Common DVB-T DVB-S dvb-c topic

    That's right, drivers for dvb-s2 / dvb-t2 are errors. the problem is with the dvb-s2 on the Polish channels with hotbird 13E
    It can help a programmer? I have a source drivers.


    Sorry for my English

    Edited once, last by segment (October 11, 2016 at 9:07 PM).


    May be is the region? Another user have the same my problem with kIplus here in Italy.
    About 24p output, Kodi is set correctly. Now I updated to another build and 24p work ok without any change (updated don't lose settings).
    I noticed that when movie start, the system TRY to change frequency, but after a while it return to 60p. I have a Videoprojector and not a TV set.
    With tuner, if I start one of channel working, the frequency CHANGE at 50p. It's only the 24 P that don't work.
    I don't understand too...

    Quote from willyfan


    May be is the region? Another user have the same my problem with kIplus here in Italy.
    About 24p output, Kodi is set correctly. Now I updated to another build and 24p work ok without any change (updated don't lose settings).
    I noticed that when movie start, the system TRY to change frequency, but after a while it return to 60p. I have a Videoprojector and not a TV set.
    With tuner, if I start one of channel working, the frequency CHANGE at 50p. It's only the 24 P that don't work.
    I don't understand too...

    What gui refresh rate use you?
    For me, when gui is 50hz, then have I problem's.
    At 60 Hz gui no problems.
    Maybe over android you have power output to amplifier, and with tvheadend/Libreelec you not turning on this option.
    And not forget, the 24P 2 mode exists: 23.976, and 24. Your Beamer support both?

    I use 60p normally. I have a roof antenna with his amplifier. It don't need power from receiver, anyway from Android I don't have power out.
    My projector support 24 and 23.976, anyway with others build it work, so, why you ask me this?


    William Fanelli

    For those with tuning problem, try using VDR instead tvheadend, I also had problems with tvheadend, finding muxes, channels in dvb-t, switching diseqc in dvb-s...etc, under VDR everything works just fine, I have one mixed list in pvr now, all channels from dvbt and dvbs, and I can switch between them without any problem.

    KI plus Libreelec 7.0.2.004

    Edited once, last by njofr@ (October 12, 2016 at 7:07 AM).

    Quote from njofr@


    For those with tuning problem, try using VDR instead tvheadend, I also had problems with tvheadend, finding muxes, channels in dvb-t, switching diseqc in dvb-s...etc, under VDR everything works just fine, I have one mixed list in pvr now, all channels from dvbt and dvbs, and I can switch between them without any problem.

    KI plus Libreelec 7.0.2.004

    I will try with VDR...
    [hr]
    Ok, I installed VDR. It work, scan is ok, all channel is ok.
    But I have a couple of issue:
    1) EPG don't work, I have no info.
    2) Channel order is not correct.

    With tvhedend this thing was working, so....

    Someone can help me?

    Edited once, last by willyfan (October 12, 2016 at 11:18 AM).

    Hello,

    I have installed LibreElec 004.2 on my K1 plus. Everything works fine, but i have minor glitches when watching DVB-S2 channels using OSCAM. I Use VDR and OSCam from the image. It seems like every x seconds some frames get dropped.
    Any idea how i can fix this ?

    Thanks,

    Francesco

    Now the EPG is working (I don't know what I done but work...).
    The last problem is order of channel. The order isn't not the LCN, and I can't assign a number manually t a channel.
    Somone know how modify the order?