Irtrans remote not recognized on LibreELEC-RR 10

Bobsofa · April 4, 2021 at 10:51 PM

Hello,

I've recently switched from Lubuntu to LibreELEC-RR 10 Generic.x86_64 and everything besides the remote control works.

My system:

Case: Originae S16V with integrated VF210 VFD and IR sensor from Irtrans

CPU: i5-4440

MB: ASUS B85M-G [C2]

RAM: 4GB DDR3

GPU: GTX 1050

TV card: Digital Devices cineS2 V7A

The system has been running with multiple OSs (Win 7, Linux) and the remote worked every time (Linux took a while to set up, but it worked fine for years).

I've tried this thread but the setup doesn't work (some aspects don't make sense with the current LE version, as some files/code lines aren't there) and the irtrans server doesn't seem to load the driver (logs).

I've tried the built-in solution, but every single keytable has the error "No devices found", as has the ir-keytable by itself. lsusb finds the module.

/usr/lib/udev/rc_keymaps/protocols # lsusb

Bus 002 Device 008: ID 046d:c714 Logitech, Inc. diNovo Edge Keyboard

Bus 002 Device 007: ID 046d:c713 Logitech, Inc. Logitech BT Mini-Receiver

Bus 002 Device 006: ID 046d:0b04 Logitech, Inc. Logitech BT Mini-Receiver

Bus 002 Device 005: ID 046d:c525 Logitech, Inc. MX Revolution Cordless Mouse

Bus 002 Device 004: ID 1a40:0101 Terminus Technology Inc. Hub

Bus 002 Device 003: ID 05e3:0608 Genesys Logic, Inc. Hub

Bus 002 Device 002: ID 8087:8000 Intel Corp. Integrated Rate Matching Hub

Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

Bus 001 Device 004: ID 05e3:070e Genesys Logic, Inc. USB 2.0 Card Reader

Bus 001 Device 005: ID 0403:fc60 Future Technology Devices International, Ltd IRTrans USB

Bus 001 Device 003: ID 05e3:0608 Genesys Logic, Inc. Hub

Bus 001 Device 002: ID 8087:8008 Intel Corp. Integrated Rate Matching Hub

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

but no approach has worked so far. What am I doing wrong? My Linux experience is limited and I've run out of ideas . It would be a shame to abandon the build after everything else is working as expected .

Thank you for your help.

Bobsofa · April 9, 2021 at 2:44 PM

Is there any way I could help to give more info? Can I use the drivers from the previous Linux install to fix this (I have backups of both LE and Lubuntu)?

**heitbaum** · April 9, 2021 at 11:04 PM

Code

Apr 04 20:20:32.259050 HTPC kernel: usbcore: registered new interface driver ftdi_sio
Apr 04 20:20:32.259086 HTPC kernel: usbserial: USB Serial support registered for FTDI USB Serial Device
Apr 04 20:20:32.259099 HTPC kernel: ftdi_sio 1-1.5.1:1.0: FTDI USB Serial Device converter detected
Apr 04 20:20:32.259255 HTPC kernel: usb 1-1.5.1: Detected FT232RL
Apr 04 20:20:32.262619 HTPC kernel: usb 1-1.5.1: FTDI USB Serial Device converter now attached to ttyUSB0

Code

Apr 04 20:21:02.981781 HTPC systemd[1]: service.lcdd.service: Scheduled restart job, restart counter is at 4.
Apr 04 20:21:02.982293 HTPC systemd[1]: Stopped LCDProc.
Apr 04 20:21:02.984274 HTPC systemd[1]: Started LCDProc.
Apr 04 20:21:02.992908 HTPC sh[1066]: LCDd 0.5dev, LCDproc Protocol 0.4
...
Apr 04 20:21:02.995331 HTPC sh[1066]: irtrans: unable to init client socket
Apr 04 20:21:02.995331 HTPC sh[1066]: Driver [irtrans] init failed, return code -1
Apr 04 20:21:02.995331 HTPC sh[1066]: Could not load driver irtrans
Apr 04 20:21:02.995410 HTPC sh[1066]: There is no output driver
Apr 04 20:21:02.995410 HTPC sh[1066]: Critical error while initializing, abort.
Apr 04 20:21:02.995743 HTPC systemd[1]: service.lcdd.service: Main process exited, code=exited, status=1/FAILURE
Apr 04 20:21:02.995853 HTPC systemd[1]: service.lcdd.service: Failed with result 'exit-code'.
Apr 04 20:21:03.527916 HTPC systemd[1]: systemd-hostnamed.service: Succeeded.
Apr 04 20:21:08.231772 HTPC systemd[1]: service.lcdd.service: Scheduled restart job, restart counter is at 5.
Apr 04 20:21:08.232308 HTPC systemd[1]: Stopped LCDProc.
Apr 04 20:21:08.232358 HTPC systemd[1]: service.lcdd.service: Start request repeated too quickly.
Apr 04 20:21:08.232377 HTPC systemd[1]: service.lcdd.service: Failed with result 'exit-code'.
Apr 04 20:21:08.232817 HTPC systemd[1]: Failed to start LCDProc.

