Posts by livs

Solved by removing pcie card.

Thanks.

Just to add additional information: I have 2 video cards in device, both AMD (included in the processor and HD6450).

By bios it is setup to start with onboard card, which is connected to AV by hdmi.

It is possible that this is the problem, that kodi to use a wrong video card and for that reason the message "no display found"?

I will remove later and re-test.

I try to rescue an htpc with amd am1 5350 and I have same message:

ERROR: X11 Error: No Display found

FATAL: CApplication::Create: Unable to init windowing system

Fresh new install with 8.2.2.

kodi log crash attached.

Earlier I manage to start an old image, I can not say what version was on hdd, just it use kodi 17.0. After update to last Milhouse (#210) it not start, just screen with Libreelec.

How to solve this?

Thank you, I will try that.

LE:

Blacklisting RTL8192DE does now show other driver/device: DMf

Update to #0102x with blacklist, no other driver, no wifi connection in settings: DMj

Same #0102x, but remove blacklist, no wifi connection: DMk

I just find an old htpc by Acer which has wifi issue.

As far as I know it includes a wifi card by pci. Strange is that on the case it is mention ralink rt3090, but when I install Libreelec it finds rtl8192DE card.

I do not know the history of the device, however with this driver I have no wifi. I have wired connection but no wifi. With another usb wifi it works, but not with internal.

Can I do something about?

dmesg :

DLE

Thank you.

There are 2 possible issues for you:

1. Driver hd44780 does not work for SSD1306. It is a different controller with different initialization command.

You have to find a hd44780.so file compiled for your oled.

See here as example (not using lcdproc, but still works) Adafruit customer service forums • View topic - 128x32 i2c OLED shows garbage on Odroid-C2, okay on RPi

2. (Small chance) your driver path still is not good.

From your command above it seams another instance of LCDd is running (address already in use).

If you install lcdproc as addon, the correct path is DriverPath=/storage/.kodi/addons/http://service.lcdd/lib/lcdproc/. And LCDd.conf is on \\ip_adress\Userdata\addon_data\service.lcdd

Do you use Rpi? Or what?

Did you make the change without reboot?

If so do a reboot.

You need an oscam compiled for S905 (aarch64) otherwise will not work.

LE: Replace oscam bin with the one attached.
Report if works.

Menthe
The response with imonlcd was for LPB.
Unfortunatelly I emty my box with ideas to solve your problem.

To move forward i suggest to use i2c to connect LCD:
I2C Modul IIC SPI TWI Serielle Schnittstelle PCF8574AT Arduino LCD Raspberry

Quote from Menthe

Ok, checked the drivers you attached. Still not working...

What should i do with the HD44780-rpi.c and HD44780-rpi.h?

Maybe something still wrong with my LCDd.conf?

Do you have a working LibreElec Image with the LCD working i can download?

I try to find old configuration & driver that i use sometime ago, I only find a driver. It may not work.
I modify your LCDd.conf a little, pin definition and drive path to original, as was installed by lcdproc.
Check once again the connections, wires and pin definition.
[hr]

Quote from LPB

Running 7.95.1
Installed LCDproc addon from KODI repository
Tried all setting I could find within addon to get display working. nothing
Tried to SSH in and locate LCD.conf file to edit drivers couldnt locate?? I thought it should be in /etc

Read on a KODI forum that the addon is only a client for LCDd?

Do i need to install this??

How do I install this??

lsusb output is
Bus 001 Device 004: ID 15c2:0038 SoundGraph Inc. GD01 MX LCD Display/IR Receiver

Thanks in Advance

LPB

Display More

The driver that you shall use is imonlcd.
So if you already install lcdproc make the settings to use this driver. To do that go to addon/services/lcdproc and find the driver section.
You have to install XBMC LCDproc addon and enter setting to use lcdproc.

Quote from Menthe

Do i need to use remote LCDproc-Server? (127.0.0.1:13666)

Do that!

Please check drivers from page I posted above, attached.

Do you have in LCDd.conf this type of connection?
"ConnectionType=raspberrypi"

It may be a problem with driver, not compiled for Rpi GPIO.
Can you check if attached version works?
Put the file in storage and change the line in LCDd.conf - example "DriverPath=/storage/.config/raspdrivers/".

Please report back.
And see also here: Raspberry Pi • View topic - RPi 2 with HD44780 (Solved)

LE: It may need to recompile lcdproc for RPI3

Quote from livs

It seam it îs a bug in msi bios vs kernel. I do not go forward as my MB îs dead.

Sent from my iPad using Tapatalk

There is a solution for msi and AMD which I find it sometime ago here: 3.95.5 AMD richland A8 not booting · Issue #3093 · OpenELEC/OpenELEC.tv · GitHub.
I think it was discussed somewhere else here, but i did not bookmark that page.
I manage to revive my MB (an bios update fails) and clean install LE 7.5.1.

How to do:

- Make a flash USB with last LE image.
- Edit syslinux.cfg to add radeon.dpm=0 at live line and installer line
- Boot using flash and install LE
- Boot again using flash and use live
- As in this moment the hdd is mounted, edit the similar cfg file on the hdd to add same (radeon.dpm=0).
- Remove the flash and reboot.

Any version update will work.

Sorry if this was detailed in other post.

LE: The solution was posted by #Milhouse here: thread-1814.html?highlight=boot loop
-

I try to revive an htpc with AMD athlon 5350 and I proceed to install last beta 7.95.1.
But at reboot I have only the logo, did not go to kodi.
Try to access by ssh, not possible, probably ssh is not activated as I remember is one point to do in initial configuration. Same with windows, not find on network (which is wired).
Tried also live session, same situation.
There is a way to solve this issue?
I cannot provide logs.

Solved

I did manage to boot using another AMD GPU and observe errors related to kodi.bin.
Updated with latest Milhouse #1129 using winscp and now works as it should.

However, the question remains why live session on usb did not work.

Tested version 11314 of oscam with emu for x86-64 - see attached.
To install i use an old service oscam zip file (find it with google) where i replace oscam bin with 11314 release - see attached.

To make working:
- uninstall previous oscam
- install from zip and disable autoupdate in config
- add newcamd section in oscam.server - by edit the oscam file or web (ip:8888)
- add user in oscam.user
- add softcam.key in config location of files
- in TVH in section CA add information for newcamd
- restart and should work

I use this on CVH's image from here: Index of /Test/

Update from 7.1.1 december release by wrxtasy.

LE: Solved by extracting boot.ini from image and replace on /flash.
It seams the update did not work as the boot.ini on card after updating was different than the one on the image.

Quote from CvH

We have now, first time ever, a working version for AML (at least it looks like).
These are LibreELEC 7.90.010 builds + Kernel 4.9 DVB Drivers + TBS drivers + T230/C.

Images for:
Odroid_C2
WeTek Core
WeTek Hub
imx6

arm

feel free to report problems

WeTek Play 1/2 are currently evaluated if "we" can fix the included tuner.

Display More

Updating C2 and I have just blue screen after initial splash.
Similar like this: LibreELEC
I use an older boot.ini and now no boot. Can I do something?

Last generic fixed version works for me, even the tuner is seen as Silicon Labs Si2168 instead of TBS saa716x.