Out of interest Armbian decompiled a the t82x libGLES_mali.so for ubuntu. Is it usable for LibreElec
[8.2.2.3] LibreELEC 8.2 for S912
-
kszaq -
March 3, 2017 at 7:18 PM -
Thread is Unresolved
-
-
I tested the new Alphapreview4 on my Mecool BB2 Pro.
It works great. No wi-fi problems posted some days ago. Maybe there was a problem with my Wi-Fi. Or you have fix something.
I'll test it more in the next days.Thanks kszaq for your work.
Magnum
-
Evolveo H8 (AArch64)
With the SD card is able for the first boot, the other boots are simple, with card LibreELEC goes, without card goes Android. The program is completely unusable unfortunately still falls very often and at very short intervals, less than 3 minutes.
My tests:
Dolby Digital 5.1,7.1,THD 7.1 - OK passtrough
Dolby Digital+7.1 - only silence (Archos plays it very well)
DTS all is OK passtrough, Incredibly, a big compliment to the author
change display resolution goes very well !!!!!
HEVC,4k all OK. HDR I do not know.The program no crashed, it restart itself in very short intervals. I have no function with remote control, I can use only mouse (right click is back ????)
I copied "remote.conf" from etc to root of SDCard but it does nothing.
Very good start for 912.
-
Evolveo H8 (AArch64)With the SD card is able for the first boot, the other boots are simple, with card LibreELEC goes, without card goes Android. The program is completely unusable unfortunately still falls very often and at very short intervals, less than 3 minutes.
My tests:
Dolby Digital 5.1,7.1,THD 7.1 - OK passtrough
Dolby Digital+7.1 - only silence (Archos plays it very well)
DTS all is OK passtrough, Incredibly, a big compliment to the author
change display resolution goes very well !!!!!
HEVC,4k all OK. HDR I do not know.The program no crashed, it restart itself in very short intervals. I have no function with remote control, I can use only mouse (right click is back ????)
I copied "remote.conf" from etc to root of SDCard but it does nothing.
Very good start for 912.
I think the remote.conf goes into /storage/.config
-
In system/settings resolution, I could see two resolutions 1920x1080p ?
Which one are we suppose to use ?One for 50 Hz and one for 60 Hz. You can use any of them.
[hr]
I think the remote.conf goes into /storage/.configIt can find it in the root in the second pass of checking.
I found another possible source of problems:
my remote conf (from android) contains 6 remote data block, and LE (or Kodi) can handle only the last one and if your remote is not the last in the structure then it will not work.The structure is:
Code
Display More#amlogic NEC remote work_mode = 0 repeat_enable = 1 repeat_delay = 130 repeat_peroid = 120 release_delay = 20 debug_enable = 1 fn_key_scancode = 0x15 left_key_scancode = 0x1c right_key_scancode = 0x48 up_key_scancode = 0x44 down_key_scancode = 0x1d ok_key_scancode = 0x1e pageup_key_scancode = 0x04 pagedown_key_scancode = 0x1b custom_begin factory_infcode = 0 factory_code = 0xfb040001 mouse_begin ... mouse_end key_begin ... key_end repeat_key_begin ... repeat_key_end custom_end custom_begin factory_infcode = 1 factory_code = 0xfb000001 mouse_begin ... mouse_end key_begin ... key_end repeat_key_begin ... repeat_key_end custom_end custom_begin factory_infcode = 2 factory_code = ... ... custom_end custom_begin factory_infcode = 3 factory_code = ... ... custom_end ...
If I delete all the custom blocks but keep the one with the right factory code then it works. Also works if I move the right custom block to the end of the list.
-
What about force rgb mode in this alpha build?
I see this file but with strange permissions:
--w--w---- 1 root root 4096 Mar 16 21:55 output_rgb
LibreELEC:/sys/devices/virtual/amhdmitx/amhdmitx0 # cat output_rgb
cat: read error: Input/output errorAnd this code below in autostart.sh doesn't work too:
-
What about force rgb mode in this alpha build?I see this file but with strange permissions:
--w--w---- 1 root root 4096 Mar 16 21:55 output_rgb
LibreELEC:/sys/devices/virtual/amhdmitx/amhdmitx0 # cat output_rgb
cat: read error: Input/output errorAnd this code below in autostart.sh doesn't work too:
It worked for me.
