How install LE on bricked box?

bumerc · Nov 21st 2018

USB interface is detected, that's good. Install u-boot.bin.sd.bin via BootcardMaker (see method 3), insert the SDcard into the card slot of the box and start it again.

ErsFreezy · Jun 25th 2019

Quote from bumerc

USB interface is detected, that's good. Install u-boot.bin.sd.bin via BootcardMaker (see method 3), insert the SDcard into the card slot of the box and start it again.

where I can get a uboot file for a M8s Pro L (lq version)

I have the problem that I cant flash the box via Usb Burning tool. It always stops at 2% and give me the romcode error. Tried everything but nothing works..

tananhcctv · Feb 21st 2020

Quote from bumerc

This is correct, because these two partitions are not yet formatted. The bootloader was written from offset 0 into the SD card. This area is not visible in user space. Is the device recognized in the AML Burning Tool?

I used UART to USB, it just stood there! My box S905x, Ram 1G!
PLEASE HELP ME

Code

GXL:BL1:9ac50e:a1974b;FEAT:ADFC318C;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 170247

BL2 Built : 12:23:15, May 17 2019. gxl g3e531ea - [email protected]

set vcck to 1120 mv
set vddee to 1000 mv
Board ID = 1
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 768MHz - FAIL
DDR3 chl: Rank0 @ 768MHz
bist_test rank: 0 26 08 44 35 15 55 23 08 3f 36 16 57 26 07 45 30 10 50 25 08 42 37 1a 55 685   - PASS

Rank0: 1024MB(auto)-2T-11
AddrBus test pass!
eMMC boot @ 0
sw8 s
emmc switch 3 ok
Authentication key not yet programmed
get rpmb counter error 0x00000007
emmc switch 0 ok
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000, part: 0
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x013c0000, size: 0x0000d600, part: 0
Load bl31 from eMMC, src: 0x00020200, des: 0x05100000, size: 0x0002b400, part: 0
Load bl33 from eMMC, src: 0x0004c200, des: 0x01000000, size: 0x0007fa00, part: 0
NOTICE:  BL3-1: v1.0(release):53f813e
NOTICE:  BL3-1: Built : 15:51:23, May 22 2019
[BL31]: GXL CPU setup!
NOTICE:  BL3-1: GXL normal boot!
NOTICE:  BL3-1: BL33 decompress pass
mpu_config_enable:system pre init ok
dmc sec lock
[Image: gxl_v1.1.3389-92241b5 2019-07-02 17:22:35 [email protected]]
OPS=0x82
21 0b 82 00 1a 33 11 09 78 5c 6b 6c 59 51 36 f8
[0.664577 Inits done]
secure task start!
high task start!
low task start!
ERROR:   Error initializing runtime service opteed_fast


U-Boot 2015.01-g3f780c9 (Aug 23 2019 - 13:51:26)

