Samsung Remote for rpi 4 media center with libreelec 9.2

  • Hi,

    i used OSMC before, but i bought a rpi 4, which is not yet supported by osmc.

    So i installed libreelec again, setup is ok, tvheadend running.

    I am struggling to setup a Samsung smart TV Remote.

    Is there a step by step guide for dummies ?!

    Regards Mad

    raspberry_pi__lirc_ir_receiver_schaltplan_tsop4838.png


    81ISFjJKWnL._SL1500_.jpg

  • in OSMC you can navigate to config, select a predefined remote and it works, that was the reason why i moved all my rpi media centers from libreelec to osmc.

  • this cant be that hard, dozens of people have ir remotes running.

    when i am connected via,putty the command to test if ir signals are received would help a lot.

  • Not sure if this will help or not but Infrared Remotes [LibreELEC.wiki] it has some information about troubleshooting etc... I'm new to this hardware but was looking at remotes today and read this so I hope this helps, if not good luck and I'll be watching this thread so if you find a solution by all means post it up so I can read up on it.

  • It seems, that the driver is not loaded. ?!?

    HDDREC2020:~ # ir-keytable

    /sys/class/rc/: No such file or directory

    No devices found

    HDDREC2020:~ # cat /proc/bus/input/devices

    I: Bus=0003 Vendor=1a2c Product=0027 Version=0110

    N: Name="USB USB Keykoard"

    P: Phys=usb-0000:01:00.0-1.3/input0

    S: Sysfs=/devices/platform/scb/http://fd500000.pcie/pci0000:00/000…01/input/input0

    U: Uniq=

    H: Handlers=sysrq kbd leds event0

    B: PROP=0

    B: EV=120013

    B: KEY=10000 7 ff800000 7ff febeffdf f3cfffff ffffffff fffffffe

    B: MSC=10

    B: LED=7

    I: Bus=0003 Vendor=1a2c Product=0027 Version=0110

    N: Name="USB USB Keykoard Consumer Control"

    P: Phys=usb-0000:01:00.0-1.3/input1

    S: Sysfs=/devices/platform/scb/http://fd500000.pcie/pci0000:00/000…02/input/input1

    U: Uniq=

    H: Handlers=kbd event1

    B: PROP=0

    B: EV=1f

    B: KEY=300ff 0 0 0 0 483ffff 17aff32d bf544446 0 0 1 130c73 b17c000 267bfa d9415fed 9e1680 4400 0 10000002

    B: REL=40

    B: ABS=1 0

    B: MSC=10

    I: Bus=0003 Vendor=1a2c Product=0027 Version=0110

    N: Name="USB USB Keykoard System Control"

    P: Phys=usb-0000:01:00.0-1.3/input1

    S: Sysfs=/devices/platform/scb/http://fd500000.pcie/pci0000:00/000…02/input/input2

    U: Uniq=

    H: Handlers=kbd event2

    B: PROP=0

    B: EV=13

    B: KEY=c000 100000 0 0 0

    B: MSC=10

    I: Bus=0000 Vendor=0000 Product=0000 Version=0000

    N: Name="lircd-uinput"

    P: Phys=

    S: Sysfs=/devices/virtual/input/input3

    U: Uniq=

    H: Handlers=sysrq kbd event3 rfkill

    B: PROP=0

    B: EV=100003

    B: KEY=ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff fffffffe

    I: Bus=0000 Vendor=0000 Product=0000 Version=0000

    N: Name="eventlircd"

    P: Phys=/dev/input/event3

    S: Sysfs=/devices/virtual/input/input4

    U: Uniq=

    H: Handlers=event4

    B: PROP=0

    B: EV=3

    B: KEY=ff ffffffff 0 0 0 0 f 0 0 0 0 0 0 3ffff 7fff8fff ff03ff 0 0 0 0 0 0 0 0

    HDDREC2020:~ # dmesg

    [ 0.000000] Booting Linux on physical CPU 0x0

    [ 0.000000] Linux version 4.19.83 (jenkins@tsuboi) (gcc version 8.3.0 (GCC)) #1 SMP Sat Nov 23 01:54:59 CET 2019