Magnum
-
It can find it in the root in the second pass of checking.
I found another possible source of problems:
my remote conf (from android) contains 6 remote data block, and LE (or Kodi) can handle only the last one and if your remote is not the last in the structure then it will not work.Please help me.
1. When I booted into Android, I can not find /storage/.config (hidden folder), when I booted to LE, I have no access into my box from PC.
2. Below is my remote.conf, from root of SDCard. Could you edit it, how do you think remote could work ?
Code
Display More#********************************************************************************************************* #this file is configuration for each factory remote device # work_mode 0 :software mode 1 :hardware mode # repeat_enable 0 :disable repeat 1 :enable repeat # # factory_code each device has it's unique factory code. # pattern:custom_code(16bit)+index_code(16bit) # examble: 0xff000001 = 0xff00(custom cod) 0001 (index) # # release_delay unit:ms.release will report from kernel to user layer after this period of time # from press or repeat triggered. # # debug_enable 0 :debug disable 1 :debug disable # # SW MODE: # bit_count how many bits in each frame # tw_leader_act time window for leader active # tw_bit0 time window for bit0 time. # tw_bit1 time window for bit1 time # tw_repeat_leader time window for repeat leader # REG # reg_base_gen set value for PREG_IR_DEC_BASE_GEN # reg_control set value for PREG_IR_DEC_CONTROL # reg_leader_act set value for PREG_IR_DEC_LEADER_ACTIVE # reg_leader_idle set value for PREG_IR_DEC_LEADER_IDLE # reg_repeat_leader set value for PREG_IR_DEC_REPEAT_IDLE # reg_bit0_time set value for PREG_IR_DEC_BIT0_TIME #************************************************************************************************************* #amlogic NEC remote work_mode = 0 repeat_enable = 1 repeat_delay = 200 repeat_peroid = 200 release_delay = 10 debug_enable = 1 fn_key_scancode = 0x17 left_key_scancode = 0x47 right_key_scancode = 0x15 up_key_scancode = 0x46 down_key_scancode = 0x16 ok_key_scancode = 0x55 pageup_key_scancode = 0x04 pagedown_key_scancode = 0x1b custom_begin factory_infcode = 0 factory_code = 0xff000001 mouse_begin 0 0x47 1 0x15 2 0x46 3 0x16 mouse_end key_begin 0x18 116 0x54 2 0x48 3 0x7 4 0x50 5 0x12 6 0x11 7 0x4c 8 0xe 9 0xd 10 0xc 11 0x6 102 0x46 103 0x40 158 0x47 105 0x55 97 0x15 106 0x4 139 0x16 108 0x17 140 0x14 114 0x10 115 0x42 119 0x22 75 0x08 76 0x3c 70 0x4f 77 0x56 64 0x57 119 0x1f 14 0x5b 65 0x19 113 key_end repeat_key_begin 0x18 116 0x54 2 0x48 3 0x7 4 0x50 5 0x12 6 0x11 7 0x4c 8 0xe 9 0xd 10 0xc 11 0x6 102 0x46 103 0x40 158 0x47 105 0x55 97 0x15 106 0x4 139 0x16 108 0x17 140 0x14 114 0x10 115 0x42 119 0x22 75 0x08 76 0x3c 70 0x4f 77 0x56 64 0x57 119 0x1f 14 0x5b 65 0x19 113 repeat_key_end custom_end custom_begin factory_infcode = 1 factory_code = 0xbd020001 key_begin 0xca 103 0xd2 108 0x99 105 0xc1 106 0xce 97 0x45 116 0xc5 133 0x80 113 0xd0 15 0xd6 125 0x95 102 0xdd 104 0x8c 109 0x89 131 0x9c 130 0x9a 120 0xcd 121 key_end custom_end
-
1. When I booted into Android, I can not find /storage/.config (hidden folder), when I booted to LE, I have no access into my box from PC.When running libreelec, the config directory is accessible by SMB share (directory name "Configfiles") or through ssh (cd .config). Check Libreelec settings to enable samba and ssh server.
-
Please help me.
1. When I booted into Android, I can not find /storage/.config (hidden folder), when I booted to LE, I have no access into my box from PC.
2. Below is my remote.conf, from root of SDCard. Could you edit it, how do you think remote could work ?As mmp wrote you need to put your remote.conf file to \\LibreElec\Configfiles (SMB share from win) or .config if you login with ssh.