Display More

Looking at the logs this is what I can see. Is the RT232RL your ir receiver?

What does lsusb -t and lsusb -v show? Where / have you configured the ttyUSB0?

ghtester · April 10, 2021 at 1:50 AM

Try to run the irserver manually:

irserver -loglevel 4 -debug_code /dev/ttyUSB0

Bobsofa · April 10, 2021 at 12:59 PM

Quote from heitbaum

Looking at the logs this is what I can see. Is the RT232RL your ir receiver?

After researching it: Yes, the RT232RL is the ir receiver built into my case.

Code

lsusb -t
/:  Bus 02.Port 1: Dev 1, Class=root_hub, Driver=ehci-pci/2p, 480M
    |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/6p, 480M
        |__ Port 3: Dev 3, If 0, Class=Hub, Driver=hub/4p, 480M
        |__ Port 4: Dev 4, If 0, Class=Hub, Driver=hub/4p, 480M
            |__ Port 3: Dev 7, If 3, Class=Application Specific Interface, Driver=, 12M
            |__ Port 3: Dev 7, If 1, Class=Vendor Specific Class, Driver=btusb, 12M
            |__ Port 3: Dev 7, If 2, Class=Vendor Specific Class, Driver=btusb, 12M
            |__ Port 3: Dev 7, If 0, Class=Vendor Specific Class, Driver=btusb, 12M
            |__ Port 1: Dev 5, If 0, Class=Iuman Interface Device, Driver=usbhid, 12M
            |__ Port 1: Dev 5, If 1, Class=Iuman Interface Device, Driver=usbhid, 12M
            |__ Port 2: Dev 6, If 0, Class=Hub, Driver=hub/3p, 12M
                |__ Port 3: Dev 9, If 0, Class=Iuman Interface Device, Driver=usbhid, 12M
                |__ Port 2: Dev 8, If 0, Class=Iuman Interface Device, Driver=usbhid, 12M
/:  Bus 01.Port 1: Dev 1, Class=root_hub, Driver=ehci-pci/2p, 480M
    |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/6p, 480M
        |__ Port 5: Dev 3, If 0, Class=Hub, Driver=hub/4p, 480M
            |__ Port 1: Dev 5, If 0, Class=Vendor Specific Class, Driver=ftdi_sio, 12M
        |__ Port 6: Dev 4, If 0, Class=Mass Storage, Driver=usb-storage, 480M

Display More

Since -v led to too many lines for putty, I've printed only the IrTrans device.

Code

HTPC:~ # lsusb -v -d 0403:

Bus 001 Device 005: ID 0403:fc60 Future Technology Devices International, Ltd IRTrans USB
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0         8
  idVendor           0x0403 Future Technology Devices International, Ltd
  idProduct          0xfc60
  bcdDevice            6.00
  iManufacturer           1 MConsult
  iProduct                2 IRTrans USB
  iSerial                 3 MMUN0000
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength       0x0020
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0x80
      (Bus Powered)
    MaxPower               50mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass    255 Vendor Specific Subclass
      bInterfaceProtocol    255 Vendor Specific Protocol
      iInterface              2 IRTrans USB
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               0
can't get device qualifier: Resource temporarily unavailable
can't get debug descriptor: Resource temporarily unavailable
Device Status:     0x0000
  (Bus Powered)

Display More

Quote from heitbaum

Where / have you configured the ttyUSB0?

I'm sorry, I don't know where and how to do that. I'm a Linux noob, especially with Libreelec.

