Unofficial LE for RK356x RK3328\RK3399 RK3588(s)

Hi

The images would work on any rk3328 device or they are only for the supported rockchip devices?

Quote from balbes150

It is not clear which SbS model you are writing about.

My bad - I should have mentioned it was the ROCKPro64. Pine sells an add-on wireless module in their store for it. I suspect it's a pretty common combo.

ROCKPro64 1x1 Dual Band WIFI 802.11AC/BLUETOOTH 5.0 MODULE - PINE STORE

Note: This module compatible with ROCKPro64 and Quartz64 Model A SBCs. Based on Azurewave AW-CM256SM Combo Module and made specifically for the ROCKPro64 SBC.…

pine64.com

The mainline LibreELEC includes the module and also one for the ASM1166 PCI card I have plugged into the board for sata drives.

LibreELEC-ARMv8.aarch64-11.0-devel-20230111091039-e014594-rk3399.img

Hello! Very big thanks for your work!

I am using this image for my orange pi 4 lts and it have 10/100/1000Mbps Ethernet ( YT8531C ) 
is any way to add this support in your image or i can do it myself using some instructions?

Testing on orange Pi 4 lts 3GB ram \ 16GB EMMC RK3399-T

Working

-Mpeg2, H264, h265(hevc)

-HDR 10 bit

-4k 60fps

-video up to 200 mbit\sec

Not Working

-LAN (YT8531C )

-WIFI (CDW.20U5622-00)

-BT (CDW.20U5622-00)

Quote from demoss

-LAN (YT8531C )

This will come soon to mainline kernel so it will get added automatically,

Others will not be added until it gets upstreamed to mainline kernel.

You can create a custom image yourself by adding the patches needed for wifi to work.

Hi,

Thank you very much for the image.

I'm starting to tinker with my station-p2 and rock-3a boards.

For start, I'm trying to run it on rock-3a. When using the firefly DTB the image boots and works fine. All except the ethernet port. When changing the DTB to rock-3a, the system doesn't boot at all. Attached is the u-boot and Linux boot output.

Can you help me with this?

I wanted to try and fix the issue myself. Tried checking out the source code at https://github.com/150balbes/LibreELEC.tv, but it looks like that this is an older repository. I've checked the official libreelec repositories as well and I can't seem to be able to find it.

Can you please share the repository with the source code as well? I'd link to get my hands dirty and try to help.

append: boot=LABEL=LIBREELEC disk=LABEL=STORAGE quiet console=ttyS2,1500000 console=tty0 systemd.debug_shell=ttyS2 coherent_pool=2M cec.debounce_ms=5000
Retrieving file: /dtb/rockchip/rk3568-rock-3a.dtb
reading /dtb/roc
kchip/rk3568-rock-3a.dtb
116665 bytes read in 14 ms (7.9 MiB/s)
Fdt Ramdisk skip relocation
## Flattened Device Tree blob at 0x0a100000   Booting using the fdt blob at 0x0a100000   Using Device Tree in place at 000000000a100000, end 000000000a11f7b8
can't found rockchip,drm-logo, use rockchip,fb-logo
WARNING: could not set reg FDT_ERR_BADOFFSET.
failed to reserve fb-loader-logo memory
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000)
Adding bank: 0x1f0000000 - 0x200000000 (size: 0x10000000)
Total: 15261.660 ms

Starting kernel ...

[    3.007234] arm-scmi firmware:scmi: Failed. SCMI protocol 22 not active.
[    3.071226] rk_gmac-dwmac fe010000.ethernet: no regulator found
[    3.071800] rk_gmac-dwmac fe010000.ethernet: Can not read property: tx_delay.
[    3.072492] rk_gmac-dwmac fe010000.ethernet: set tx_delay to 0x30
[    3.073054] rk_gmac-dwmac fe010000.ethernet: Can not read property: rx_delay.
[    3.073695] rk_gmac-dwmac fe010000.ethernet: set rx_delay to 0x10
[    3.081220] mdio_bus stmmac-0: MDIO device at address 0 is missing.
[    3.123442] clk: failed to reparent i2s1_mclkout_tx to clk_i2s1_8ch_tx: -22
[    3.171725] clk: failed to reparent i2s1_mclkout_tx to clk_i2s1_8ch_tx: -22
[    3.290673] arm-scmi firmware:scmi: Failed. SCMI protocol 17 not active.
[    3.371473] mmc0: tuning execution failed: -5
[    3.371873] mmc0: error -5 whilst initialising SD card
[    3.527567] mmc0: tuning execution failed: -5
[    3.527996] mmc0: error -5 whilst initialising SD card
[    4.472890] rockchip-dw-pcie 3c0000000.pcie: Phy link never came up
[    4.490269] pcieport 0000:00:00.0: of_irq_parse_pci: failed with rc=-22

Oleg moved his repo to Bitbucket. I forget the URL, but even if you find it, his habit of summing all changes into a single (date coded) commit means each commit has 1000+ changes and it's impossible to find anything meaningful in his branches. Good luck

Thanks for the response. Unfortunately, bitbucket is not something you can search easily.

Thanks for the heads-up. I think that it would be manageable to fix the DTB.

Hopefully I'll get a hold of the URL and try my luck

Would you be kind enough to share the source repository, so that I can build the dts myself?

I have one TV BOX (RK3566 X96 X6 TV Box Android 11.0 TV Box 4GB 32GB), I want to try to use the LibreELEC on my TVBOX, First I write the image LibreELEC-ARMv8.aarch64-11.0-devel-20230301125115-e014594-rk3566 on TFcard use the BalenaEtcher software at windows 7 system, then I inserd the TFcard in the TVbox , but the TVbox can not start from the TFcard ,so what is the problem? I upload one picture