Posts by thoradia

  • Thoradia Add-ons

    Quote from edjalmo

    So, 2 days running without freezings and reboots (image). I'm running Sonarr and Radarr with MemoryHigh=125M and MemoryMax=150M too. But not running Bazarr, just Radarr, Sonarr, Jackett and Transmission. And now doing the downloads direct to external disk 😁

    If the memory usage stay at ~80% I will do nothing, but if it increase I will try add a WatchdogSec= in Sonarr/Radarr/Jackett for something like reboot every day, or maybe learn how I do this using .timer

    Maybe I try add Bazarr to run just during at dawn and in the same time I stop Kodi (to prevent the freeze), but not for now.

    It's a bad ideia put MemoryHigh=125M and MemoryMax=150M by default in Sonarr, Radarr and Bazarr too? For at least for Raspberry devices (I don't kow how many LibreELEC devices have little memory) and putting a disclaimer in readme section, explaining it have to add cgroup_enable=memory in /flash/cmdline.txt to make this work (just an idea).

    Thanks again for helping :)

    I was waiting for your feedback to set MemoryHigh and MemoryMax in Bazarr, Radarr and Sonarr

    cgroup_enable=memory at the end of /flash/cmdline.txt is documented in this thread

  • Thoradia Add-ons

    According to your log, installation starts at :06, unpacking starts at :22, installation is interrupted at :24

    Mono is a 50 MB zip file, which is downloaded and unzipped

    Mono binaries are then unzipped from about 50 MB to several hundreds MB

    Give this a minute or two

    To verify that Mono is correctly installed, use systemctl status tools.mono

  • Thoradia Add-ons

    Quote from edjalmo

    What I did was let the download and upload rate be 0 during the day and in the maximum during at dawn.

    But at dawn everythings it run, rss sync of sonarr/radarr, bazarr downloading subtitles.

    What is better: download the content direct to external drive or download to sd card and after to external drive?

    Do not overload the bus and SSD with IO

    Restrict IO to 2-3 Mb/s in Transmission

    Prefer external to SSD

  • Thoradia Add-ons

    Quote from edjalmo

    I use a external disk for storage. But transmission download the content in sd card and after move it to my external disk (but although it is still seeding until ratio 1:1 in sd card). When you said use external drive you say the transmission download folder too?

    You right! I'm expecting much from it! It have just 1gb of RAM.

    Using cron?

    But this way I will lost some rss sync and maybe lost content, or am wrong?

    Disable Transmission (with the UI) while the other processes are very active

  • Thoradia Add-ons

    Quote from markj24

    Hi

    Just wondering where i could find so more info or a how to for thoridia vpn network interface addon. the only thing in the config is username, password and openvpn file. i've added all 3 and see no indication it is connected or how to bind specific addons to this network. i'm looking to only run sonarr, radarr, jackett and qbittorrent through the vpn. maybe i'm reading the description wrong but from my understanding this is what it does... allows specific addons to bind to this network interface and be routed through a vpn and the rest of the system uses the regular internet connection. can someone please correct me if i'm wrong and this isn't possible and if it is point me in the right direction to getting it set up this way if it is possible

    Thanks

    Configure it with a OpenVPN configuration file, userid and password

    This will create the the thoradia-vpn interface

    You can check it is up with ifconfig or ip addr

    To get the default public IP: curl -s https://ipinfo.io/ip

    To get the public IP of thoradia-vpn: curl -s https://ipinfo.io/ip --interface thoradia-vpn

    They should be different

    To configure qBittorrent to use thoradia-vpn add Connection\Interface=thoradia-vpn in /storage.kodi/userdata/addon_data/service.qbittorrent/.config/qBittorrent/qBittorrent.conf

    qBittorernt will work only if thoradia-vpn is up.

  • Thoradia Add-ons

    I have no idea what caused filesystem corruption

    But writing a lot to SSD is not a good idea, especially on a Raspberry Pi where network and storage share the same bus

    Try using an external disk for storage

    As for memory, Bazarr, Jackett, Sonarr, Radarr each use about 100MB, and more than 400MB together

    Add Kodi and Transmission, and you easily reach the memory capacity of a Raspberry Pi

    Try MemoryMax=100 and MemoryHigh=125 for Bazarr, Jackett, Sonarr, Radarr and Transmission

    Also try phasing activity of Bazarr, Jackett, Sonarr, Radarr and Transmission

  • Thoradia Add-ons

    edjalmo

    I have restricted Jackett memory usage to MemoryHigh=125M and MemoryMax=150M in system.d.

    To activate this restriction on Rasberry Pi, add cgroup_enable=memory at the end of /flash/cmdline.txt

    Please let me know if you can activate memory management and if MemoryHigh and MemoryMax are appropriate for Jackett

    vpeter Thank you for your help with this

  • Thoradia Add-ons

    Quote from edjalmo

    So... My hardware is RPi 3b. I can run sonarr, radarr, bazarr and transmission without problems. But if a execute jackett, in every rss sync of sonarr/radarr a lot of memory is allocated and not release, and in some point (after some hours) LibreELEC freeze. In this jackett page have a systemd file for low powered system. The change I want to make is this to see if it's an improvement.

    This is worth investigating

    MemoryHigh and MemoryMax are also documented here

    What does --optimize-all do?

    If you can fix the freeze then submit a pull request at github or post your service.jackett.service here

  • Thoradia Add-ons

    I did not build add-ons for WeTek since a long time

    I will start a build now and let you know when it is available

  • Thoradia Add-ons

    Quote from edjalmo

    Other things that I noticed:

    In Sonarr logs always says "Mono is not running with --debug switch". I tried adding --debug in the sonarr service (like this radarr example) but this persists. Before using LibreELEC I used OSMC and added that resolved.

    Every time I open the Jacket this warning appears: "Jackett is running with root privileges. You should use Jackett as an unprivileged user."

    I also tried a solution. Change the privileges with chown -R with another user / group, but LibreELEC did not allow it.

    These warnings do not seem to interfere with performance (not that I've noticed), but are warnings.

    As for the --debug switch in Lidarr, Radarr and Sonarr, what good would it bring?

    As for root privileges, everything runs with root privileges in LibreELEC

  • Thoradia Add-ons

    Quote from edjalmo

    I can put sonarr and radarr in automatic updates?

    I know you will launch the new release as soon is possible (and thanks for that!!!). But if I update what happens when you update too?

    Yes, enable automatic updates wherever you can (Jackett, Lidarr, Sonarr, CouchPotato, Hedaphones, Medusa)

    I usually update to the latest version, so nothing should happen to installed add-ons

  • Thoradia Add-ons

    Quote from firecheesesauce

    I just upgraded to Libreelec 9.0 and my sonarr and radarr stopped working. I tried uninstalling the app and reinstalling but no go. SABnzbd works and I tried couchpotato and that worked but I have everything I want setup on sonarr and radarr. I would rather not have to do a fresh install of Libreelec if there's another option available.

    First make sure you restarted Kodi or rebooted since you updated, then check for updates in Kodi add-on manager, or update the Mono, Radarr and Sonarr add-ons to version 9.0.x.

    If this does not fix your problem then specify your LibreELEC project (Generic, RPi, RPi2, etc), the versions of the Mono, Radarr and Sonarr add-ons, and provide the output of journalctl -u service.radarr