Quote from ghtester

Try to run the irserver manually:
irserver -loglevel 4 -debug_code /dev/ttyUSB0

Code

HTPC:~ # irserver -loglevel 4 -debug_code /dev/ttyUSB0
-sh: irserver: not found

Thank you for your help.

ghtester · April 10, 2021 at 3:53 PM

You need to follow the instructions from thread you mentioned above.

Start here: RE: irserver add-on

You need to obtain the necessary files from this package or an alternative files from OpenELEC as apa explained.

For the original irserver installation to /storage/.config/irtrans/ folder, try copy & paste these commands to SSH console:

Code

cd /tmp
wget -c http://www.irtrans.de/download/Server/Linux/irserver.tar.gz
tar -xf irserver.tar.gz
sed -i 's+/usr/local/+/storage/.config/+g' install.sh
./install.sh

Then try to run it manually to see if it's doing something:

/storage/.config/irtrans/irserver -loglevel 4 -debug_code /dev/ttyUSB0

If it works, you may try to put the startup line to /storage/.config/autostart.sh file, which could perhaps be something like:

/storage/.config/irtrans/irserver -logfile /var/log/irserver.log -pidfile /var/run/irserver.pid -daemon /dev/ttyUSB0

If you get the irserver running, then you need to finish the remaining instructions from this and next posts, starting from this point:

Instruct Kodi to listen on the alternate LIRC socket (/run/lirc/lircd.itrans) by changing the Kodi command-line parameter with which it is launched.

I don't have this hardware so you have to give it a try.

Bobsofa · April 10, 2021 at 5:56 PM

Code

HTPC:~/.config # cd /tmp
HTPC:/tmp # tar -xf irserver.tar.gz
HTPC:/tmp # sed -i 's+/usr/local/+/storage/.config/+g' install.sh
HTPC:/tmp # ./install.sh
IRTrans Software installed in /storage/.config/irtrans

After a reboot

Code

HTPC:~ # /storage/.config/irtrans/irserver -loglevel 4 -debug_code /dev/ttyUSB0
-sh: /storage/.config/irtrans/irserver: not found

I can see the folder and the file, it just doesn't work

Code

HTPC:~/.config/irtrans # ls
ip_assign    irclient     irserver     remotes
ip_assign64  irclient64   irserver64
HTPC:~/.config/irtrans # chmod +x irserver
HTPC:~/.config/irtrans # irserver -loglevel 4 -debug_code /dev/ttyUSB0
-sh: irserver: not found
HTPC:~/.config/irtrans #

The folder /run/lirc/lircd.itrans doesn't exist, but I guess it's because the irserver doesn't get of the ground.

If I follow the post past this I encounter other issues:

-The file the post points to (irserver-src.tar.gz), doesn't contain the server executable and install script, so I used the package you suggested.

-"Instruct Kodi to listen on the alternate LIRC socket (/run/lirc/lircd.itrans) by changing the Kodi command-line parameter with which it is launched.

To do this, copy /usr/lib/kodi/kodi-config to /storage/.config/. Edit /storage/.config/kodi-config and replace the line reading KODI_ARGS="--lircdev /run/lirc/lircd" with the following"

This line "KODI_ARGS="--lircdev /run/lirc/lircd" doesn't exist in the file kodi-config

Display Spoiler

#!/bin/sh

# SPDX-License-Identifier: GPL-2.0-or-later

KODI_ROOT=$HOME/.kodi

BOOT_STATE="$(cat $HOME/.config/boot.status 2>/dev/null)"

# May not exist if testing a clean /storage/.kodi without rebooting

mkdir -p $KODI_ROOT/userdata

# hack: make addon-bins executable

# done in kodi on addon install. but just in case..

chmod +x $KODI_ROOT/addons/*/bin/* 2>/dev/null

# setup Kodi sources

if [ ! -f $KODI_ROOT/userdata/sources.xml ]; then

if [ -f /usr/share/kodi/config/sources.xml ]; then

cp /usr/share/kodi/config/sources.xml $KODI_ROOT/userdata

fi

# common setup guisettings

if [ ! -f $KODI_ROOT/userdata/guisettings.xml ] ; then

if [ -f /usr/share/kodi/config/guisettings.xml ]; then

cp /usr/share/kodi/config/guisettings.xml $KODI_ROOT/userdata

fi

if [ "$BOOT_STATE" = "SAFE" ]; then

[ ! -f $KODI_ROOT/userdata/guisettings.xml ] && echo '<settings version="2"></settings>' > $KODI_ROOT/userdata/guisettings.xml

