Posts by Gregoir3

Quote from nice

Hi,

I have generated a config file for my Beelink GT1 and GT1U remote. I think the ir codes are the same with the Mini MV III II. I have mapped a few keys to use it with Libreelec. Please take a look in the beelink_gt1 file.

1. systemctl stop kodi
2. systemctl stop eventlircd
3. copy the file "beelink_gt1" to "/storage/.config/rc_keymaps/" and "rc_maps.cfg" to "/storage/.config/"
4. ir-keytable -a /storage/.config/rc_maps.cfg -s rc0
5. systemctl start eventlircd
6. systemctl start kodi

Thanks. Unfortunately "No devices found" when I run command from point 4.

Will the remote of my beelink minimx III II ever work?

Since I have a Mini MX too nothing I do seems to make my remote work.

Aah. Thanks for posting the updated IPTV Simple addon files.

Quote from Gregoir3

Oh god...😌😓. If I may be so bold..is there anywhere where I can download a compatible version of IPTV simple? thanks

I guess not then...

Oh god...😌😓. If I may be so bold..is there anywhere where I can download a compatible version of IPTV simple? thanks

Quote from kszaq

Not precisely. It is quite possible that S9xx (i.e. S905, S912 and so on) will get v4l2 in mainline kernel. For now most of S905/912 pieces are already supported in mainline, the main thing that is lacking is hardware decoding support. When this happens, we will finally be able to use mainline kernel on our devices.

What will be dropped are 8726MX, S805, S802 and S812 devices as they're very unlikely to get full mainline support.

I can't wait for that to happen. It's agonizing to see developers struggling with half supported gook or proprietary mess.

Funny problem. I wanted to reverse, yet again (because i have 2 boxes), but now the partition labeling is both STORAGE and LIBREELEC_DISK. I don't want to break anything but now I don't know what to do.

Quote from adamg

Your absolutely correct

There is absolutely no link what so ever.

So, it's either full on software decoding to play everything and get a hot device (mine starts rebooting constantly) or HW acceleration for all but some unknown files?

Quote from adamg

The problem with Netflix on Kodi is that only S/W decoding is supported, 720p should would fine.

Not every codec can be decoded by the HW decoder, I believe there are some issues with VC-1 content, I'm not sure if that was what you sent me or not as I emptied out my inbox due to being flooded with messages without looking at it properly, sorry.

I'm not sure which issue you are referring to, the addons should not be incompatible as they was recently compiled, afl1 is the resident DVB expert for S9xx so maybe he can shed some light on it.

Thanks for your reply. Maybe, just maybe since I'm not a programmer, these particular files could be excluded when using the HW accelerator so they always make use of the software decoder. But this might be a bridge to far, I don't know.

Thanks anyway.

Quote from adamg

You could check yourself and find out :p anyway it is using the same kernel as before so any issues is a hardware problem rather than a build problem.

A lot of the firmware/driver packages where rewritten in the jump from 1.0 to 1.1, I will look into this

The same files as before give the same problems. Which is; the file I sent you about a month ago and the Samantha Bee test file you also have.

If you say they will never work I will adjust my expectations.

Quote from rajawaqas

Is hardware acceleration working in adamg’s current build (1.1.2)?

Which files should work (I'm curious)? Some files still don't play or play badly with HW acceleration.

Although hardware decoding is still hit and miss, Hi10P 1080 is moving really close to actually watchable even over the network! There's setting in Settings -> System -> Sound that is blank, btw.

Quote from Eg0n_K0w@lsk1

Thanks for confirming. As the Addon works on raybuntu's Odroid build, maybe it's related to inputstream (but on the other hand SkyGo works fine.) or adamg 1.1.10.

Anyone tested netflix already with this build?

I did and it also freezes. Will go back to 1.0.8

Several add-ons are disabled because of incompatibilty with 1.0.9. Iptv simple, inputstream adaptive, and..forgot the last one.

Quote from rajawaqas

hardware acceleration is enable in player setting But LibreELEC is running in software acceleration. My box becomes heat up very soon and system is showing cpu and memory usage very high in system information while playing movie ( sorry for bad English.) My box temperature becomes 70c to 73c after half hour.

I have to agree. I have the same thing is happening to me.

EDIT:

LibreELEC:~ # modprobe amlvideodri

modprobe: FATAL: Module amlvideodri not found in directory /lib/modules/3.14.29

Very silent on this front...Any news?

Quote from kszaq

warez Technically it is possible but not easy to do and there's no step-by-step guide that one could follow. Also it would break every time you update Android.

I still like to try it.