i have same box but wget http://ix.io/4tpc -O /storage/.config/firmware/brcm/brcmfmac4330-sdio.oranth,tanix-tx6.txt not working ,seems not working ix.io is down
Posts by atari
-
-
Im trying to flash whit multitool my nand whit any libeelec v9,10,11 but it will not start from nand.
Hardvare Mxq r9 - MX4N 8G/1G ZHD 2017-03-18 any tip what is good image for it?
-
Im boot LibreELEC-RK322x.arm-10.0-nightly-20230402-3cb942b-rk322x.img image from sd but cant install it on flash, any tip?
Don't seen any installtoflash command.
I tryer LibreELEC-RK322X.arm-11.0-nightly-20230322-c4a7662-rk322x.img can``'t boot..
-
Thanks, now wifi works but only 2.4, 5ghz&bt not
iw dev wlan0 scan
BSS b8:69:f4:d9:6b:36(on wlan0)
last seen: 42.585s [boottime]
TSF: 0 usec (0d, 00:00:00)
freq: 2412
beacon interval: 100 TUs
capability: ESS Privacy ShortPreamble ShortSlotTime (0x0431)
signal: -34.00 dBm
last seen: 104 ms ago
SSID: neutrino-digital.com
Supported rates: 1.0* 2.0* 5.5* 11.0* 6.0 9.0 12.0 18.0
DS Parameter set: channel 1
ERP: <no flags>
HT capabilities:
Capabilities: 0x102c
HT20
SM Power Save disabled
RX HT20 SGI
No RX STBC
Max AMSDU length: 3839 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: No restriction (0x00)
HT RX MCS rate indexes supported: 0-15
HT TX MCS rate indexes are undefined
RSN: * Version: 1
* Group cipher: CCMP
* Pairwise ciphers: CCMP
* Authentication suites: PSK
* Capabilities: 1-PTKSA-RC 1-GTKSA-RC (0x0000)
Extended supported rates: 24.0 36.0 48.0 54.0
HT operation:
* primary channel: 1
* secondary channel offset: no secondary
* STA channel width: 20 MHz
* RIFS: 0
* HT protection: no
* non-GF present: 0
* OBSS non-GF present: 0
* dual beacon: 0
* dual CTS protection: 0
* STBC beacon: 0
* L-SIG TXOP Prot: 0
* PCO active: 0
* PCO phase: 0
WMM: * Parameter version 1
* u-APSD
* BE: CW 15-1023, AIFSN 3
* BK: CW 15-1023, AIFSN 7
* VI: CW 7-15, AIFSN 2, TXOP 3008 usec
* VO: CW 3-7, AIFSN 2, TXOP 1504 usec
-
wget: can't open '/storage/.config/firmware/brcm/brcmfmac4330-sdio.oranth,tanix- tx6.txt': Read-only file system
-
I add dir & link but still no wifi&bt
-
device is not in list 20190329.L4
CS_H6_TX28_DTX_V1.0
-
On image 11.0.1 wifi drivers not working
Can i add it tru ssh?
-
-
-
TerraTec use for different Hardware the same deviceID. Therefore you cant load successfully the driver. You need another driver:
TerraTec Electronic GmbH Cinergy TC2 stick - DVB Adapters - Cesbo Community
Maybe in a future kernel (>4.19) someone has fixed the TerraTec problem.
