Hi, try the following command:
cp /etc/lirc/lircd.conf.rpi .config/lircd.conf
The file lircd.conf is not present under default conditions in .config directory. So you'll copy the MCE Remote Mapping with this command and override the default lirc.conf in /etc/lirc (probably default uses original Odroid Remote mapping). Then reboot the system.
If it does not help, then simply delete the created lircd.conf in .config directory (ssh) respectively Configfiles directory (SMB) and you'll be back where you started. And post here for further assistance 
Hello,
I have the current release installed on Odroid C2 (LibreELEC-Odroid_C2.aarch64-7.90.010).
Everything works fine but the remote is not working.
I want to use the remote of my bluray player (Pioneer) with the Odroid C2 and LibreELEC with the build in IR receiver.
If I run irw there is nothing recognized.
Many thanks in advance for your help.
Best regards
Hartmut
Display More
Hello,I have the current release installed on Odroid C2 (LibreELEC-Odroid_C2.aarch64-7.90.010).
Everything works fine but the remote is not working.I want to use the remote of my bluray player (Pioneer) with the Odroid C2 and LibreELEC with the build in IR receiver.
If I run irw there is nothing recognized.
Many thanks in advance for your help.
Best regards
Hartmut
You would have to follow this guide to use other remotes than Windows Media Center remote or the official Odroid remote. Following the guide, LibreELEC (Lirc) will learn to use all the buttons of your Pioneer remote. You can then backup the created "/storage/.config/lircd.conf", so that you can reuse it whenever you make a reinstall of LibreELEC or so, thus avoiding to do all the steps again and again.
Hello,
thank you for the information.
I have some problems generating my own lirc.conf with irrecord.
For nearly all the buttons of the remote irrecord recognizes the same code.
Thats very strange.
Best regards
Hartmut
Hello,thank you for the information.
I have some problems generating my own lirc.conf with irrecord.
For nearly all the buttons of the remote irrecord recognizes the same code.
Thats very strange.Best regards
Hartmut
hmmm strange.... :/... could you name the exact model of the pioneer bluray player? So I could program my Harmony Remote to imitate your pioneer remote and try it myself. Untunately I cannot promise to do it this weekend, I rather think that I could test it during next week.
Have you tried it with another remote instead of the pioneers one?
hmmm strange.... :/... could you name the exact model of the pioneer bluray player? So I could program my Harmony Remote to imitate your pioneer remote and try it myself. Untunately I cannot promise to do it this weekend, I rather think that I could test it during next week.Have you tried it with another remote instead of the pioneers one?
Hello,
the bluray player is a Pioneer BDP-180
The remote is labeled "RC-2435".
No until now I have not tried another remote. But I should do so.
Many thanks in advance!
Best regards
Hartmut
hi @hru,
I've now programmed my Harmony 950 to use your Pioneer BDP-180 profile and unfortunately I can confirm your issue.
Apparently only the cursors and cannel buttons result in discrete lirc codes:
QuoteKEY_UP 0x21DE
KEY_DOWN 0xA15E
KEY_RIGHT 0x619E
KEY_LEFT 0xE11E
KEY_CHANNELUP 0x21DE
KEY_CHANNELDOWN 0xA15E
all the other buttons are recognized as 0x817E ir code. Thats really strange, never saw this behaviour on one of my remotes hm :/... I'm afraid you will have to use another remote hmm...
But anyways, why not use HDMI CEC, i.e. use your TV's remote to control the C2?