Your remote.conf contains two remote control setup, you should check your remote controls factory code so you know which one do you keep in the conf file.
For checking login to the box with ssh (root/libreelec) then press a button on your remote then type dmesg command and see the last line.
There will be an error message about wrong factory code and an 8 digit hexadecimal number which has the factory code at the last 4 digits (it will ff00 or bd02 according to you remote.conf). I guess that is ff00 so modify your remote.conf as this:Code
Display More#********************************************************************************************************* #this file is configuration for each factory remote device # work_mode 0 :software mode 1 :hardware mode # repeat_enable 0 :disable repeat 1 :enable repeat # # factory_code each device has it's unique factory code. # pattern:custom_code(16bit)+index_code(16bit) # examble: 0xff000001 = 0xff00(custom cod) 0001 (index) # # release_delay unit:ms.release will report from kernel to user layer after this period of time # from press or repeat triggered. # # debug_enable 0 :debug disable 1 :debug disable # # SW MODE: # bit_count how many bits in each frame # tw_leader_act time window for leader active # tw_bit0 time window for bit0 time. # tw_bit1 time window for bit1 time # tw_repeat_leader time window for repeat leader # REG # reg_base_gen set value for PREG_IR_DEC_BASE_GEN # reg_control set value for PREG_IR_DEC_CONTROL # reg_leader_act set value for PREG_IR_DEC_LEADER_ACTIVE # reg_leader_idle set value for PREG_IR_DEC_LEADER_IDLE # reg_repeat_leader set value for PREG_IR_DEC_REPEAT_IDLE # reg_bit0_time set value for PREG_IR_DEC_BIT0_TIME #************************************************************************************************************* #amlogic NEC remote factory_code = 0xff000001 work_mode = 0 repeat_enable = 1 repeat_delay = 200 repeat_peroid = 200 release_delay = 10 debug_enable = 1 fn_key_scancode = 0x17 left_key_scancode = 0x47 right_key_scancode = 0x15 up_key_scancode = 0x46 down_key_scancode = 0x16 ok_key_scancode = 0x55 pageup_key_scancode = 0x04 pagedown_key_scancode = 0x1b mouse_begin 0 0x47 1 0x15 2 0x46 3 0x16 mouse_end key_begin 0x18 116 0x54 2 0x48 3 0x7 4 0x50 5 0x12 6 0x11 7 0x4c 8 0xe 9 0xd 10 0xc 11 0x6 102 0x46 103 0x40 158 0x47 105 0x55 97 0x15 106 0x4 139 0x16 108 0x17 140 0x14 114 0x10 115 0x42 119 0x22 75 0x08 76 0x3c 70 0x4f 77 0x56 64 0x57 119 0x1f 14 0x5b 65 0x19 113 key_end repeat_key_begin 0x18 116 0x54 2 0x48 3 0x7 4 0x50 5 0x12 6 0x11 7 0x4c 8 0xe 9 0xd 10 0xc 11 0x6 102 0x46 103 0x40 158 0x47 105 0x55 97 0x15 106 0x4 139 0x16 108 0x17 140 0x14 114 0x10 115 0x42 119 0x22 75 0x08 76 0x3c 70 0x4f 77 0x56 64 0x57 119 0x1f 14 0x5b 65 0x19 113 repeat_key_end
-
I noticed it doesn't say experimental in the header anymore does that mean the proper fbdev Mali libraries were found or?
-
Latest version indicator.
-
It worked for me.Magnum
How did you check if it worked?
-
Three movies and nothing green screen.
Before applying the patch after a while green screen.Anyway when I saw green screen the first time I tried the echo command via Putty and Tv goes to normal.
Magnum
-
Problems with remote control are solved.
Thanks to Pelican and mmpp too.
I think the stability of the system without a mouse is a bit better but still are spontaneously rebooting Kodi.
-
I'm afraid that as long as we have to use libhybris I cannot help much with the resets. I have spent a lot of time trying to fix this with no success.
-
I'm afraid that as long as we have to use libhybris I cannot help much with the resets. I have spent a lot of time trying to fix this with no success.Could we help with anything?
Logs, uart debug, etc? -
I can reproduce crashes with my box, so logs are not needed.
Only native fbdev (or X11) library would help I'm afraid.
-