xmlstarlet ed --omit-decl --inplace -s settings -t elem -n setting -v "maroon" -i settings/setting -t attr -n id -v lookandfeel.skin>

fi

KODI_ARGS=""

echo "KODI_ARGS=\"$KODI_ARGS\"" > /run/libreelec/kodi.conf

if [ "$(uname -m)" = "x86_64" ]; then

echo "MALLOC_MMAP_THRESHOLD_=524288" >> /run/libreelec/kodi.conf

else #arm

echo "MALLOC_MMAP_THRESHOLD_=8192" >> /run/libreelec/kodi.conf

fi

if [ -f /storage/.config/kodi.conf ] ; then

cat /storage/.config/kodi.conf >>/run/libreelec/kodi.conf

fi

Current logs don't even show the server.

Thank you for your help.

ghtester · April 10, 2021 at 7:14 PM

Quote from Bobsofa

HTPC:~/.config/irtrans # irserver -loglevel 4 -debug_code /dev/ttyUSB0

This is wrong. If you try to run it inside the folder, you have to enter ./irserver

That's why I put the example with absolute path which must work ( /storage/.config/irtrans/irserver )

Otherwise you have an issue with SSH client or a filesystem issue.

The source codes needs to be compiled. The better option should be to get the necessary files from OpenELEC package.

Bobsofa · April 10, 2021 at 8:28 PM

Quote from ghtester

This is wrong. If you try to run it inside the folder, you have to enter ./irserver
That's why I put the example with absolute path which must work ( /storage/.config/irtrans/irserver )
Otherwise you have an issue with SSH client or a filesystem issue.
The source codes needs to be compiled. The better option should be to get the necessary files from OpenELEC package.

Afair, when I use the full command, the result is the same (The machine is currently in use with an older Linux image. When I have the time to put the LE image back on, I will confirm this).

I tried to obtain the OE files. The newest image from the website seems to be faulty (It installs, but upon reboot I get a "OS missing" message. I tried it multiple times with the same result) and I can't find an older version. Is there some server where these files are downloadable?

Thank you for your help.

**mglae** · April 10, 2021 at 9:50 PM

Most likely you have to use irserver64 on a 64 bit system.

Bobsofa · April 11, 2021 at 3:02 AM

Quote from mglae

Most likely you have to use irserver64 on a 64 bit system.

Thank you so much, now the server starts. I missed the forest for the trees. And I even see button presses.

Code

HTPC:/tmp # /storage/.config/irtrans/irserver64 -loglevel 4 -debug_code /dev/tty
USB0
Init Server Socket done
IRServer64 Version 6.10.23
Init Events done
Opening Device: /dev/ttyUSB0
IRTRans Send Done: 1
Name   :
Version: D5.08.09
FW SNo : 14485
Capab  : Power On;
FW Cap : 0x3c8019
USB SNo:
Node   : /dev/ttyUSB0

