Posts by r4w

mglae I flashed another microsd, set up the uenv.ini file as follows:`

dtb_name=/dtb/meson-gxl-s905x-p212.dtb
bootargs=boot=UUID=1507-4017 disk=UUID=f426ba96-ae14-42f3-8d9f-269a100f407b quiet nosplash ssh systemd.debug_shell=ttyAML0 console=ttyAML0,115200n8 console=tty0

And I can reproduce the problem.

However, if I add "textmode" to bootargs after writing the microsd, ssh is able to start.
I also used a diverse laptop (windows) and LibreELEC USB-SD Creator this time.

I enabled Samba but that doesn't seem to work either, so unable to extract the logs.
I am kind of accepting that is a problem with my box at this point

Quote from mglae

Should be automatically created by tmpfiles at boot. Please post logs if this occurs again (accessible via samba share without ssh)

Interesting. The /storage/.ssh and /var/empty directories which are included in the same file do exists without any manual intervention from my side. I am planning to flash other microSD soon.

Thanks for the feedback chewitt, I appreciate it. I am planning to install this image in another microSD, so I will report back if I can still reproduce the issue, in case someone has the same problem.

Maybe there isn't much people using S905X with the latest version, but that is me speculating at this point! You know better for sure.

I used BalenaEtcher to write the image the SD card and, truth is, I am testing various *Elec distributions and Armbian, but I had the SSH issue only with this one.

Is the ssh folder already created in the image file or is it created at the first runtime? Is there a way to expand/mount the image to inspect it? This is what I used: LibreELEC-AMLGX.arm-11.0.3-box.img.gz

So this seems to be a bug to me but I wanted to confirm with you before I raise one (and I find the instructions to do so).

I enabled textmode, nosplash and removed quiet, to watch the boot.

This is what I was presented with (sorry for the dusty micro-screen, all I had to work with a keyboard):

Basically, sshd was trying to restart all the times.

I checked the journal and there was a no such file or directory error while attempting to create the SSH keys:

Checking the folders, ssh folder was missing under /storage/.cache:

I created the folder, restarted ssh and it seems to be fine so far:

Is that a known issue? If not, how do I report it?
Thanks!

Quote from Bub4

Would have been too easy. Sorry I can‘t help further I‘m afraid. Good luck

No worries, it was a good shout! The issue is puzzling me. I think I will try to attach a keyboard and run it in textmode to see if I can see the ssh daemon running and, if not, try to start one manually (I am excluding a local firewall issue). Unless there are other things I can check!

Quote from Bub4

Try

ssh-keygen -R IP.of.the.device

I guess you connected to the same device before via ssh?

I am getting a connection refused as opposed to ssh issues in connecting to the box itself.
But it was still a good point to check and no, I haven't used ssh with that IP before:

````

ssh-keygen -R 192.168.1.X

Host 192.168.1.X not found in /Users/X/.ssh/known_hosts

Hi all,

I am testing Libreelec 11 on an old S905X box (Zen 11 pro) and I installed it in a new separate micro SD card.

Libreelec starts and boots up, everything is fine except for the wireless but I am not bothered about that as I am able to use the LAN instead.

However, when I try to enable SSH on the first setup wizard, save the configuration and check the config again to set up the password, it goes back to Off.
I changed the SSH password, enabled SSH again, and yet it's still Off.

I added "ssh" to the uEnv.in file but, while I can ping the IP address from my laptop, I always get a connection refused on port 22, like if the service is unable to run.

I am out of ideas, any suggestions on what to try next? Is this a known issue? Thanks!

Makes sense now thanks!

vpeter I can't see it with the current kernel config or maybe I'm doing something wrong:

I'm simply running make menuconfig like this: linux-6d8fbb4ee61a7779ac57b5961e076f0c63ff8b65$ PROJECT=Amlogic DEVICE=S905 ARCH=arm make menuconfig

Quote from Menion

I have not found yet the time to bring a 4.19 to a boot on my S912 devices. When I tried the 4.18 Ethernet was just down. Can you give a shot with CoreELEC? There are people there confirming that they solved the issue

I don't have a S912 device yet, I'm afraid. I was just considering to buy it and checking if it was working.

I'm wondering if there still this problem as I'm considering buying a secondary box. Have someone tried it with the latest version of Armbian? Menion have you checked out if there is still the issue with kernel 4.19?

Quote from vpeter

You could enable IP: Foo (IP protocols) over UDP and you will get NET_UDP_TUNNEL too.

I will check again, but in the kernel config I didn't spot that either.

I'm exploring wireguard too while looking into improving crypto speeds, but I can't see in the Amlogic kernel configuration (make menuconfig) the option CONFIG_NET_UDP_TUNNEL which is a requirement (Installation - WireGuard). All the other kernel requirements are satisfied.

Would be possible to update the title and first page to reflect the current versions available? Thanks

Got it, thanks again

Thanks both, I didn't believe it was a problem just to add the module (without loading it by default). I'll do some experiments.

Hi all,

It's a bit I didn't post but I have been busy moving house. I'm doing some tests with my 905X box with Openvpn and I'm wondering if it would be possible to have the cryptodev kernel module included in the next releases.

This has been briefly discussed in this topic VPN help and the module may not work well with the current kernel (reference: Gentoo Forums :: View topic - Gentoo for Amlogic S9xx (TV box S905\S905X\S912)), but I would be happy to experiment more.

Thanks!