    [ 0.000000] CPU: ARMv7 Processor [410fd083] revision 3 (ARMv7), cr=30c5383d

    [ 0.000000] CPU: div instructions available: patching division code

    [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache

    [ 0.000000] OF: fdt: Machine model: Raspberry Pi 4 Model B Rev 1.1

    [ 0.000000] Memory policy: Data cache writealloc

    [ 0.000000] cma: Reserved 256 MiB at 0x000000001bc00000

    [ 0.000000] On node 0 totalpages: 442368

    [ 0.000000] DMA zone: 1584 pages used for memmap

    [ 0.000000] DMA zone: 0 pages reserved

    [ 0.000000] DMA zone: 180224 pages, LIFO batch:63

    [ 0.000000] HighMem zone: 262144 pages, LIFO batch:63

    [ 0.000000] random: get_random_bytes called from start_kernel+0xc0/0x4d4 with crng_init=0

    [ 0.000000] percpu: Embedded 17 pages/cpu s37580 r8192 d23860 u69632

    [ 0.000000] pcpu-alloc: s37580 r8192 d23860 u69632 alloc=17*4096

    [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3

    [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 440784

    [ 0.000000] Kernel command line: coherent_pool=1M 8250.nr_uarts=0 cma=64M cma=256M video=HDMI-A-1:1920x1080M@60,margin_left=0,margin_right=0,margin_top=0,margin_bottom=0 smsc95xx.macaddr=DC:A6:32:26:BF:56 vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000 boot=UUID=2311-4421 disk=UUID=4a7717ae-4e4f-431a-86cf-643c8bb8834a quiet root=/dev/ram0 rdinit=/init usbcore.autosuspend=-1

    [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)

    [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)

    [ 0.000000] Memory: 1468232K/1769472K available (10240K kernel code, 753K rwdata, 2236K rodata, 6144K init, 557K bss, 39096K reserved, 262144K cma-reserved, 1048576K highmem)

    [ 0.000000] Virtual kernel memory layout:

    [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)

    [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)

    [ 0.000000] vmalloc : 0xec800000 - 0xff800000 ( 304 MB)

    [ 0.000000] lowmem : 0xc0000000 - 0xec000000 ( 704 MB)

    [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)

    [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)

    [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (12256 kB)

    [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (6144 kB)

    [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 754 kB)

    [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 558 kB)

    [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1

    [ 0.000000] ftrace: allocating 32504 entries in 96 pages

    [ 0.000000] rcu: Hierarchical RCU implementation.

    [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16

    [ 0.000000] GIC: Using split EOI/Deactivate mode

    [ 0.000000] arch_timer: cp15 timer(s) running at 54.00MHz (phys).

    [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xc743ce346, max_idle_ns: 440795203123 ns

    [ 0.000005] sched_clock: 56 bits at 54MHz, resolution 18ns, wraps every 4398046511102ns

    [ 0.000017] Switching to timer-based delay loop, resolution 18ns

    [ 0.000267] Console: colour dummy device 80x30

    [ 0.000301] console [tty0] enabled

    [ 0.000351] Calibrating delay loop (skipped), value calculated using timer frequency.. 108.50 BogoMIPS (lpj=180000)

    [ 0.000380] pid_max: default: 32768 minimum: 301

    [ 0.000571] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)

    [ 0.000594] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)

    [ 0.001361] CPU: Testing write buffer coherency: ok

    [ 0.001881] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000

    [ 0.002695] Setting up static identity map for 0x200000 - 0x20003c

    [ 0.002897] rcu: Hierarchical SRCU implementation.

    [ 0.005518] smp: Bringing up secondary CPUs ...

    [ 0.006588] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001

    [ 0.007795] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002

    [ 0.008942] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003

    [ 0.009110] smp: Brought up 1 node, 4 CPUs

    [ 0.009126] SMP: Total of 4 processors activated (432.00 BogoMIPS).

    [ 0.009139] CPU: All CPU(s) started in HYP mode.

    [ 0.009151] CPU: Virtualization extensions available.

