If your box is amlogic, then I have a HowTo to set two remotes (in terms of the factory_code) to work simultaneously.
I do not have boxes beside amlogic chips so I can't test it for other boxes, but you can give it a try, no harm.
I wil try that later on.
Thanks!
Charbs
Last try:
#left_key_scancode = 0x47
#right_key_scancode = 0x15
#up_key_scancode = 0x46
#down_key_scancode = 0x16
ssarava9
Configfiles is the right place.
Keep in mind that original remote.conf from android overrides some buttons and you won't be able to map them within kodi using the keymap editor.
I don't have an airmouse to help you with 
New problem.
Have you changed both lines with 166?
key_begin
key_end
Also try to delete or block with # these ones:
ok_key_scancode = 0x55
pageup_key_scancode = 0x04
pagedown_key_scancode = 0x1b
My Nexbox A95x temperature reading is always over 140.
Any possible solution without opening the box ?
You mean Fahrenheit? It's OK then.
°F 140 = °C 60
That is very extreme!
My Tanix TX5 Pro (s905x) never heats above 60 with a small peace of metal strip.
Actually it has the best temp level among all S905x SOC boxes on the market. There's no need to glue anything else.
You have to create an advancedsettings.xml file with preffered settings and place in userdata folder. Don't forget to reboot the box.
In that link you posted for the command list it seems like I should be using 128 not 116
#define KEY_POWER 116 /* SC System Power Down */
#define KEY_STOP 128 /* AC Stop */
My mistake! Use 166 command.
Is the mouse key on all remote.conf always the fn_key_scancode ?
Also how would I have found out that global stop was 116? Is this listed somewhere?
And just curious what the # does when adding it to the front of the lines you suggested.
fn_key_scancode is usually a programmable button, it might handle some other function.
When the mouse button is pressed you can move the pointer UP/DOWN/LEFT/RIGHT by pressing the circle around OK button. And by adding # you just block unwanted lines.
116 - a standard linux command as listed there
You may also have a look at creating remote config from scratch
Charbs
It's pretty simple
fn_key_scancode = 0x17 (mouse button code 17)
left_key_scancode = 0x47
right_key_scancode = 0x15
up_key_scancode = 0x46
down_key_scancode = 0x16
ok_key_scancode = 0x55
pageup_key_scancode = 0x04
pagedown_key_scancode = 0x1bmouse_begin
# 0 0x47 (put # in front)
# 1 0x15 (put # in front)
# 2 0x46 (put # in front)
# 3 0x16 (put # in front)
mouse_endkey_begin
0x18 116
0x54 2
0x16 108
0x17 116 (replace mouse button code command with global stop 116)key_end
repeat_key_begin
0x18 116
0x54 2
0x16 108
0x17 116 (replace mouse button code command with global stop 116)
logicheart
I've been running Tanix TX5 Pro for about 3 months with different LibreELEC versions and never experienced that.
First of all try another power adapter and make sure it's connected properly.
Device: Tanix TX5Pro S905X(2GB) connected via hdmi to Samsung TV
Build: throughout 8.0.1-8.02
How to reproduce:
Play Sample1
Set contrast above or below 50 (e.g. 40) and set as default for all media
Play Sample2
Contast resets immediately, but the preset level witnin Video OSD Settings remains the same.
The problem is related to H264 HW acceleration, no bug if turned off. Also never resets on Jarvis builds.
Why needed to fix?
My LCD screen lost some brightness over time while contrast remains high(no way to change it within TV), so I lower it down in Kodi, but it gets up over and over again.
Here's mine from Tanix TX5Pro.
Tweaked to make some unused buttons work as Play/Pause, Stop, Codec Info
Attached both files - original and modified.
Enjoy 
My DVD remote generates double factory code - digits section for tv and playback section for dvd.
Is there a way to make it work with two codes in one config?
Contrast level jumps up from 46 to 50 each time i switch from live tv channel to video and back. I believe it has something to do with H264 HW acceleration. Turning it off solves the problem.
kszaq
What does this mean "improved Kodi buffering patch"?
Can I still use my own advancedsettings @150MB?
I confirm jurky playback for some mpeg2 channels and switching off mpeg2 acceleration helps to fix the problem. But not all of them related to this type of acceleration as some still get jurky upon several minutes of playback.
What interesting is that I can still play the same channels in other android applications with no issue whatsoever and all of them get hardware accelerated.
Tanix TX5Pro s905x 2GB RAM 100Mbit LAN
Just installed on Tanix TX5 Pro (s905x) and it hangs up completely when channels switch in PVR.
Should i use some advanced settings.xml to fix this?