Init communication ...
[ 0]:                      D5.08.09     SN: 14485
Chdir to DB OK
Read routing OK
Read Switches OK
Open DIR: 12
Get Dirent: 512
**** CCF Error: ac1 [Remote: ccf.rem]
Remote ccf                  compiled:    20 Timings -     20 Commands
Remote mce-keyboard         compiled:     1 Timings -     77 Commands
Remote mce-mouse            compiled:     1 Timings -      1 Commands
Remote irtrans              compiled:     1 Timings -     33 Commands
Remote sky-hd               compiled:     1 Timings -     34 Commands
Remote sky-digital          compiled:     1 Timings -     31 Commands
Remote mediacenter          compiled:     1 Timings -     49 Commands
Remote pace                 compiled:     2 Timings -     38 Commands
Remote dbox2                compiled:     1 Timings -     26 Commands
Remote kathrein-ufs         compiled:     2 Timings -     36 Commands
Remote dream                compiled:     0 Timings -     36 Commands
Get Dirent: 0
Duplicate Commands for ccf.1:   ccf.2  ccf.3  ccf.4
Duplicate Commands for ccf.2:   ccf.3  ccf.4
Duplicate Commands for ccf.3:   ccf.4
Duplicate Commands for pace.0:   pace.0-
Total:  11 Remotes  -  31 Timings -  381 Commands -    0 Calib. Commands
         0 Togglec. -  19 CCF Data -   0 CCF RAW  -    1 CCF Error
IRTRans Send Done: 1
IRTRans Send Done: 1
Select Return: 0
Select Return: 1
Select Return: 0
Select Return: 1
Select Return: 1
[0.0]: LEN: 34  S001000001101111101100000100111110
Select Return: 1
[0.0]: LEN: 34  S001000001101111101100000100111110
Select Return: 1
[0.0]: LEN: 34  S001000001101111101100000100111110
Select Return: 1
[0.0]: LEN: 34  S001000001101111101100000100111110
Select Return: 1
[0.0] right mediacenter
Select Return: 1
[0.0] right mediacenter
Select Return: 1
[0.0] left mediacenter
Select Return: 1
[0.0] left mediacenter
Select Return: 1
[0.0] left mediacenter
Select Return: 1
[0.0] left mediacenter
Select Return: 1
[0.0] left mediacenter
Select Return: 1
[0.0] right mediacenter
Select Return: 1
[0.0] right mediacenter
Select Return: 1
[0.0] right mediacenter
Select Return: 1
[0.0] left mediacenter
Select Return: 1
[0.0] left mediacenter
Select Return: 1
[0.0] left mediacenter
Select Return: 1
[0.0] left mediacenter
Select Return: 1
[0.0] left mediacenter
Select Return: 1
[0.0] right mediacenter
Select Return: 1
[0.0] right mediacenter
Select Return: 1
[0.0] right mediacenter
Select Return: 1
[0.0] right mediacenter
Select Return: 1
[0.0] right mediacenter
Select Return: 1
[0.0] right mediacenter
Select Return: 1
[0.0] right mediacenter
Select Return: 1
[0.0] right mediacenter
Select Return: 0
Select Return: 1
Select Return: 0
Select Return: 1
^CIRTRans Send Done: 1
IRTRans Send Done: 1

Display More

However, I don't have a lircd.itrans file.

Code

HTPC:/run/lirc # ls
lircd         lircd.socket

Is this one of the files I would need from Openeelec?

Thank you for your help.

ghtester · April 11, 2021 at 5:34 AM

This is not a file but a socket. Read this post again and more carefully until you understand, I can't explain it better. Also keep in mind the post is 4 years old so some things may be different in LE 10.

As described, the original irserver daemon uses the same LIRC socket (/run/lirc/lircd) , the custom irserver daemon from old LibreELEC & OpenELEC uses a different socket (/run/lirc/lircd.irtrans). The difference is explained, I don't know if Kodi can work with original irserver daemon without any changes as apa was using the custom one and therefore described the changes necessary for alternate socket.

You need to test yourself.

Bobsofa · April 11, 2021 at 5:41 PM

Okay, I've successfully copied the OE irserver file from an older working OE image I've found. I've copied it as irserver64 (irserver through the same error as the official IRtrans version) into ~/.config/irtrans/. The ir server seems to be working fine:

Display Spoiler

/storage/.config/irtrans/irserver64 -loglevel 4 -debug_code /dev/ttyUSB

0

Init Server Socket done

IRServer64 Version 6.03.08

Init Events done

Opening Device: /dev/ttyUSB0

IRTRans Send Done: 1

Name :

Version: D5.08.09

FW SNo : 14485

Capab : Power On;

FW Cap : 0x3c8019

USB SNo:

Node : /dev/ttyUSB0

Init communication ...