    [ 0.009911] devtmpfs: initialized

    [ 0.020925] VFP support v0.3: implementor 41 architecture 3 part 40 variant 8 rev 0

    [ 0.021161] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns

    [ 0.021188] futex hash table entries: 1024 (order: 4, 65536 bytes)

    [ 0.027929] pinctrl core: initialized pinctrl subsystem

    [ 0.028932] NET: Registered protocol family 16

    [ 0.032895] DMA: preallocated 1024 KiB pool for atomic coherent allocations

    [ 0.033929] cpuidle: using governor ladder

    [ 0.033978] cpuidle: using governor menu

    [ 0.034468] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.

    [ 0.034482] hw-breakpoint: maximum watchpoint size is 8 bytes.

    [ 0.034715] Serial: AMBA PL011 UART driver

    [ 0.039310] bcm2835-mbox fe00b880.mailbox: mailbox enabled

    [ 0.082189] bcm2835-dma fe007000.dma: DMA legacy API manager at (ptrval), dmachans=0x1

    [ 0.085395] vgaarb: loaded

    [ 0.085749] SCSI subsystem initialized

    [ 0.085960] usbcore: registered new interface driver usbfs

    [ 0.086015] usbcore: registered new interface driver hub

    [ 0.086098] usbcore: registered new device driver usb

    [ 0.091417] raspberrypi-firmware soc:firmware: Attached to firmware from 2019-11-05 20:38, variant start_x

    [ 0.093701] raspberrypi-firmware soc:firmware: Firmware hash is 9b5b17690196152a1df1beb1429dd906556d5829

    [ 0.097493] Advanced Linux Sound Architecture Driver Initialized.

    [ 0.098528] clocksource: Switched to clocksource arch_sys_counter

    [ 0.186163] FS-Cache: Loaded

    [ 0.196573] NET: Registered protocol family 2

    [ 0.197167] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)

    [ 0.197198] TCP established hash table entries: 8192 (order: 3, 32768 bytes)

    [ 0.197259] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)

    [ 0.197326] TCP: Hash tables configured (established 8192 bind 8192)

    [ 0.197465] UDP hash table entries: 512 (order: 2, 16384 bytes)

    [ 0.197498] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)

    [ 0.197731] NET: Registered protocol family 1

    [ 0.198395] RPC: Registered named UNIX socket transport module.

    [ 0.198409] RPC: Registered udp transport module.

    [ 0.198421] RPC: Registered tcp transport module.

    [ 0.198434] RPC: Registered tcp NFSv4.1 backchannel transport module.

    [ 0.198454] PCI: CLS 0 bytes, default 64

    [ 0.224022] Initialise system trusted keyrings

    [ 0.224250] workingset: timestamp_bits=14 max_order=19 bucket_order=5

    [ 0.233410] squashfs: version 4.0 (2009/01/31) Phillip Lougher

    [ 0.234149] FS-Cache: Netfs 'nfs' registered for caching

    [ 0.234787] NFS: Registering the id_resolver key type

    [ 0.234851] Key type id_resolver registered

    [ 0.234864] Key type id_legacy registered

    [ 0.234888] nfs4filelayout_init: NFSv4 File Layout Driver Registering...

    [ 0.235422] FS-Cache: Netfs 'cifs' registered for caching

    [ 0.242543] Key type asymmetric registered

    [ 0.242558] Asymmetric key parser 'x509' registered

    [ 0.242751] bounce: pool size: 64 pages

    [ 0.242796] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)

    [ 0.242812] io scheduler noop registered (default)

    [ 0.242825] io scheduler deadline registered

    [ 0.242983] io scheduler cfq registered

    [ 0.242998] io scheduler mq-deadline registered

    [ 0.243012] io scheduler kyber registered

    [ 0.243146] io scheduler bfq registered

    [ 0.247500] brcm-pcie fd500000.pcie: could not get clock

    [ 0.247589] brcm-pcie fd500000.pcie: host bridge /scb/pcie@7d500000 ranges:

    [ 0.247643] brcm-pcie fd500000.pcie: MEM 0x600000000..0x603ffffff -> 0xf8000000

    [ 0.295246] brcm-pcie fd500000.pcie: link up, 5.0 Gbps x1 (!SSC)

    [ 0.295503] brcm-pcie fd500000.pcie: PCI host bridge to bus 0000:00

    [ 0.295521] pci_bus 0000:00: root bus resource [bus 00-01]

