Posts by omphi

Found the old df -h from before cleanup:

pi:~ # df -h
Filesystem                Size      Used Available Use% Mounted on
devtmpfs                362.3M         0    362.3M   0% /dev
/dev/mmcblk0p8          511.7M    142.2M    369.5M  28% /flash
/dev/mmcblk0p9          968.3M    952.3M         0 100% /storage
/dev/loop0              131.1M    131.1M         0 100% /
tmpfs                   367.8M         0    367.8M   0% /dev/shm
tmpfs                   367.8M      7.0M    360.9M   2% /run
tmpfs                   367.8M         0    367.8M   0% /sys/fs/cgroup
tmpfs                   367.8M      1.9M    365.9M   1% /var
tmpfs                   367.8M         0    367.8M   0% /tmp
/dev/mmcblk0p16          59.1M      6.8M     52.3M  11% /var/media/boot1
/dev/mmcblk0p18         485.4M    341.7M    114.3M  75% /var/media/share
/dev/mmcblk0p17           1.9G    709.6M      1.1G  39% /var/media/root1
/dev/mmcblk0p14          78.8M     21.7M     57.1M  28% /var/media/boot-rbp2
/dev/mmcblk0p13         968.3M      1.2M    901.0M   0% /var/media/mmcblk0p13-d4898227-c197-4ddb-9
/dev/mmcblk0p15           2.4G    538.7M      1.7G  24% /var/media/root-rbp2
/dev/mmcblk0p10          67.9M     21.0M     47.0M  31% /var/media/boot0
/dev/mmcblk0p7            4.6G      4.0G    398.0M  91% /var/media/root
/dev/mmcblk0p12         511.7M    297.2M    214.5M  58% /var/media/mmcblk0p12-D2F8-101F

Please note that this was just after jeg purged the thumbnails.

I use this to view photos as well as watch videos. So it will get a bunch of thumbnails over time. I would like to automatically clean out old ones or maybe set the thumbnail cache to some max size. E.g. 200MB.

Maybe it is possible to place thumbnails on a separate drive? Or even better: on NFS share, so that I can put it on my NAS.

Hi,

I have a raspberrypi with libreelec.

The filesystem on /storage is suddenly full.

Space is taken up by .kodi/userdata:

# du -scm /storage/.kodi/*

43 /storage/.kodi/addons

1 /storage/.kodi/media

1 /storage/.kodi/system

55 /storage/.kodi/temp

852 /storage/.kodi/userdata

949 total

Mostly thumbnails.

Is there any way I can have these thumbnails take up less space? Or maybe have libreelec clean this automatically?

Lots of stuff stops working when the disk is filled.

Please advise.

Quote from Jocke.Sve

Settings => Player / Subtitles

That works.

It would be better with a background box around subs. Where is the appropriate place to place a feature request for this?

Where do I change this? I have not been able to find this under Settings/Options.

Hi,

I am trying to watch some videos that have foreign subtitles "burned in" to the actual video frames.

I wish to use subtitles in my own language and have those in .srt files.

However, when I enable my own subtitles, they are shown on top of the original foreign subtitles in a way that makes both unreadable. Both are white text.

So I am thinking that maybe it is possible to add a black background box around the subtitles, thus making the original subs less visible. Example of what I mean is here:

https://qph.fs.quoracdn.net/main-qimg-0a0e…ff345405cb8358e

If this is not possioble, then maybe just to increase the font size and outline/stroke width as well as to change the font color might make a huge difference.

How can I do these things in LE/kodi?

Resetting audio settings made the analog audio work! Thanks.

Quote from popcornmix

amixer: "allows command-line control of the mixer for the ALSA soundcard driver"

It won't affect kodi which doesn't use ALSA for hdmi or analogue audio.

OK. That makes sense.

So are there any other CLI tools to adjust volume in LE/kodi?

Quote from popcornmix

Ignore alsa mixer. Kodi doesn't use alsa for audio (it uses openmax).

Volume on analogue does work, so it's possible you have custom settings that are affecting it. A debug log may be useful.

But to start with I'd suggest using the "reset settings to default" option in the system/audio settings page, and just change the output device to analogue.

If that doesn't work then renaming /storage/.kodi to /storage/.kodi_back and restarting kodi will start from completely clean settings.

You can then set audio output to analogue and see if it's any different. If not you can rename back to .kodi to get back to your original settings.

Sure, alsamixer does not work. But what about amixer? Shouldnt that work?

Will try resetting audio settings to default.

I have already tried just setting output to analog. Does not make a difference. Then I just have no sound (or extremely low)

Quote from TheWojtek

Perhaps passthrough is still enabled.

What is passthrough and how do i check if it is enabled?

Quote from awiouy

It works fine here (jack to amplifier).

Are you sure about the cable, the volume of the receiving end?

Thanks for your response.

Yes, I am certain that the cable works. I have indeed changed the cable just to make sure. However, that did not make any difference. And I have verified that the cable works by attaching another audio source. E.g. a laptop and an iphone. Both works just fine.

Do you also use a raspberrypi? If so, can I ask which model?

If you are able to enable SSH connectivity to your LE machine, will you try and connect via SSH and type "amixer" in the terminal and paste the output? For me it fails. I would be very interested in seeing if it also fails at your end. If it does, this is likely not the source of the problem. If it does NOT fail or if it fails with some other error, then that is a known difference and maybe related to the source of the problem.

Nothing?

No one has tried using analog output in LE?

Please, if you have used analog output and it IS working for you, I would also love to hear from you. Just to know if it is working AT ALL. Maybe it is not really implemented?

Note that I found this other post in here that seems related:

Raspberry 3 - very low analog volume

However, no solution was found here.

greenbag (greenbag) suggests to run alsamixer but this is not present in LE.

They then suggest using amixer instead which I already tried. However, it fails due to missing 'default' as described above.

Hi,

I am running LibreELEC on my raspberrypi.

I have a TV connected via HDMI and audio output set to output on BOTH analog output (3.5mm jack) and HDMI.

The output on HDMI works fine and audio is going to the TV. However, the volume on the analog output is extremely low. So low that I thought the output simply did not work. But if I turn up the volume to max on my physical amp, I can barely hear the signal - but it IS there.

Adjusting the volume inside LibreELEC/Kodi using my volume buttons on the keyboard does nothing to the volume on the analog output. But it works just fine for adjusting volume on HDMI output. Please note that it is NOT my TV volume I adjust here. It IS inside LibreELEC/Kodi. I can also adjust my TV speaker volume independently.

For audio output in LibreELEC I have also tried setting it to analog only, but that does nothing to the volume. Only mutes the HDMI.

I have tried enabling SSH and then connect to the pi and then I tried starting the following programs:

alsamixer (not present)

aumix (not present)

amixer: present but failed with the following error:

amixer: Control default open error: No such file or directory

How do I fix this?

One fix would be to somehow set the volume to 100 % on the analog audio output. Because then I can just adjust the actual volume on my physical amp.

I hope you can help.

Thanks.