[ 0]: D5.08.09 SN: 14485

Chdir to DB OK

Read routing OK

Read Switches OK

Open DIR: 12

Get Dirent: 512

**** CCF Error: ac1 [See below for Remote name]

Remote ccf compiled: 20 Timings - 20 Commands

Remote mce-keyboard compiled: 1 Timings - 77 Commands

Remote mce-mouse compiled: 1 Timings - 1 Commands

Remote irtrans compiled: 1 Timings - 33 Commands

Remote sky-hd compiled: 1 Timings - 34 Commands

Remote sky-digital compiled: 1 Timings - 31 Commands

Remote mediacenter compiled: 1 Timings - 49 Commands

Remote pace compiled: 2 Timings - 38 Commands

Remote dbox2 compiled: 1 Timings - 26 Commands

Remote kathrein-ufs compiled: 2 Timings - 36 Commands

Remote dream compiled: 0 Timings - 36 Commands

Get Dirent: 0

Duplicate Commands for ccf.1: ccf.2 ccf.3 ccf.4

Duplicate Commands for ccf.2: ccf.3 ccf.4

Duplicate Commands for ccf.3: ccf.4

Duplicate Commands for pace.0: pace.0-

Total: 11 Remotes - 31 Timings - 381 Commands - 0 Calib. Commands

0 Togglec. - 19 CCF Data - 0 CCF RAW - 1 CCF Error

IRTRans Send Done: 1

[0.0] left mediacenter

[0.0] right mediacenter

[0.0] left mediacenter

[0.0] right mediacenter

[0.0] up mediacenter

[0.0] down mediacenter

[0.0] ok mediacenter

^CIRTRans Send Done: 1

IRTRans Send Done: 1

/storage/.config/autostart.sh looks like this:

Code

echo 1 > /sys/module/bluetooth/parameters/disable_ertm
) &
nohup script.sh &


/storage/.config/irtrans/irserver64 -logfile /var/log/irserver.log -pidfile /var/run/irserver.pid -daemon /dev/ttyUSB0

Is this correct? Now I have the socket described in the post upon reboot.

Code

HTPC:/run/lirc # ls
lircd          lircd.irtrans  lircd.socket

Now to the next problem with the old manual.

Display Spoiler

Instruct Kodi to listen on the alternate LIRC socket (/run/lirc/lircd.itrans) by changing the Kodi command-line parameter with which it is launched.

To do this, copy /usr/lib/kodi/kodi-config to /storage/.config/. Edit /storage/.config/kodi-config and replace the line reading KODI_ARGS="--lircdev /run/lirc/lircd" with the following

Code

if [ -e /run/lirc/lircd.irtrans ]; then
KODI_ARGS="--lircdev /run/lirc/lircd.irtrans"
else
KODI_ARGS="--lircdev /run/lirc/lircd"
fi

This way, Kodi will only listen to /run/lirc/lircd.irtrans if it exists (and fallback to /run/lirc/lircd otherwise). Make sure to make /storage/.config/kodi-config executable (chmod +x kodi-config).

Now copy /usr/lib/systemd/system/kodi.service to /storage/.config/system.d/kodi.service. Modify /storage/.config/system.d/kodi.service and change the line ExecStartPre=-/usr/lib/kodi/kodi-config to ExecStartPre=-/storage/.config/kodi-config. This will instruct LibreElec to launch your custom kodi-config instead of the default one.

or

Display Spoiler

Instead, of the "kodi-config" step from my previous post above, you now need to modify /storage/.config/system.d/kodi.service and add the following line:

Environment="LIRC_SOCKET_PATH=/var/run/lirc/lircd.irtrans"

Add this as the first line in the [Service] domain of kodi.service.

Neither /storage/.config/kodi-config nor /storage/.config/system.d/kodi.service exist in the build of RR. I have a

Code

/.config/system.d/kodi.service.wants # ls
service.rr-config-tool.service

Display Spoiler

[Unit]

Description=RR Config Tool

After=pulseaudio.service

Before=kodi.service

Wants=kodi.service pulseaudio.service

[Service]

ExecStart=/bin/sh /usr/share/kodi/addons/service.rr-config-tool/bin/rr-config-tool.start

Type=oneshot

RemainAfterExit=yes

[Install]

WantedBy=kodi.service pulseaudio.service

In which location is the config file located, where the change of lirc socket needs to made?

Current logs.

Thank you for your help.

**HiassofT** · April 11, 2021 at 8:06 PM

Create a /storage/.config/kodi.conf file with the following line

Code

LIRC_SOCKET_PATH=/var/run/lirc/lircd.irtrans

so long,

Hias

Bobsofa · April 11, 2021 at 8:55 PM

Quote from HiassofT
Create a /storage/.config/kodi.conf file with the following line
Code
LIRC_SOCKET_PATH=/var/run/lirc/lircd.irtrans
so long,
Hias

And now it works. Thank you very much!

ghtester · April 11, 2021 at 10:40 PM

So don't hesitate to EDIT THREAD and Mark as Resolved...