    [ 0.295541] pci_bus 0000:00: root bus resource [mem 0x600000000-0x603ffffff] (bus address [0xf8000000-0xfbffffff])

    [ 0.295601] pci 0000:00:00.0: [14e4:2711] type 01 class 0x060400

    [ 0.295830] pci 0000:00:00.0: PME# supported from D0 D3hot

    [ 0.298655] PCI: bus0: Fast back to back transfers disabled

    [ 0.298679] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring

    [ 0.298889] pci 0000:01:00.0: [1106:3483] type 00 class 0x0c0330

    [ 0.298976] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00000fff 64bit]

    [ 0.299226] pci 0000:01:00.0: PME# supported from D0 D3cold

    [ 0.301927] PCI: bus1: Fast back to back transfers disabled

    [ 0.301946] pci_bus 0000:01: busn_res: [bus 01] end is updated to 01

    [ 0.302009] pci 0000:00:00.0: BAR 8: assigned [mem 0x600000000-0x6000fffff]

    [ 0.302031] pci 0000:01:00.0: BAR 0: assigned [mem 0x600000000-0x600000fff 64bit]

    [ 0.302073] pci 0000:00:00.0: PCI bridge to [bus 01]

    [ 0.302098] pci 0000:00:00.0: bridge window [mem 0x600000000-0x6000fffff]

    [ 0.302357] pcieport 0000:00:00.0: enabling device (0140 -> 0142)

    [ 0.302579] pcieport 0000:00:00.0: Signaling PME with IRQ 53

    [ 0.302785] pcieport 0000:00:00.0: AER enabled with IRQ 53

    [ 0.302979] pci 0000:01:00.0: enabling device (0140 -> 0142)

    [ 0.307391] iproc-rng200 fe104000.rng: hwrng registered

    [ 0.307681] vc-mem: phys_addr:0x00000000 mem_base=0x3ec00000 mem_size:0x40000000(1024 MiB)

    [ 0.308310] vc-sm: Videocore shared memory driver

    [ 0.314796] vc4-drm soc:gpu: bound fe600000.firmwarekms (ops 0xc0c5f388)

    [ 0.315441] [drm] Initialized vc4 0.0.0 20140616 for soc:gpu on minor 0

    [ 0.315457] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).

    [ 0.315469] [drm] No driver support for vblank timestamp query.

    [ 0.315481] [drm] Setting vblank_disable_immediate to false because get_vblank_timestamp == NULL

    [ 0.482273] Console: switching to colour frame buffer device 240x67

    [ 0.515588] vc4-drm soc:gpu: fb0: DRM emulated frame buffer device

    [ 0.528052] brd: module loaded

    [ 0.528199] loop: module loaded

    [ 0.550267] usbcore: registered new interface driver rtsx_usb

    [ 0.551379] Loading iSCSI transport class v2.0-870.

    [ 0.551814] iscsi: registered transport (tcp)

    [ 0.553520] libphy: Fixed MDIO Bus: probed

    [ 0.553559] tun: Universal TUN/TAP device driver, 1.6

    [ 0.554358] bcmgenet fd580000.genet: failed to get enet clock

    [ 0.554378] bcmgenet fd580000.genet: GENET 5.0 EPHY: 0x0000

    [ 0.554401] bcmgenet fd580000.genet: failed to get enet-wol clock

    [ 0.554422] bcmgenet fd580000.genet: failed to get enet-eee clock

    [ 0.554450] bcmgenet: Skipping UMAC reset

    [ 0.554839] unimac-mdio unimac-mdio.-19: DMA mask not set

    [ 0.565249] libphy: bcmgenet MII bus: probed

    [ 0.592880] unimac-mdio unimac-mdio.-19: Broadcom UniMAC MDIO bus at 0x(ptrval)

    [ 0.593850] usbcore: registered new interface driver lan78xx

    [ 0.593900] usbcore: registered new interface driver dm9601

    [ 0.593957] usbcore: registered new interface driver smsc95xx

    [ 0.594273] xhci_hcd 0000:01:00.0: xHCI Host Controller

    [ 0.594307] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 1

    [ 0.596957] xhci_hcd 0000:01:00.0: hcc params 0x002841eb hci version 0x100 quirks 0x0000001000000890

