS-HD, DTS-HR, DSD

For SPDIF:
Passthrough: DD, DD+, DTS, DTS96
Transcoding to DD: TrueHD, DTS, DTS96, DTS-HD, DTS-HR, Multichannel PCM, DSD

Coollio · October 7, 2016 at 8:22 PM

Thank you... DVB-S2 working is well ?

qashaf · October 7, 2016 at 9:31 PM

Quote from K 2 pro

problem use tvheadend 4.2

not connecting tuner dvbs2

When entering tv adapter I find empty

for first time open a channel on livetv, bug no signal. try open another channel..become OK

**edit4ever** · October 7, 2016 at 11:08 PM

afl1 - I'm working to get my ATSC version of the K2Pro working under your build. I'm having trouble getting the wifi to function. My device tree needs to be different as the power and interrupt pins for wifi are 238 and 239 instead of 234 and 235 like on the standard boxes. Also I have a gigabit lan chip.

I've made the changes in the dtb file that should enable these to function.

Code

wifi {
        compatible = "amlogic, aml_broadcm_wifi";
        dev_name = "aml_broadcm_wifi";
        status = "okay";
        interrupt_pin = <0x20 0x67 0x0>;
        interrupts = <0x0 0x44 0x4>;
        irq_trigger_type = "GPIO_IRQ_LOW";
        power_on_pin = <0x20 0x66 0x0>;
        pinctrl-names = "wifi_32k_pins";
        pinctrl-0 = <0x24>;
    };


    ethernet@0xc9410000 {
        compatible = "amlogic, gxbb-rgmii-dwmac";
        reg = <0x0 0xc9410000 0x0 0x10000 0x0 0xc8834540 0x0 0x8>;
        interrupts = <0x0 0x8 0x1>;
        phy-mode = "rgmii";
        pinctrl-names = "eth_pins";
        pinctrl-0 = <0x1f>;
        rst_pin-gpios = <0x20 0xe 0x0>;
        mc_val = <0x1621>;
        resets = <0xc 0x23>;
        reset-names = "ethpower";
        interrupt-names = "macirq";
        clocks = <0xc 0xa>;
        clock-names = "ethclk81";
    };

Display More

Lan is working - but wifi is having issues.

Here is the dmesg output: K2proATSC-dmesg.zip

This change worked on kszaq's builds...but I know that is a different kernel.

Thanks for any insight!

-- additional info:

Here is the dmesg output when I delete the dtb.img and let it boot: K2proATSC-orig-dmesg.zip