DRAM:  1 GiB
Relocation Offset is: 36e7a000
register usb cfg[0][1] = 0000000037f4b2e8
[CANVAS]canvas init
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
aml_i2c_init_port init regs for 2
MMC:   aml_priv->desc_buf = 0x0000000033e7a6b0
aml_priv->desc_buf = 0x0000000033e7c9f0
SDIO Port B: 0, SDIO Port C: 1
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, status=0x1ff2800
emmc/sd response timeout, cmd55, status=0x1ff2800
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 40000000
[mmc_startup] mmc refix success
init_part() 297: PART_TYPE_AML
[mmc_init] mmc init success
      Amlogic multi-dtb tool
      Single dtb detected
start dts,buffer=0000000033e7f240,dt_addr=0000000033e7f240
get_partition_from_dts() 91: ret 0
      Amlogic multi-dtb tool
      Single dtb detected
parts: 17
00:      logo   0000000000800000 1
01:  recovery   0000000001800000 1
02:      misc   0000000000800000 1
03:      dtbo   0000000000800000 1
04:  cri_data   0000000000800000 2
05:     param   0000000001000000 2
06:      boot   0000000001000000 1
set has_boot_slot = 0
07:       rsv   0000000001000000 1
08:  metadata   0000000001000000 1
09:    vbmeta   0000000000200000 1
10:       tee   0000000002000000 1
11:    vendor   0000000014000000 1
12:       odm   0000000008000000 1
13:    system   0000000050000000 1
14:   product   0000000008000000 1
15:     cache   0000000046000000 2
16:      data   ffffffffffffffff 4
init_part() 297: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
crc32_s:0x1577dad == storage crc_pattern:0x1577dad!!!
crc32_s:0xee152b83 == storage crc_pattern:0xee152b83!!!
crc32_s:0x7fd3b243 == storage crc_pattern:0x7fd3b243!!!
mmc env offset: 0x4d400000
In:    serial
Out:   serial
Err:   serial
reboot_mode=cold_boot
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-3406: calc ec163d72, store ec163d72
_verify_dtb_checksum()-3406: calc ec163d72, store ec163d72
dtb_read()-3623: total valid 2
update_old_dtb()-3604: do nothing
      Amlogic multi-dtb tool
      Single dtb detected
vpu: clk_level in dts: 7
vpu: vpu_power_on
vpu: set clk: 666667000Hz, readback: 666666667Hz(0x300)
vpu: vpu_module_init_config
vpp: vpp_init
cvbs: cpuid:0x21
hpd_state=0
vpp: vpp_matrix_update: 2
cvbs performance type = 6, table = 0
cvbs_config_hdmipll_gxl
cvbs_set_vid2_clk
Net:   dwmac.c9410000amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0

CONFIG_AVB2: null
Start read misc partition datas!
info->magic =
info->version_major = 1
info->version_minor = 0
info->slots[0].priority = 15
info->slots[0].tries_remaining = 7
info->slots[0].successful_boot = 0
info->slots[1].priority = 14
info->slots[1].tries_remaining = 7
info->slots[1].successful_boot = 0
info->crc32 = -1075449479
active slot = 0
wipe_data=successful
wipe_cache=successful
upgrade_step=2
reboot_mode:::: cold_boot
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L515:key[deviceid] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[region_code] not programed yet
[OSD]load fb addr from dts:/meson-fb
[OSD]fb_addr for logo: 0x7f800000
[OSD]load fb addr from dts:/meson-fb
[OSD]fb_addr for logo: 0x7f800000
[OSD]VPP_OFIFO_SIZE:0xfff00fff
[CANVAS]addr=0x7f800000 width=3840, height=2160
[OSD]osd_hw.free_dst_data: 0,719,0,575
The Board don't support KBI interface
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L515:key[deviceid] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[region_code] not programed yet
gpio: pin GPIOAO_2 (gpio 102) value is 0
detect upgrade key
gpio: pin GPIOAO_2 (gpio 102) value is 1
Command: bcb uboot-command
Start read misc partition datas!
BCB hasn't any datas,exit!
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L515:key[deviceid] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[region_code] not programed yet
Hit Enter or space or Ctrl+C key to stop autoboot -- :  0
CONFIG_SYSTEM_AS_ROOT: systemroot
system_mode: 1
Start read misc partition datas!
info->magic =
info->version_major = 1
info->version_minor = 0
info->slots[0].priority = 15
info->slots[0].tries_remaining = 7
info->slots[0].successful_boot = 0
info->slots[1].priority = 14
info->slots[1].tries_remaining = 7
info->slots[1].successful_boot = 0
info->crc32 = -1075449479
active slot = 0
CONFIG_AVB2: null
active_slot: normal avb2: 0
avb2: 0
ee_gate_off ...
avb2: 0
## Booting Android Image at 0x01080000 ...
Kernel command line: androidboot.dtbo_idx=0 --cmdline root=/dev/mmcblk0p18 buildvariant=userdebug
Start read misc partition datas!
info->magic =
info->version_major = 1
info->version_minor = 0
info->slots[0].priority = 15
info->slots[0].tries_remaining = 7
info->slots[0].successful_boot = 0
info->slots[1].priority = 14
info->slots[1].tries_remaining = 7
info->slots[1].successful_boot = 0
info->crc32 = -1075449479
active slot = 0
active_slot is normal
load dtb from 0x1000000 ......
      Amlogic multi-dtb tool
      Single dtb detected
find 1 dtbos
dtbos to be applied: 0
Apply dtbo 0
   Loading Kernel Image(COMP_NONE) ... OK
   kernel loaded at 0x01080000, end = 0x019abd38
   Loading Device Tree to 0000000009fef000, end 0000000009fffed4 ... OK
fdt_instaboot: no instaboot image