    [ 0.597158] genirq: irq_chip Brcm_MSI did not update eff. affinity mask of irq 54

    [ 0.597905] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19

    [ 0.597924] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1

    [ 0.597940] usb usb1: Product: xHCI Host Controller

    [ 0.597955] usb usb1: Manufacturer: Linux 4.19.83 xhci-hcd

    [ 0.597970] usb usb1: SerialNumber: 0000:01:00.0

    [ 0.598596] hub 1-0:1.0: USB hub found

    [ 0.598662] hub 1-0:1.0: 1 port detected

    [ 0.599157] xhci_hcd 0000:01:00.0: xHCI Host Controller

    [ 0.599184] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2

    [ 0.599208] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed

    [ 0.599661] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 4.19

    [ 0.599677] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1

    [ 0.599692] usb usb2: Product: xHCI Host Controller

    [ 0.599707] usb usb2: Manufacturer: Linux 4.19.83 xhci-hcd

    [ 0.599721] usb usb2: SerialNumber: 0000:01:00.0

    [ 0.600312] hub 2-0:1.0: USB hub found

    [ 0.600387] hub 2-0:1.0: 4 ports detected

    [ 0.601744] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)

    [ 0.602068] dwc_otg: FIQ enabled

    [ 0.602081] dwc_otg: NAK holdoff enabled

    [ 0.602093] dwc_otg: FIQ split-transaction FSM enabled

    [ 0.602109] Module dwc_common_port init

    [ 0.602356] usbcore: registered new interface driver uas

    [ 0.602466] usbcore: registered new interface driver usb-storage

    [ 0.602668] mousedev: PS/2 mouse device common for all mice

    [ 0.603053] i2c /dev entries driver

    [ 0.605710] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer

    [ 0.605980] bcm2835-cpufreq: min=600000 max=1500000

    [ 0.606852] sdhci: Secure Digital Host Controller Interface driver

    [ 0.606865] sdhci: Copyright(c) Pierre Ossman

    [ 0.607395] mmc-bcm2835 fe300000.mmcnr: could not get clk, deferring probe

    [ 0.607946] sdhci-pltfm: SDHCI platform and OF driver helper

    [ 0.611525] ledtrig-cpu: registered to indicate activity on CPUs

    [ 0.611596] hidraw: raw HID events driver (C) Jiri Kosina

    [ 0.612802] usbcore: registered new interface driver usbhid

    [ 0.612807] usbhid: USB HID core driver

    [ 0.613252] vchiq: vchiq_init_state: slot_zero = (ptrval), is_master = 0

    [ 0.614320] [vc_sm_connected_init]: start

    [ 0.620631] [vc_sm_connected_init]: end - returning 0

    [ 0.621345] bcm2835_vc_sm_cma_probe: Videocore shared memory driver

    [ 0.621366] [vc_sm_connected_init]: start

    [ 0.621764] [vc_sm_connected_init]: installed successfully

    [ 0.623763] NET: Registered protocol family 10

    [ 0.625044] Segment Routing with IPv6

    [ 0.625125] NET: Registered protocol family 17

    [ 0.625282] Key type dns_resolver registered

    [ 0.625571] Registering SWP/SWPB emulation handler

    [ 0.626192] Loading compiled-in X.509 certificates

    [ 0.635240] uart-pl011 fe201000.serial: cts_event_workaround enabled

    [ 0.635318] fe201000.serial: ttyAMA0 at MMIO 0xfe201000 (irq = 34, base_baud = 0) is a PL011 rev2

    [ 0.639053] bcm2835-power bcm2835-power: Broadcom BCM2835 power domains driver

    [ 0.639389] brcmstb_thermal fd5d2200.thermal: registered AVS TMON of-sensor driver

    [ 0.639792] mmc-bcm2835 fe300000.mmcnr: mmc_debug:0 mmc_debug2:0

    [ 0.639799] mmc-bcm2835 fe300000.mmcnr: DMA channel allocated

    [ 0.666143] sdhci-iproc fe340000.emmc2: Linked as a consumer to regulator.1

    [ 0.685029] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)

    [ 0.686710] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)

    [ 0.688382] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)

    [ 0.691487] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)

    [ 0.693160] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)

    [ 0.701358] mmc0: SDHCI controller on fe340000.emmc2 [fe340000.emmc2] using ADMA

    [ 0.710327] [drm] Initialized v3d 1.0.0 20180419 for fec00000.v3d on minor 1

    [ 0.711670] console [netcon0] enabled

    [ 0.711675] netconsole: network logging started

    [ 0.711681] of_cfs_init

    [ 0.711702] of_cfs_init: OK

    [ 0.711878] ALSA device list:

    [ 0.711883] No soundcards found.