My test lircd.conf with your remote profile:
# Please take the time to finish this file as described in
# https://sourceforge.net/p/lirc-remotes/wiki/Checklist/
# and make it available to others by sending it to
# <lirc@bartelmus.de>
#
# This config file was automatically generated
# using lirc-0.9.4(default) on Tue Jan 3 23:18:28 2017
# Command line used: --device /dev/lirc0 /storage/.config/lircd.conf
# Kernel version (uname -r): 3.14.29
#
# Remote name (as of config file): Pioneer_BDP-180
# Brand of remote device, the thing you hold in your hand:
# Remote device model nr:
# Remote device info url:
# Does remote device has a bundled capture device e. g., a
# usb dongle? :
# For bundled USB devices: usb vendor id, product id
# and device string (use dmesg or lsusb):
# Type of device controlled
# (TV, VCR, Audio, DVD, Satellite, Cable, HTPC, ...) :
# Device(s) controlled by this remote:
begin remote
name Pioneer_BDP-180
bits 16
flags SPACE_ENC
eps 30
aeps 100
header 8421 4282
one 490 1633
zero 490 562
ptrail 487
pre_data_bits 16
pre_data 0x857A
gap 25307
toggle_bit_mask 0x0
frequency 38000
begin codes
KEY_EPG 0x817E
KEY_OK 0x817E
KEY_UP 0x21DE
KEY_DOWN 0xA15E
KEY_RIGHT 0x619E
KEY_LEFT 0xE11E
KEY_VCR 0x817E
KEY_RED 0x817E
KEY_GREEN 0x817E
KEY_YELLOW 0x817E
KEY_BLUE 0x817E
KEY_CHANNELUP 0x21DE
KEY_CHANNELDOWN 0xA15E
KEY_INFO 0x817E
KEY_EXIT 0x817E
KEY_HOME 0x817E
KEY_STOP 0x817E
KEY_PLAY 0x817E
KEY_PAUSE 0x817E
KEY_NEXT 0x817E
KEY_PREVIOUS 0x817E
KEY_FASTFORWARD 0x817E
KEY_REWIND 0x817E
KEY_POWER 0x817E
end codes
end remoteDisplay More
hi @hru,I've now programmed my Harmony 950 to use your Pioneer BDP-180 profile and unfortunately I can confirm your issue.
Apparently only the cursors and cannel buttons result in discrete lirc codes:
all the other buttons are recognized as 0x817E ir code. Thats really strange, never saw this behaviour on one of my remotes hm :/... I'm afraid you will have to use another remote hmm...
But anyways, why not use HDMI CEC, i.e. use your TV's remote to control the C2?
My test lircd.conf with your remote profile:
CodeDisplay More# Please take the time to finish this file as described in # https://sourceforge.net/p/lirc-remotes/wiki/Checklist/ # and make it available to others by sending it to # <lirc@bartelmus.de> # # This config file was automatically generated # using lirc-0.9.4(default) on Tue Jan 3 23:18:28 2017 # Command line used: --device /dev/lirc0 /storage/.config/lircd.conf # Kernel version (uname -r): 3.14.29 # # Remote name (as of config file): Pioneer_BDP-180 # Brand of remote device, the thing you hold in your hand: # Remote device model nr: # Remote device info url: # Does remote device has a bundled capture device e. g., a # usb dongle? : # For bundled USB devices: usb vendor id, product id # and device string (use dmesg or lsusb): # Type of device controlled # (TV, VCR, Audio, DVD, Satellite, Cable, HTPC, ...) : # Device(s) controlled by this remote: begin remote name Pioneer_BDP-180 bits 16 flags SPACE_ENC eps 30 aeps 100 header 8421 4282 one 490 1633 zero 490 562 ptrail 487 pre_data_bits 16 pre_data 0x857A gap 25307 toggle_bit_mask 0x0 frequency 38000 begin codes KEY_EPG 0x817E KEY_OK 0x817E KEY_UP 0x21DE KEY_DOWN 0xA15E KEY_RIGHT 0x619E KEY_LEFT 0xE11E KEY_VCR 0x817E KEY_RED 0x817E KEY_GREEN 0x817E KEY_YELLOW 0x817E KEY_BLUE 0x817E KEY_CHANNELUP 0x21DE KEY_CHANNELDOWN 0xA15E KEY_INFO 0x817E KEY_EXIT 0x817E KEY_HOME 0x817E KEY_STOP 0x817E KEY_PLAY 0x817E KEY_PAUSE 0x817E KEY_NEXT 0x817E KEY_PREVIOUS 0x817E KEY_FASTFORWARD 0x817E KEY_REWIND 0x817E KEY_POWER 0x817E end codes end remote
Hello,
thank you very much for your assistance.
I will now try to use another remote.
I do not use CEC because the TV is too old for CEC;-)
Best regards
Hartmut
Hello,
sorry but I need your assistance once again.
I want to use the remote Hauppauge PVR 350.
I have a lircd.conf file for this remote and copy it to /storage/.config and rebooted the Odroid C2 with LibreELEC.
