Does this work for Libreelec/CoreELEC 9.0?
To answer your question, from the first post edit: new version of OpenPHT 1.9 is based od LibreELEC 8.2 by kszaq and it can be updated form LibreELEC 8.2
Posts by bubblegum57
-
-
install reboot and then install to internal again
then read the links regarding the remote (oops) wrong post
search for the instructions regarding installing remote
-
If I were you, I would forget about Leia for the moment, they are currently alpha
Once you get a working device, & a bit more experienced, then try Leia.
So, if you go here, [INDEX] LibreELEC community builds for Amlogic
Choose a Krypton build from [8.2.3.1] LibreELEC 8.2 for S905/S905X I know it says discontinued
Read the how to [HOWTO + FAQ] Install community builds on S905/S905D/S905W/S905X/S912 device
then download the imgz file & the device tree which is based on the RAM size & LAN speed
Burn image to microsd or usb using etcher or rufus copy the device tree to the root, rename it to dtb.img
Insert into device reboot holding reset button on device, after a few seconds it should reboot to libreelec, you will probably find the remote doesn't work, so use a keyboard
Set ssh to on,
to get the remote working, go to the thread remote.conf repository
if there isn't a remote there create your own from Create remote.conf from scratch
-
Display More
when sd card is inside it works , when I remove SD card it throw error about super-block etc..
how can I use dtb.img to internal ?
another problem is with remote . it does not work even I copy remote.conf to /storage/.config and restart .
with SD card it does not see internal partition . Why ?
LibreELEC:~ # df -h
Filesystem Size Used Available Use% Mounted on
devtmpfs 785.8M 125.5M 660.3M 16% /dev
/dev/mmcblk1p1 511.7M 229.5M 282.3M 45% /flash
/dev/mmcblk1p2 27.4G 4.3M 27.4G 0% /storage
/dev/loop0 125.6M 125.6M 0 100% /
tmpfs 895.2M 0 895.2M 0% /dev/shm
tmpfs 895.2M 7.0M 888.2M 1% /run
tmpfs 895.2M 0 895.2M 0% /sys/fs/cgroup
tmpfs 895.2M 1.9M 893.3M 0% /var
tmpfs 895.2M 4.0K 895.2M 0% /tmp
regards,
On some devices you have to run installtointernal twice.
If it doesn't work, perhaps the nand is kaput.
But then as you will have read, it is not recommended to install to internal.
you might need to restore the original android to the nand
-
Hey all - I have the latest version working well from SD card - but I would like to flash this permanently on my GT1 2Gb.
Is there a flashable ZIP file available as I cannot find one?
Any help is appreciated... and TY kszaq !!
It used to be that you ssh in, then type installtointernal on some devices you have to do it twice.
-
There were changes to smb, I think you need to use a password, & possibly set the smb to smb 1 or something.
You need to search, either by google or this forum. I know it's vague, but I use nfs.
-
In recent weeks I have noticed that the general behaviour, & rudeness is increasing. It makes me sad.
Questions are being asked, by people, when they have obviously not searched for the answer. Or, the questions being asked are in the wrong part of the forum.Unfortunately, people have been responding, to this, by being unhelpful & in some cases rudely.
This forum has grown very quickly, & sometimes, it is not easy to find the answer to a question.
So, bear in mind, the devs are working freely in their own time.
Some of the builds, are alpha, so will not work properly.
But, if you think the question is stupid, then just don't respond, rather than being rude.
-
Display More
Hi,I followed instruction like below:
- Firstly we need to stop Kodi and Lirc so SSH to your device and type the following commands
- systemctl stop kodi
- systemctl stop eventlircd
- Next we need to scan for the IR codes
- ir-keytable -t
but system reported error like below:
CoreELEC:~ # ir-keytable -t
No devices found
Could someone help to indicate what wrong with here?
Thanks!
I tried to search about the error, but can not found same issue on google.
I checked system log found there have log like:
[ 280.062140@0] remote: Wrong custom code is 0x4bb41608
[ 280.692492@0] remote: Wrong custom code is 0x4cb31608
[ 281.383970@0] remote: Wrong custom code is 0x48b71608
[ 281.854115@0] remote: Wrong custom code is 0x4ab51608
what box do you have? I found one on here & just copied it to the correct location, & rebooted
-
Thanks, I found it.
About power button menu any suggestions?
sorry no
-
Libreelec configuration is an addon
addons, my addons, all libreelec configuration
-
why don't you try it?
go to settings, interface, skin, get more or something like that
-
Display More
Getting this with that setup..., any idea
Resolving xx.xx.x.xx...
xx.x.x.xx connecting...
SSH-2.0-OpenSSH_7.7
dh-group1-sha1 not specified
crypto error, disconnecting...
SFTP connection error
sorry, no. I assume ssh has been enabled?
-
In coreftp lite
Create a session
put ip address in
user root
password coreelec this is for builds after 8.9 libreelec for 8.2.
port 22
connection SSH/SFTP
-
The remote conf, is only for 8.2. XX builds,
from 8.9 the remote is configured in a totally diifferent way LE9.0 remote configs ir-keytable Amlogic devices
To browse the device, I use coreftp lite,
path for remote.conf is IP address\storage\config (folder)
-
II will do a try
Thank you
Did you copy the remote file
to storage\config renaming your remote file to remote.conf
then reboot
-
-
-
look in the remote thread remote.conf repository
You still haven't told us the name of the device.