Starting kernel ...

uboot time: 5022924 us
[    [email protected]] Booting Linux on physical CPU 0x0
[    [email protected]] Linux version 4.9.113-g6880ef4-dirty ([email protected]) (gcc version 6.3.1 20170109 (Linaro GCC 6.3-2017.02) ) #5 SMP PREEMPT Thu Aug 22 16:00:30 CST 2019
[    [email protected]] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c5383d
[    [email protected]] CPU: div instructions available: patching division code
[    [email protected]] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    [email protected]] OF: fdt:Machine model: Khadas
[    [email protected]] earlycon: aml_uart0 at MMIO 0xc81004c0 (options '')
[    [email protected]] bootconsole [aml_uart0] enabled
[    [email protected]] page_trace enabled
[    [email protected]] Reserved memory: created CMA memory pool at 0x05000000, size 4 MiB
[    [email protected]] OF: reserved mem: initialized node linux,secmon, compatible id shared-dma-pool
[    [email protected]] Reserved memory: created CMA memory pool at 0x7f800000, size 8 MiB
[    [email protected]] OF: reserved mem: initialized node linux,meson-fb, compatible id shared-dma-pool
[    [email protected]] Reserved memory: created CMA memory pool at 0x7d800000, size 32 MiB
[    [email protected]] OF: reserved mem: initialized node linux,di_cma, compatible id shared-dma-pool
[    [email protected]] Reserved memory: created CMA memory pool at 0x75c00000, size 124 MiB
[    [email protected]] OF: reserved mem: initialized node linux,ion-dev, compatible id shared-dma-pool
[    [email protected]] Reserved memory: created CMA memory pool at 0x74c00000, size 16 MiB
[    [email protected]] OF: reserved mem: initialized node linux,vdin1_cma, compatible id shared-dma-pool
[    [email protected]] Reserved memory: regions without no-map are not yet supported
[    [email protected]] Reserved memory: created CMA memory pool at 0x61800000, size 308 MiB
[    [email protected]] OF: reserved mem: initialized node linux,codec_mm_cma, compatible id shared-dma-pool
[    [email protected]] Reserved memory: unable to setup CMA region
[    [email protected]] OF: reserved mem: initialized node linux,codec_mm_reserved, compatible id amlogic, codec-mm-reserved
[    [email protected]] cma: Reserved 8 MiB at 0x61000000
[    [email protected]] Memory policy: Data cache writealloc

Display More

chewitt · Feb 22nd 2020

Your box is booting some Android kernel .. it is not booting LE.

tananhcctv · Feb 26th 2020

Quote from chewitt

Your box is booting some Android kernel .. it is not booting LE.

Now I have to get it back to normal ?

Please Help me ?

Thank you very much !

bubblegum57 · Feb 26th 2020

Quote from tananhcctv

Now I have to get it back to normal ?

Please Help me ?

Thank you very much !

You would find more help at the Freaktab forum. Perhaps flash with original firmware

tananhcctv · Feb 26th 2020

Quote from bubblegum57

You would find more help at the Freaktab forum. Perhaps flash with original firmware

Thank you ! My box is currently not connected to the cable to update to another version

Code

tananhcctv · Feb 28th 2020

I HAVE SUCCESSFULLY UNDER THIS TOPIC

[ROM] "GENERIC" SC v1 USER/USERDEBUG - S905x2 / S905x3 - AndroidTV Build - FreakTab

How install LE on bricked box?

Similar Threads

[8.2.4.1] LibreELEC Kodi Krypton - S905 & S912 devices

[8.90.1] CoreELEC for S905/S912 devices