I cannot get LibreELEC to boot (just hangs on the amlogic logo) with that p200 dtb.
I have MXV+ device 1G, 1 Gbit (MXV+ (MXV Plus) Review: Android TV Box powered by 64bit Amlogic S905 • AndroidTVBOX.eu). Android says that it´s p201 board. But I have LE configuration with gxbb_p200_1G_1Gbit_RealtekWiFi.dtb device tree and everything works great.
Yes, thanks. I didn't remember, that instructions are for s905 boxes...
Hi, still is here maybe solution by 150balbes. Don´t worry Russian language and go to bottom of web page, there is english language part.
s905_multi_boot · 150balbes/Amlogic_s905 Wiki · GitHub
This solution I have used on my MXV+ box, because I had similar problems like you.
Hi kszaq,
thanks for your work. Last dev build seems very stable.
MXV+ S905 1GB 1Gbit::
DTS, DD, DTS-HD MA passthrough is working, CPU temperature works, no pops/clicks, no A/V sync issue (test lot of files), no memory leaks.
Perfect...
But I still have 2 probs....
1- No CEC (LG TV and Box plugged to Yamaha receiver)
2- I only see English as international language!
Any help?
Overall....very nice work
Hi,
I have the same configuration, and yes the same behavior. This is not problem kszaq LE. The same "problem" is with all ELEC and its versions (OpenELEC, LibreELEC).
Ad1. TV remote CEC not working. BUT Yamaha remote works! 
(If you have your box connected to Yamaha.)
Ad2. You must install KODI language addon.
Hi kszaq!
I updated to version 009 from you last development version on my MXV+ (MXV Plus) just now. I download files LibreELEC-S905.aarch64-7.0.2.009.img.gz and gxbb_p200_1G_1Gbit_RealtekWiFi.dtb and simply put both files to update folder without rename gxbb_p200_1G_1Gbit_RealtekWiFi.dtb to dtb.img (as I read on JohnSnow post at first side).
Everything seems all right, all works properly!
Thank you for your perfect work!
I also have a question for an older MXQ Pro 4k box:It's an MXQ Pro that has the problem with the reset button not soldered/not working (holding reset doesn't go into recovery)
Is there any chance at all to have such a box boot LibreElec from SD or USB, or is it only possible to boot to recovery and install Libreelec on internal memory ?
Yes, I hope so.
If you have a problem with boot to LE, you can try this procedure:
LibreELEC
and additional information here:
LibreELEC
I used this device tree:gxbb_p200_2G_1Gbit.dtb If my understanding is good: Tronsmart Vega S95 telos has 2 GB internal memory with Gigabit LAN, so the mentioned tree should be good.
But correct me if I am wrong.
Maybe I can change the SMB to NFS as kszaq wrote it here.
Hi, I think Tronsmart Vega S95 Telos has Realtek Realtek RTL82XX ethernet and wifi adapter. Try gxbb_p200_2G_1Gbit_RealtekWiFi.dtb
And yes, NFS sharing is better, but I do not think so that is your problem, because SMB sharing works usually properly.
Is there a guide to reinstall android and then I can start again from scratch?
How to use the Amlogic USB Burning Tool to manually update firmware - AndroidPCReview
I briefly tested the 008 and found that
- buffer: now vq remains around 90%, in 007 with the same files vq goes to 0% after some minutes
- in 008 in some video the audio is out of sync, it is ok in 007
- 2 channels audio files with sr>44.1 (tested 48KHz and 96KHz) are not reproduced over HDMI...not testd S/PDIF
Hi, can you upload somewhere some files which have a problem? Because I think, my box with 008 version works properly ...
At the moment I could not get the IR remote control to work.
And remember. If you TV or Receiver supports HDMI CEC, you can control LE via original Remote control from your TV or Receiver. You must only switch on HDMI CEC in setup of TV or receiver.
It´s my use case. It´s very usable
@Whitesak None of your posted links are valid in their present form :sAre these the locations they are supposed to point to?
Yeah, thank you Poida. My mistake. 
I have corrected my links in my post LibreELEC .
The MX Plus box ALWAYS starts Android in safe mode (toothpick method).
The MX Plus box ALWAYS starts Android in safe mode (toothpick method).
Hi Andreaf.
There is my experience how install and running LibreELEC with my box MXV+ (MXV Plus):
1. First - you must create dualboot patch on your box (s905_multi_boot · 150balbes/Amlogic_s905 Wiki · GitHub) . How to: Download two files from Yandex.Disk - aml_autoscript, aml_autosctipt.zip.
Copy both files to SD card. Boot your box to Android, inser SD card. Then you must go to section programs and start Update&Backup , choose file aml_autosctipt.zip and start Update. Box will be rebooted to Android again - it is OK.
2. Next step is copy IMG from LibreELEC-S905.aarch64-7.0.2.007.img.gz. You must unzip file LibreELEC-S905.aarch64-7.0.2.007.img.gz to LibreELEC-S905.aarch64-7.0.2.007.img (use for example 7zip). Then you can use Win32DiskImager and to write IMG to SD Card.
3. Download correct dtb.img from device_trees . On my MXV+ works correctly file gxbb_p200_1G_1Gbit.dtb . After download you must rename it to dtb.img. Then copy dtb.img to your SD card a rewrite original dtb.img there.
4. Switch on your box without inserted SD card. Box will boot to Android. Install to Android some boot application, for example " [root] Simple Reboot" from Google Play Store.
Now insert SD card to box and via Simple Reboot Reboot box to Bootloader (not to recovery)
Box will boot to LibreELEC. I hope so , because this procedure works on my box.
BTW: Special thanks to kszak. Perfect work!!! Thank you.
EDIT: Bad links was corrected. Thanks Poida.
7.0.2.007 Almost there build 007 (2016-09-07)Hi kszak,
thank you for your perfect work. I sent you small coffee or beer donation
Hi kszaq!
Thank you for your perfect work!
Please can you help me with my S905 box MXV+ (MXV Plus)? Where can I find dtb.img for my device?
Thanks
