Posts by stevensen

Thank you for your answer!
I did it all again including setting the resolution and now the resolution, the sound and the Netflix addon are working(over ethernet). Only the usb hard disk I can't mount yet, I'll try that again and then maybe open a new thread or something.

Hello,

I need to update my Rock pi 4 SE to Libreelec 11 and Kodi 20 to watch Netflix (at least I think so).

I have installed the new version for testing, but I encountered several problems. I can't switch to HD resolution, there is no audio and the usb hard drive is not recognised.

Under Libreelec 10 I was able to fix the resolution via edid (which I can't do now), and hard disc and audio were no problem.

Is there a chance to fix all this problems with the new version or are there any instructions?

Happy new year!

After I made a backup. I started a new attempt and now it works!!

Thank you very much for help!

thanks for help!

I had tried both variants, each time the computer did not start. Only when I had the Conf back in the original state it worked again.

I make a test copy today and try it again.

Thanks for the answer!

I am so far as seen in the picture.

What do now with this line:

drm.edid_firmware=HDMI-A-1:edid/edid-HDMI-A-1.bin video=HDMI-A-1:D

I do not understand yet.

And on my rock 4 exists this file:

/flash/extlinux/extlinux.conf

With this content:

LABEL LibreELEC
  LINUX /KERNEL
  FDT /rk3399-rock-pi-4b.dtb
  APPEND boot=UUID=0503-4902 disk=UUID=8ff85d86-0886-4367-affc-e7e92877481a quiet console=uart8250,mmio32,0xff1a0000 console=tty0 coherent_pool=2M cec.debounce_ms=5000

What should I do now?

Excuse my cluelessness <:(

ok here:

http://ix.io/4hY1

Hello,

I have physically connected a Hdmi cable on the running TV

Should not be a Hdmi connector / driver to see?

login as: root

[email protected]'s password:

##############################################

# LibreELEC #

# https://libreelec.tv #

##############################################

LibreELEC (official): 10.0.2 (RK3399.arm)

LibreELEC:~ # tail /sys/class/drm/*/status

connected

LibreELEC:~ #

Thanks for your answer

somehow it does not work

LibreELEC:~ # getedid create

-sh: getedid: not found

I try your postet link

Hello,

I am still a beginner in Librerelec 10.0.2 and Linux.

I have here a Rock 4 SE and still have a problem with Hdmi and the resolution.

When the TV is on, the resolution (HD) is set correctly, but when the Rock 4 is recording and I turn on the TV later, a smaller resolution is set.

The Rock can not read the correct values from the TV off, it needs an edid or something like that.

How can I fix this ? Please keep in mind I am a beginner

Hello,

In radxa-wiki I found how I can switch e.g. Leds etc., I need that later for a fan control.

Have just other problems.

Currently I do not know how to start the Rock 4 SE when it is in suspend mode.

Is there a way to connect a reset button and if so how?

When it is supposed to record, it wakes up and records, but then stays awake.

Is it possible to put it back to sleep via script?

I used DVB-C.

I disconnected the USB hard drive and used a different port for the Xbox tv-tuner stick.

And then it ran and I think he also found all channels!

Then I reconnected the hard drive and it still worked. Maybe it's a power problem while scanning.

I hope I am in the right forum here.

I have a Rock 4 SE here and would like to run it with an Xbox TV tuner.

Under tvheadend I see the driver and it has also scanned channels. Unfortunately not all channels were there.

After I tried to run it with a fresh Librelelec today, it can't find any muxes or servies.

What could be the error?

Thank you very much for your answer and the advice.

I don't know this system and have to read up on it first and will definitely get back to you.

Hello,

Is it possible to access the GPIO on the Rock pi 4 SE via script under libreelec, as on the Raspberry PI?

I am a beginner in libreelec and Rock 4 SE and have a problem installing a Sundtek driver.

I got LibreELEC-RK3399.arm-10.0.2-rock-pi-4 to work with Kodi and Tvheadend on a Rock 4 SE. However, the driver installation of the Sundtek SkyTV Ultimate Dual (2x DVB-S/S2/S2X) didn't seem to work. The drivers do not appear in the Tvheadend overview.

Has anyone experience with this hardware and software installation and could help me?