    [ 0.718773] Freeing unused kernel memory: 6144K

    [ 0.718895] Run /init as init process

    [ 0.734371] random: fast init done

    [ 0.761221] mmc0: new high speed SDHC card at address aaaa

    [ 0.761713] mmc1: new high speed SDIO card at address 0001

    [ 0.763394] mmcblk0: mmc0:aaaa SU16G 14.8 GiB

    [ 0.764996] mmcblk0: p1 p2

    [ 0.796944] Checking disk(s): UUID=2311-4421 UUID=4a7717ae-4e4f-431a-86cf-643c8bb8834a

    [ 0.928547] usb 1-1: new high-speed USB device number 2 using xhci_hcd

    [ 1.069721] usb 1-1: New USB device found, idVendor=2109, idProduct=3431, bcdDevice= 4.20

    [ 1.069729] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0

    [ 1.069735] usb 1-1: Product: USB2.0 Hub

    [ 1.070873] hub 1-1:1.0: USB hub found

    [ 1.071187] hub 1-1:1.0: 4 ports detected

    [ 1.192123] usb 2-2: new SuperSpeed Gen 1 USB device number 2 using xhci_hcd

    [ 1.209633] usb 2-2: New USB device found, idVendor=1058, idProduct=25a2, bcdDevice=10.14

    [ 1.209640] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3

    [ 1.209646] usb 2-2: Product: Elements 25A2

    [ 1.209652] usb 2-2: Manufacturer: Western Digital

    [ 1.209658] usb 2-2: SerialNumber: 575832314136364C37583945

    [ 1.211766] usb-storage 2-2:1.0: USB Mass Storage device detected

    [ 1.212048] scsi host0: usb-storage 2-2:1.0

    [ 1.355208] usb 1-1.3: new low-speed USB device number 3 using xhci_hcd

    [ 1.364161] fsck: CP437: Invalid argument

    [ 1.364161] fsck: fsck.fat 3.0.28 (2015-05-16)

    [ 1.364161] fsck: /dev/mmcblk0p1: 210 files, 18467/65501 clusters

    [ 1.364161] fsck: STORAGE: recovering journal

    [ 1.364161] fsck: STORAGE: clean, 5926/3758080 files, 721297/15029760 blocks

    [ 1.465374] usb 1-1.3: New USB device found, idVendor=1a2c, idProduct=0027, bcdDevice= 1.10

    [ 1.465384] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0

    [ 1.465391] usb 1-1.3: Product: USB Keykoard

    [ 1.465397] usb 1-1.3: Manufacturer: USB

    [ 1.472001] input: USB USB Keykoard as /devices/platform/scb/http://fd500000.pcie/pci0000:00/000…01/input/input0

    [ 1.528919] hid-generic 0003:1A2C:0027.0001: input,hidraw0: USB HID v1.10 Keyboard [USB USB Keykoard] on usb-0000:01:00.0-1.3/input0

    [ 1.533545] input: USB USB Keykoard Consumer Control as /devices/platform/scb/http://fd500000.pcie/pci0000:00/000…02/input/input1

    [ 1.588702] input: USB USB Keykoard System Control as /devices/platform/scb/http://fd500000.pcie/pci0000:00/000…02/input/input2

    [ 1.588850] hid-generic 0003:1A2C:0027.0002: input,hidraw1: USB HID v1.10 Device [USB USB Keykoard] on usb-0000:01:00.0-1.3/input1

    [ 1.677682] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)

    [ 2.105754] systemd[1]: System time before build time, advancing clock.

    [ 2.112355] systemd[1]: systemd 242 running in system mode. (-PAM -AUDIT -SELINUX -IMA -APPARMOR -SMACK +SYSVINIT -UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS -ACL -XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD +IDN2 -IDN -PCRE2 default-hierarchy=hybrid)

    [ 2.112672] systemd[1]: Detected architecture arm.

