How to delay activation of HDMI-video-output?

1st Official Post

    Hello. My Logitech Harmony Touch switches the Raspberry with LibreELEC and my home-theatre-system at the same time on. For some reason I don't get any video nor audio. When I restart Kodi all works fine. I also tried to delay the activation of the Raspberry for some seconds and this did also work. So, if I can delay LibreELEC for some seconds, before HDMI gets activated, this would probably solve my problem. Delaying the start of Kodi by creating an "autostart.sh" did not help. How can I do this?

    Thanks in advance!

    • Official Post
    Quote from raini


    For some reason I don't get any video nor audio.

    It does make me wonder what was in your autostart.sh that didn't work/help.
    If you turn on your HTPC first and then your TV, you probably end up having a problem with the HDMI handshake, because EDID info is lacking in the HTPC. Putting an EDID info file onto your htpc could help.

    Quote from Klojum

    It does make me wonder what was in your autostart.sh that didn't work/help.
    If you turn on your HTPC first and then your TV, you probably end up having a problem with the HDMI handshake, because EDID info is lacking in the HTPC. Putting an EDID info file onto your htpc could help.

    My autostart.sh contained just:
    Sleep=10
    But this did not avoid the activation of HDMI sending the outputs of the bootprocess to my TV.
    [hr]

    Quote from infinity85


    You can specify a delay in Harmony Configuration for your Raspberry. Just insert 5s there or so and it will send the power on signal delayed by this time.

    Initially this was my first idea and preference. So I increased the start-delay of the Raspberry without any improvement. After investigating it appears that the delay is the time between the on-signal and the first command like setting the input. The configuration-tool did not help either. Between the on-commands of the devices no delay possible. Only before additional commands.

    Edited once, last by raini (November 22, 2016 at 7:10 PM).

    Quote from raini

    Initially this was my first idea and preference. So I increased the start-delay of the Raspberry without any improvement. After investigating it appears that the delay is the time between the on-signal and the first command like setting the input. The configuration-tool did not help either. Between the on-commands of the devices no delay possible. Only before additional commands.


    It is hard to find in the harmony software respectively on myharmony.com or whatever you use for programming. I've captured how to find the setting:

    External Content youtu.be
    Content embedded from external sources will not be displayed without your consent.
    Through the activation of external content, you agree that personal data may be transferred to third party platforms. We have provided more information on this in our privacy policy.

    I own an old Harmony 900 remote, so I have to use the old software. I assume you are using the myharmony.com website for programming, but the menus are quite similar. Perhaps you can find this setting there as well :)

    Quote from infinity85


    You can specify a delay in Harmony Configuration for your Raspberry. Just insert 5s there or so and it will send the power on signal delayed by this time.

    Thanks infinity85!
    Do you mean what's described on this page: Fixing Power-on Delays? If yes, this does NOT delay the start but creates a pause in order to make sure that the device had enough time to receive additional commands. If not, where do you set this? On the remote or in the configuration-tool?

    Quote from raini

    Thanks infinity85!
    Do you mean what's described on this page: Fixing Power-on Delays? If yes, this does NOT delay the start but creates a pause in order to make sure that the device had enough time to receive additional commands. If not, where do you set this? On the remote or in the configuration-tool?


    Have you watched my uploaded video? ;)
    It is not that what you described, it is really about a command (in your case power-on) to be sent delayed by an amount of time. Just watch the youtube video I made and linked for you in my last post. :)

    Quote from infinity85


    Have you watched my uploaded video? ;)
    It is not that what you described, it is really about a command (in your case power-on) to be sent delayed by an amount of time. Just watch the youtube video I made and linked for you in my last post. :)


    Thanks a lot for your effort, infinity85. I was not aware of this reply.
    So, this looks exactly the same as what I found in the web-based-tool. What you are doing is the insertion of a delay but this delay cannot be moved so that it is carried out before the startup of the device. So the next action that is not part of your video is to remove the initial startup-acton and insert it after the delay. Is this what you mean? As I cannot remove the initial startup-action I probably must remove the Raspberry from this activity first. I will try this tonight.

    Yes that would be some kind of workaround. I remember doing something similar to my tv.

    What you could do though is: You leave the raspberry set in Harmony software as "leave always on" and then you simply specify a delayed power on action for "when you enter this activity" and a power off action for "when you leave this activity" like at this timestamp of my video:

    External Content youtu.be
    Content embedded from external sources will not be displayed without your consent.
    Through the activation of external content, you agree that personal data may be transferred to third party platforms. We have provided more information on this in our privacy policy.
    . At the top there is before of activity, at bottom it is after activity. So basically its the same as the power on power off routine of Harmony software, but you set it manually. I hope it is understandable.

    EDIT

    Quote from raini


    So the next action that is not part of your video is to remove the initial startup-acton and insert it after the delay. Is this what you mean? As I cannot remove the initial startup-action I probably must remove the Raspberry from this activity first. I will try this tonight.


    Yes perhaps that would be even better :). You can play with it, unless somebody gives a better advice ;)

    Edited once, last by infinity85 (November 23, 2016 at 2:54 PM).

    Many thanks for all replies! I tested the solution of infinity85 and this works. But I also tested the solution with the delay-setting in config.txt which according to the Raspberry-site is especially implemented for my purpose and this works either. As I had to add a line to this file anyway as being part of the remote-configuration I chose this a my solution. So...problem solved!
    Thanks again!