i try new kernel too not working
-
-
i try same problem it seems to be driver problem
TerraTec Electronic GmbH Cinergy TC2 stick - DVB Adapters - Cesbo Community
-
I try all 4 driver pack, same
-
same error after update:
Code
Display More[ 721.690677] em28xx 1-1.2:1.0: New device CINERGY TC2 Stick TS Aggregator @ 480 Mbps (0ccd:10b2, interface 0, class 0) [ 721.690679] em28xx 1-1.2:1.0: DVB interface 0 found: bulk [ 721.748459] em28xx 1-1.2:1.0: unknown em28xx chip ID (0) [ 721.804830] em28xx 1-1.2:1.0: reading from i2c device at 0xa0 failed (error=-5) [ 721.804832] em28xx 1-1.2:1.0: board has no eeprom [ 721.861157] em28xx 1-1.2:1.0: Identified as Terratec Cinergy H6 rev. 2 (card=101) [ 721.861160] em28xx 1-1.2:1.0: dvb set to bulk mode. [ 721.861202] usbcore: registered new interface driver em28xx [ 721.867584] em28xx 1-1.2:1.0: Binding DVB extension [ 721.903197] em28xx 1-1.2:1.0: writing to i2c device at 0x82 failed (error=-5) [ 721.903709] em28xx 1-1.2:1.0: writing to i2c device at 0x82 failed (error=-5) [ 721.904174] em28xx 1-1.2:1.0: writing to i2c device at 0x82 failed (error=-5) [ 721.905000] em28xx 1-1.2:1.0: writing to i2c device at 0x82 failed (error=-5) [ 721.905195] em28xx 1-1.2:1.0: writing to i2c device at 0x82 failed (error=-5) [ 721.922176] em28xx 1-1.2:1.0: reading from i2c device at 0x52 failed (error=-5) [ 721.922673] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 721.922675] drxk: i2c write error at addr 0x29 [ 721.933321] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 721.933323] drxk: i2c write error at addr 0x29 [ 721.944572] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 721.944574] drxk: i2c write error at addr 0x29 [ 721.955821] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 721.955823] drxk: i2c write error at addr 0x29 [ 721.967071] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 721.967072] drxk: i2c write error at addr 0x29 [ 721.978072] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 721.978074] drxk: i2c write error at addr 0x29 [ 721.989321] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 721.989323] drxk: i2c write error at addr 0x29 [ 722.000549] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 722.000551] drxk: i2c write error at addr 0x29 [ 722.011423] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 722.011425] drxk: i2c write error at addr 0x29 [ 722.022695] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 722.022697] drxk: i2c write error at addr 0x29 [ 722.033448] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 722.033450] drxk: i2c write error at addr 0x29 [ 722.044173] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 722.044175] drxk: i2c write error at addr 0x29 [ 722.054695] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 722.054697] drxk: i2c write error at addr 0x29 [ 722.065946] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 722.065948] drxk: i2c write error at addr 0x29 [ 722.076322] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 722.076324] drxk: i2c write error at addr 0x29 [ 722.087569] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 722.087571] drxk: i2c write error at addr 0x29 [ 722.098069] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 722.098071] drxk: i2c write error at addr 0x29 [ 722.108445] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 722.108447] drxk: i2c write error at addr 0x29 [ 722.119695] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 722.119697] drxk: i2c write error at addr 0x29 [ 722.130945] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 722.130947] drxk: i2c write error at addr 0x29 [ 722.141579] drxk: Error -5 on power_up_device [ 722.141581] drxk: Error -5 on init_drxk [ 722.141581] drxk: frontend initialized. [ 722.144207] tda18271 10-0060: creating new instance [ 722.144426] em28xx 1-1.2:1.0: writing to i2c device at 0xc0 failed (error=-5) [ 722.144429] tda18271_read_regs: [10-0060|M] ERROR: i2c_transfer returned: -5 [ 722.144429] tda18271: Error reading device ID @ 10-0060, bailing out. [ 722.144431] tda18271_attach: [10-0060|M] error -5 on line 1283 [ 722.144432] tda18271 10-0060: destroying instance [ 722.144435] em28xx: Registered (Em28xx dvb Extension) extension [ 722.147610] em28xx 1-1.2:1.0: Registering input extension [ 722.147616] em28xx: Registered (Em28xx Input Extension) extension LibreELEC:~ #
-
on x86 libreelnec 8.90.004 9.0 kernel 4.18.3 i get errors:
Code