    [ 2.115884] systemd[1]: Set hostname to <LibreELEC>.

    [ 2.119329] systemd[1]: Failed to bump fs.file-max, ignoring: Invalid argument

    [ 2.226933] random: systemd: uninitialized urandom read (16 bytes read)

    [ 2.230798] systemd[1]: Starting Show Version...

    [ 2.231026] random: systemd: uninitialized urandom read (16 bytes read)

    [ 2.231503] systemd[1]: Listening on udev Control Socket.

    [ 2.231655] random: systemd: uninitialized urandom read (16 bytes read)

    [ 2.232149] systemd[1]: Listening on Journal Socket.

    [ 2.234572] systemd[1]: Mounting Kernel Debug File System...

    [ 2.237084] systemd[1]: Starting Create Persistent Log Directory on /storage...

    [ 2.237485] systemd[1]: Condition check resulted in Huge Pages File System being skipped.

    [ 2.239025] scsi 0:0:0:0: Direct-Access WD Elements 25A2 1014 PQ: 0 ANSI: 6

    [ 2.241309] sd 0:0:0:0: [sda] Spinning up disk...

    [ 2.377281] kernel-overlays-setup: setup base modules

    [ 2.427560] kernel-overlays-setup: added modules from /usr/lib/kernel-overlays/base/lib/modules/4.19.83

    [ 2.459779] kernel-overlays-setup: added firmware from /usr/lib/kernel-overlays/base/lib/firmware

    [ 2.459906] kernel-overlays-setup: adding overlays from /storage/.cache/kernel-overlays

    [ 2.461084] kernel-overlays-setup: done

    [ 2.662615] systemd-journald[213]: Received request to flush runtime journal from PID 1

    [ 3.217385] random: crng init done

    [ 3.217395] random: 7 urandom warning(s) missed due to ratelimiting

    [ 3.251865] .

    [ 3.724306] rpivid-mem feb00000.hevc-decoder: rpivid-hevcmem initialised: Registers at 0xfeb00000 length 0x0000ffff

    [ 3.724625] rpivid-mem feb10000.rpivid-local-intc: rpivid-intcmem initialised: Registers at 0xfeb10000 length 0x00000fff

    [ 3.724871] rpivid-mem feb20000.h264-decoder: rpivid-h264mem initialised: Registers at 0xfeb20000 length 0x0000ffff

    [ 3.725101] rpivid-mem feb30000.vp9-decoder: rpivid-vp9mem initialised: Registers at 0xfeb30000 length 0x0000ffff

    [ 3.728691] gpiomem-bcm2835 fe200000.gpiomem: Initialised: Registers at 0xfe200000

    [ 3.729296] media: Linux media interface: v0.10

    [ 3.912146] videodev: Linux video capture interface: v2.00

    [ 4.108050] cfg80211: Loading compiled-in X.509 certificates for regulatory database

    [ 4.114884] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'

    [ 4.237789] brcmfmac: F1 signature read @0x18000000=0x15264345

    [ 4.256162] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6

    [ 4.256452] usbcore: registered new interface driver brcmfmac

    [ 4.265748] .

    [ 4.349408] bcm2835_mmal_vchiq: module is from the staging directory, the quality is unknown, you have been warned.

    [ 4.356813] bcm2835_codec: module is from the staging directory, the quality is unknown, you have been warned.

    [ 4.360280] bcm2835-codec bcm2835-codec: Device registered as /dev/video10

    [ 4.360301] bcm2835-codec bcm2835-codec: Loaded V4L2 decode

    [ 4.362268] bcm2835-codec bcm2835-codec: Device registered as /dev/video11

    [ 4.362284] bcm2835-codec bcm2835-codec: Loaded V4L2 encode

    [ 4.364332] bcm2835-codec bcm2835-codec: Device registered as /dev/video12

    [ 4.364347] bcm2835-codec bcm2835-codec: Loaded V4L2 isp

    [ 4.669610] bcmgenet: Skipping UMAC reset

    [ 4.738895] bcmgenet fd580000.genet: configuring instance for external RGMII (no delay)

    [ 4.739234] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready

    [ 4.780613] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6

    [ 4.794008] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Feb 27 2018 03:15:32 version 7.45.154 (r684107 CY) FWID 01-4fbe0b04

    [ 4.855601] uart-pl011 fe201000.serial: no DMA platform data

    [ 4.900163] input: lircd-uinput as /devices/virtual/input/input3

    [ 4.945461] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready

    [ 4.945477] brcmfmac: power management disabled

    [ 5.049723] input: eventlircd as /devices/virtual/input/input4

    [ 5.278529] .

