Posts by boot2k3

LibreELEC.USB-SD.Creator.Win32

I don't think that the problem is in image program

After some time and reboot the same crc errors

micro-SD tested - no errors

The reason was in my micro-sd to usb adapter, I used it for image burning and some reconfiguration. So it doesn't work correctly with micro-sd card more than 8 Gb, after 10 Gb it works incorrectly.

Now I did a fresh install via card reader and backup restore via SD slot and no more CRC errors.

Thank you all for your help.

Quote from bubblegum57

You could try a low level format, eg Low Level Format and zero-filling

This utility mark my 32 gb micro-sd card with bad blocks approximately after 33%

what is wrong?

Quote from Tim_Taylor

I believe it´s caused by internal card reader.

You can try USB pen or buy a new box(best choice)

Quote from bubblegum57

You could try a low level format, eg Low Level Format and zero-filling

Thank you, I will try to perform both of your advice later.

To change the box is not a good idea. It works very well. Just this issue with card I have last month.

I have CRC errors on all of my SD, microsd cards in LE

One of them, during boot process:

Mar 10 09:48:04 LibreELEC kernel: aml_sd_emmc_data_thread : 2586
Mar 10 09:48:04 LibreELEC kernel: mmcblk1: response CRC error sending r/w cmd command, card status 0x900
Mar 10 09:48:04 LibreELEC kernel: end_request: I/O error, dev mmcblk1, sector 9568698
Mar 10 09:48:04 LibreELEC kernel: end_request: I/O error, dev mmcblk1, sector 9568706
Mar 10 09:48:04 LibreELEC kernel: end_request: I/O error, dev mmcblk1, sector 9568714
Mar 10 09:48:04 LibreELEC kernel: end_request: I/O error, dev mmcblk1, sector 9568722
Mar 10 09:48:04 LibreELEC kernel: end_request: I/O error, dev mmcblk1, sector 9568730
Mar 10 09:48:04 LibreELEC kernel: end_request: I/O error, dev mmcblk1, sector 9568738
Mar 10 09:48:04 LibreELEC kernel: end_request: I/O error, dev mmcblk1, sector 9568746
Mar 10 09:48:04 LibreELEC kernel: end_request: I/O error, dev mmcblk1, sector 9568754
Mar 10 09:48:04 LibreELEC kernel: end_request: I/O error, dev mmcblk1, sector 9568762
Mar 10 09:48:04 LibreELEC kernel: end_request: I/O error, dev mmcblk1, sector 9568770

and repeated error:

Mar 10 09:48:04 LibreELEC kernel: [aml_sd_emmc_irq] sd: warning... data crc, vstat:0xe1ff0008, virqc:3fff
Mar 10 09:48:04 LibreELEC kernel: [aml_sd_emmc_irq] @ cmd 18 with ffffffc0a0923170; stop 0, status 4
Mar 10 09:48:04 LibreELEC kernel: [aml_host_bus_fsm_show] sd: err: wait for irq service, bus_fsm:0x8
Mar 10 09:48:04 LibreELEC kernel: aml_sd_emmc_data_thread 2639 sd: cmd:18
Mar 10 09:48:04 LibreELEC kernel: [aml_sd_emmc_data_thread] aml_sd_emmc_data_thread() 2655: set 1st retry!
Mar 10 09:48:04 LibreELEC kernel: aml_sd_emmc_data_thread : 2586
Mar 10 09:48:04 LibreELEC kernel: sd: req failed (CMD18): -84, retrying...

I don't believe what all my cards have bad blocks, some of them are new one.

Also fsck doesn't show any errors

Are any solution available for this errors?

Looks like old fd628 driver used in 8.90.5 build, advanced settings in FD628 addon doesn't work for X92 device

Quote from dodo95

s25003 Have you tried Custom EDID [LibreELEC.wiki]

I will try to test it later and delete lower resolution, but not sure if it choose correct one(1080p50Hz)

Quote from s25003

I am not sure but don’t you med to first start TV and AVR to be able to receive the correct HDMI handchake chain to the S912 box ?

The box can then output the correct output to the TV matchning the video resolution and color depth.

I can, but my wife likes to press three power buttons in different sequences

Is it possible to fix resolution and framerate at startup?

If I start S912 box before TV and AVR than I receive 720p60hz after LE started. But I need 1080p50Hz.

I triedfw_setenv hdmimode 1080p50hz and fw_setenv outputmode 1080p50hz, but it doesn't work in that case

If you use build 8.90.4 than You need to configure your remote:

LE9.0 remote configs ir-keytable Amlogic devices

Quote from serjy

Hello

Code

LibreELEC:~ # ir-keytable -a /storage/.config/rc_maps.cfg -s rc0
/sys/class/rc/: No such file or directory

What could it mean in fresh LE 8.90.2?

All files in proper places, all they and DTB was cheked with 8.90.4, and all was fine (except stability..)

Thank you

For 8.90.2 you need to use old dtb and old remote.conf

Quote from azido

Just to make sure: do i still need to set up my remote in rc_keymaps with assigned letters to my buttons (KEY_A, KEY_B etc.) ?

0x7076b KEY_C
See my example in post LE9.0 remote configs ir-keytable Amlogic devices

Lircmap.xml and keymaps.xml are optional and can be configured only for incorrect buttons or for you desires(in my example this buttons marked as new). See also example in post LE9.0 remote configs ir-keytable Amlogic devices

Quote from tgrzebien

Unfortunately remote.conf don't work with this build on mecool m8s pro+. I installed 9.0-Leia-testing-Gendo-20-10-2017 and LibreELEC-S905.arm-8.2-8.2.3.1 and there remote working on start.

in that case you are doing something wrong.

1. You need to use latest dtb (Device tree) for 8.90.4 build

2. You need to config you remote as described in LE9.0 remote configs ir-keytable Amlogic devices. (remote.conf doesn't work anymore)

Quote from azido

Yeah, in kodi, but when using eventlircd and mapping KEY_I to the info button of the remote, it didn't work, that's why i asked. Happened for a lot of buttons too, where i mapped letters to the scancodes and assigned functions to them in keyboard.xml.

If you use 98-eventlircd.rules as HiassofT said before than it recognize remote as keyboard and you can use keyboard maps

For me it works

Quote from frequenzy

what keymap should be used to enable the mouse button?

BTN_MOUSE
But I don't know how to config buttons to use them as mouse

Quote from azido

Hello,

so, does that mean, after disabling the translation, as long as i will use any of the keycodes in this list http://github.com/tirithen/xbmc/…evices.cpp#L126 mapped in my rc_keymap file, for example

0x88fd0f KEY_I

when i press that button, kodi will receive an "i" as i would just type it on a keyboard and i can map <i>Info</i> in keyboard.xml?

That would save me a lot of trouble.

yes, you are right

KEY_I is already mapped for Info, so you can left default function or remap it in keyboard.xml on another function if required

But it's S905x, not S912.

Marciano needs another dtb, not x92 dtb