But it does not work.
irw does not generate any output.
mode2 -d /dev/lirc0 does generate an output when pressing any key on the remote.
ir-keytable generates the following output:
Found /sys/class/rc/rc0/ (/dev/input/event6) with:
Driver meson-ir, table rc-empty
Supported protocols: lirc rc-5 jvc sony nec sanyo mce-kbd rc-6
Enabled protocols: lirc
Name: meson-ir
bus: 25, vendor/product: 0000:0000, version: 0x0000
Repeat delay = 1000 ms, repeat period = 125 mslsmod generates the following output:
Module Size Used by
fuse 80251 3
8021q 19087 0
rtc_pcf8563 3551 0
ir_lirc_codec 4412 0
lirc_dev 8568 1 ir_lirc_codec
ir_mce_kbd_decoder 3076 0
ir_sanyo_decoder 1563 0
ir_sony_decoder 1601 0
ir_jvc_decoder 1591 0
ir_rc6_decoder 1959 0
ir_nec_decoder 1719 0
ir_rc5_decoder 1527 0
meson_ir 3793 0
mali 199832 5
autofs4 24843 0
fbcon 37535 0
bitblit 4444 1 fbcon
softcursor 1200 1 bitblit
font 7279 1 fbconAny ideas what goes wrong?
Many thanks in advance for any help.
Best regards
Hartmut
I'm not sure why you don't simply follow the guide for making your own lircd.conf...
I've tried it with my harmony... Your given profile does not work for me either. But following the above linked guide, I made a custom lircd.conf (see attachment: lircd_harmony-hauppauge-pvr350.zip)
The thing is that some buttons give the same codes:
This is likely because I used a harmony to simulate yours. Perhaps you don't even have some of the mentioned buttons on the Hauppauge remote. But as I said: Simply follow the guide to create your own lircd.conf and it will work this time with the hauppage remote. Seems to be a pretty appropriate one for LibreELEC
I'm not sure why you don't simply follow the guide for making your own lircd.conf...I've tried it with my harmony... Your given profile does not work for me either. But following the above linked guide, I made a custom lircd.conf (see attachment: )
The thing is that some buttons give the same codes:
- INFO and MENU button have the same code 0x17CD
- and the buttons SUBTITLE/CLOSED CAPTION/ # have the same code 0x17CE
This is likely because I used a harmony to simulate yours. Perhaps you don't even have some of the mentioned buttons on the Hauppauge remote. But as I said: Simply follow the guide to create your own lircd.conf and it will work this time with the hauppage remote. Seems to be a pretty appropriate one for LibreELEC
Hello,
many thanks for the lircd.conf.
I have tried it. But it does not work. irw also does not generate any output.
I think the reason is not the lircd.conf but something else.
If I try to generate my own lircd.conf file with irrecord I get the following error message:
Now hold down button "KEY_OK".
Something went wrong: Cannot decode data
Too many errors.
Check TROUBLESHOOTING in irrecord(1) manpage.
Or try using the -f option.
Unrecoverable error: Cannot decode data
Giving up
Check TROUBLESHOOTING in irrecord manpage.
And there is no file created.
The command "mode2 -d /dev/lirc0"generates an output if pressing a key on the remote. See the attached file.
Have you an idea what is going wrong?
Many thanks in advance for your help.
Best regards
Hartmut
Hmmm... unfortunately I don't have a clue what's wrong there :/. Perhaps the IR Receiver of your odroid is defective? May be try again another remote or another LibreELEC build (wrxtasy ODROID Forum • View topic - LibreELEC 7.1.3 - Kodi Jarvis - February update) and if that doesn't help either, then best would be to open a thread at forum.odroid.com with your issue... perhaps somebody can you give some advice there -_-.
Hmmm... unfortunately I don't have a clue what's wrong there :/. Perhaps the IR Receiver of your odroid is defective? May be try again another remote or another LibreELEC build (wrxtasy ODROID Forum • View topic - LibreELEC 7.1.3 - Kodi Jarvis - February update) and if that doesn't help either, then best would be to open a thread at forum.odroid.com with your issue... perhaps somebody can you give some advice there -_-.
Hello Infinity85,
thank you for your answer.
How can I verify if the IR Receiver of the Odroid C2 is defective?
Best regards
Hartmut
Hello Infinity85,thank you for your answer.
How can I verify if the IR Receiver of the Odroid C2 is defective?Best regards
Hartmut
I don't know either, unfortunately. But that could certainly be answered at forum.odroid.com in hardware and peripheral or in issues section.