    [ 5.758656] bcmgenet fd580000.genet eth0: Link is Down

    [ 6.295189] ..ready

    [ 7.305530] sd 0:0:0:0: [sda] 1953458176 512-byte logical blocks: (1.00 TB/931 GiB)

    [ 7.306042] sd 0:0:0:0: [sda] Write Protect is off

    [ 7.306049] sd 0:0:0:0: [sda] Mode Sense: 47 00 10 08

    [ 7.306565] sd 0:0:0:0: [sda] No Caching mode page found

    [ 7.306572] sd 0:0:0:0: [sda] Assuming drive cache: write through

    [ 7.355240] sda: sda1

    [ 7.360701] sd 0:0:0:0: [sda] Attached SCSI disk

    [ 7.768739] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready

    [ 7.843927] fuse init (API version 7.27)

    [ 9.012198] Under-voltage detected! (0x00050005)

    [ 11.474438] Bluetooth: Core ver 2.22

    [ 11.474513] NET: Registered protocol family 31

    [ 11.474519] Bluetooth: HCI device and connection manager initialized

    [ 11.474533] Bluetooth: HCI socket layer initialized

    [ 11.474542] Bluetooth: L2CAP socket layer initialized

    [ 11.474567] Bluetooth: SCO socket layer initialized

    [ 11.480613] Bluetooth: HCI UART driver ver 2.3

    [ 11.480622] Bluetooth: HCI UART protocol H4 registered

    [ 11.480684] Bluetooth: HCI UART protocol Three-wire (H5) registered

    [ 11.480837] Bluetooth: HCI UART protocol Broadcom registered

    [ 15.411914] Voltage normalised (0x00000000)

    [ 17.545326] Under-voltage detected! (0x00050005)

    [ 20.855358] vchiq: 0: ignoring ERROR from callback to service 9008

    [ 23.945231] Voltage normalised (0x00000000)

    HDDREC2020:~ # ps | grep /usr/sbin/lircd

    481 root 0:00 /usr/sbin/lircd --nodaemon /storage/.config/lircd.conf

    482 root 0:00 /usr/sbin/lircd-uinput --add-release-events

    956 root 0:00 grep /usr/sbin/lircd

    HDDREC2020:~ # ir-keytable -r

    /sys/class/rc/: No such file or directory

    No devices found

    HDDREC2020:~ # ir-keytable -t

    /sys/class/rc/: No such file or directory

    No devices found

    HDDREC2020:~ #

  • dtoverlay=gpio-ir brought partial success

    LibreELEC (official): 9.2.0 (RPi4.arm)

    HDDREC2020:~ # ir-keytable

    Found /sys/class/rc/rc0/ (/dev/input/event3) with:

    Name: gpio_ir_recv

    Driver: gpio_ir_recv, table: rc-rc6-mce

    lirc device: /dev/lirc0

    Supported protocols: lirc rc-5 rc-5-sz jvc sony nec sanyo mce_kbd rc-6 sharp xmp imon rc-mm

    Enabled protocols: lirc

    bus: 25, vendor/product: 0001:0001, version: 0x0100

    Repeat delay = 500 ms, repeat period = 125 ms

    maybe i need to activate the correct keymap for my remote ?!

  • You seem to have put a lircd.conf file into /storage/.config so lirc is used - make sure the file matches the remote you are using.

    You can also try running ir-keytable -p all -t, if that outputs lirc scancodes when you press buttons it means the IR protocol is supported by the kernel (the output will show you which protocol that is) and you can drop the lircd.conf file and use ir-keytable / rc_maps.cfg configuration instead (which is a lot less error-prone than using irrecord to create a lircd.conf file).

    so long,

    Hias