TVHeadend issues

Cryptic · October 14, 2017 at 4:24 PM

Hi,

need some help getting TVHeadend working. I've got a DVBSKY S960 tuner. If I do a fresh LE install, followed by a TVHeadend 4.2 install and run the wizard, it finds services okay. If I map to channels, that's okay, although the numbers are messed up. Nothing I do regarding bouquets makes a difference - all the channels have bouquet set to auto - trying to change it by unticking auto doesn't give anything in the drop down box. I can watch channels at this point though.

Also, I can't get any EPG data - I have the OTA UK grabbers enabled. Triggering the grabber shows poll timeout \ no data erros.

Trying to start over by deleting the channels, muxes, network - it never scans the muxes successfully again - scan no data errors.

I'm running 64bit LE on a Chromebox.

Sample output from manual add of network \ muxes below. Have tried changing timout, force old etc

Any help much appreciated

Code

2017-10-14 16:46:43.193 mpegts: 10936V in Astra 28.2E - tuning on Montage Technology M88DS3103 #0 : DVB-S #0
2017-10-14 16:46:43.198 epggrab: 10936V in Astra 28.2E - registering mux for OTA EPG
2017-10-14 16:46:43.200 subscription: 00BE: "scan" subscribing to mux "10936V", we ight: 5, adapter: "Montage Technology M88DS3103 #0 : DVB-S #0", network: "Astra 28.2E", service: "Raw PID Subscription"
2017-10-14 16:46:44.213 linuxdvb: Montage Technology M88DS3103 #0 : DVB-S #0 - poll TIMEOUT
2017-10-14 16:46:44.245 linuxdvb: Montage Technology M88DS3103 #0 : DVB-S #0 - retune nodata
2017-10-14 16:46:51.873 linuxdvb: Montage Technology M88DS3103 #0 : DVB-S #0 - poll TIMEOUT
2017-10-14 16:46:52.480 linuxdvb: Montage Technology M88DS3103 #0 : DVB-S #0 - retune nodata
2017-10-14 16:46:53.193 mpegts: 10936V in Astra 28.2E - scan no data, failed

**CvH** · October 15, 2017 at 3:08 PM Official Post

Could you make some screenshots what you set at networks and at the device page?

Cryptic · October 15, 2017 at 4:20 PM

Certainly. Have tried changing settings for Force old status, Status period.

Not going to get a chance to look at this again for a while - outside work will be blocking sat dish anyway.

Thanks

Cryptic · October 15, 2017 at 4:37 PM

I should add - I had all this working under OE - then the SSD died, and went with LE for the rebuild

**CvH** · October 17, 2017 at 10:11 AM Official Post

Hmm you have disabled idle scan at the network tab,maybe this could be a problem.

Also could you pls add an pic from the network tab where I can see the status of your astra network?

Cryptic · October 18, 2017 at 7:57 PM

Will do - once the dish isn't obscured again, Thanks for looking at this.

Cryptic · November 14, 2017 at 7:49 PM

Hi,

finally, roofer done and scaffold gone.

Here's the network tab

With idle scan checked, the queue remains at 83. The muxes are being scanned, but all fail.

**CvH** · November 14, 2017 at 9:51 PM Official Post

did you pressed force scan at the pic and wait some min ?

Cryptic · November 15, 2017 at 5:25 PM

Yes. Done several scans trying the different settings on the adaptor (Input Buffer, Force old status, remove scrambled bits) to no avail.

Watched the stream and getting good signal strength whilst it's trying.

**CvH** · November 20, 2017 at 9:21 AM Official Post

You can try if LibreELEC 8.x images for additional dvb drivers improves anything.

TVHeadend issues

Similar Threads

Tvheadend 4.2 timeshifting problems

Continuity counter error

hauppauge wintv-dual hd - only see one tuner