I have upgraded from RPi3 to RPi4 and can only get 1024x768 on same display (12 year old Dell WFP3008) supporting 1920x1080 (on RPi3 1920x1080 was working well). Is there any way to force resolution?
PS Reasons for upgrading from RPi3 was that after playing several videos I am starting to have following problems:
1. Seeking video position doesn't work until 10-15 seconds of video played.
2. When video ends RPi3 freezed for 30-60 seconds (even network control doesn't work).
Maybe you can help with this ones.
RPi4 force resolution
-
bazuchan -
August 12, 2020 at 8:16 AM -
Thread is Unresolved
-
- Official Post
-
Sorry to necro this thread, but it is the top result on google for "libreelec force resolution" so I'm going to say that this is valuable real estate, and exactly the right place to put the correct answer. You're not wrong, but a bit terse.
https://wiki.libreelec.tv/config.txt 404's now, so your 'helpful' reply, which is the top result on Google for "libreelec force resolution" isn't very helpful, less than a year later.
https://wiki.libreelec.tv/configuration/config_txt is the link now.
URL's aren't supposed to break, ever. Don't contribute to link rot!
Here's a more helpful reply:
Hey, I was running into the same problem!
I solved it by adding two (2!) lines to my config.txt:
Codehdmi_group=1 hdmi_mode=16Here's the full config.txt that solved my issue:
Code
Display More# SPDX-License-Identifier: GPL-2.0-or-later # Copyright (C) 2009-2014 Stephan Raue ([email protected]) # Copyright (C) 2016-present Team LibreELEC (https://libreelec.tv) ################################################################################ # Bootloader configuration - config.txt ################################################################################ ################################################################################ # Memory (System/GPU configuration ) ################################################################################ # Default GPU memory split - at least 288M is needed for some 4k HEVC files gpu_mem=320 ################################################################################ # For overclocking and various other settings, see: # https://www.raspberrypi.org/documentation/configuration/config-txt.md ################################################################################ # Set 'force_turbo=1' to disable dynamic overclocking and enable overclocking always. force_turbo=0 # Force HDMI even if unplugged or powered off # hdmi_force_hotplug=1 # Doesn't sent initial active source message. # Avoids bringing CEC (enabled TV) out of standby and channel switch when # rebooting. hdmi_ignore_cec_init=1 ################################################################################ # End of default configuration ################################################################################ ################################################################################ # Display configuration to set display to 1080P@60hz ################################################################################ # See https://www.raspberrypi.org/documentation/configuration/config-txt/video.md # Your display may differ! Refer to the above link! # Set HDMI to to 1080P for a TELEVISION, per https://www.raspberrypi.org/documentation/configuration/config-txt/video.md # There are two options, this assumes you're on a TV. If you're on a monitor, # Comment the next two lines block, and uncomment the next two lines, instead hdmi_group=1 hdmi_mode=16 # If you're on a monitor, and the above block doesn't work, comment it out # and uncomment these lines. #hdmi_group=2 # hdmi_mode=82 ################################################################################ # Include distribution specific config file if it exists. ################################################################################ [all] include distroconfig.txtFlex, on urbandictionary:
QuoteAdjective: To stunt or show off used by many rappers in various songs.
I ain't gotta flex, boy I got it, ooh, ooh, ooh, ooh - Rich Homie Quan
by TrapKingzofIslip July 16, 2015
-
- Official Post
victorbiederbeck Thanks for pointing me to the dead link. I updated it. We went to a new Wiki, which broke something.
PS: Also urban slang: flex = turntable
PPS: In case you're using LE 10.0+, HDMI settings have been moved to cmdline.txt.