Display More[ 10.466241] em28xx 1-1.2:1.0: writing to i2c device at 0x82 failed (error=-5) [ 10.466894] em28xx 1-1.2:1.0: writing to i2c device at 0x82 failed (error=-5) [ 10.467239] em28xx 1-1.2:1.0: writing to i2c device at 0x82 failed (error=-5) [ 10.467739] em28xx 1-1.2:1.0: writing to i2c device at 0x82 failed (error=-5) [ 10.468239] em28xx 1-1.2:1.0: writing to i2c device at 0x82 failed (error=-5) [ 10.483996] em28xx 1-1.2:1.0: reading from i2c device at 0x52 failed (error=-5) [ 10.484538] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 10.484540] drxk: i2c write error at addr 0x29 [ 10.495747] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 10.495749] drxk: i2c write error at addr 0x29 [ 10.507045] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 10.507047] drxk: i2c write error at addr 0x29 [ 10.518246] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 10.518248] drxk: i2c write error at addr 0x29 [ 10.529495] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 10.529497] drxk: i2c write error at addr 0x29 [ 10.540245] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 10.540247] drxk: i2c write error at addr 0x29 [ 10.551494] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 10.551496] drxk: i2c write error at addr 0x29 [ 10.562745] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 10.562747] drxk: i2c write error at addr 0x29 [ 10.573620] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 10.573623] drxk: i2c write error at addr 0x29 [ 10.584871] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 10.584873] drxk: i2c write error at addr 0x29 [ 10.596118] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 10.596120] drxk: i2c write error at addr 0x29 [ 10.606940] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 10.606942] drxk: i2c write error at addr 0x29 [ 10.618119] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 10.618121] drxk: i2c write error at addr 0x29 [ 10.629369] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 10.629372] drxk: i2c write error at addr 0x29 [ 10.640257] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 10.640259] drxk: i2c write error at addr 0x29 [ 10.651493] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 10.651494] drxk: i2c write error at addr 0x29 [ 10.662747] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 10.662749] drxk: i2c write error at addr 0x29 [ 10.673628] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 10.673630] drxk: i2c write error at addr 0x29 [ 10.685574] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 10.685576] drxk: i2c write error at addr 0x29 [ 10.696900] em28xx 1-1.2:1.0: writing to i2c device at 0x52 failed (error=-5) [ 10.696902] drxk: i2c write error at addr 0x29 [ 10.707913] drxk: Error -5 on power_up_device [ 10.707916] drxk: Error -5 on init_drxk [ 10.707916] drxk: frontend initialized. [ 10.709606] tda18271 9-0060: creating new instance [ 10.709870] em28xx 1-1.2:1.0: writing to i2c device at 0xc0 failed (error=-5) [ 10.709872] tda18271_read_regs: [9-0060|M] ERROR: i2c_transfer returned: -5 [ 10.709873] tda18271: Error reading device ID @ 9-0060, bailing out. [ 10.709874] tda18271_attach: [9-0060|M] error -5 on line 1283 [ 10.709875] tda18271 9-0060: destroying instance [ 10.709878] em28xx: Registered (Em28xx dvb Extension) extension [ 10.712633] em28xx 1-1.2:1.0: Registering input extension [ 10.712639] em28xx: Registered (Em28xx Input Extension) extension
-
hi
I install on x86 libreelnec dvb 8.2 kernel 4.11.12, but seems it not see card in tvheadend
Code
Display Morelsusb -v Bus 002 Device 003: ID 0ccd:10b2 TerraTec Electronic GmbH Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x0ccd TerraTec Electronic GmbH idProduct 0x10b2 bcdDevice 1.00 iManufacturer 1 CINERGY TC2 Stick iProduct 2 TS Aggregator iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 46 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 500mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 4 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 0 bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x84 EP 4 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x85 EP 5 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 0 bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 can't get debug descriptor: Resource temporarily unavailable Device Status: 0x0000 (Bus Powered)
i try :
Codecd /strage/.config/firmware wget -c 'https://raw.githubusercontent.com/OpenELEC/dvb-firmware/master/firmware/dvb-demod-si2168-b40-01.fw' wget -c 'https://raw.githubusercontent.com/OpenELEC/dvb-firmware/master/firmware/dvb-demod-si2168-02.fw' wget -c 'https://raw.githubusercontent.com/OpenELEC/dvb-firmware/master/firmware/dvb-usb-it9303-01.fw'
but didnt help