Maybe that is why my update from 012f to 012h went totally wrong and
destroyed my installation. :\
Same here with H version. Driver is loaded but no /dev/system
Posts by pesh
-
-
kszaq gxl_p212_1g_nand.dtb work ok. tanks!
-
kszaq I have made some tests with device trees. glx wifi work, nand not found. gxbb nand work, wifi not. With original android dtb wifi and nand are ok.
original android device tree
dtb.img - Google Drive -
-
First stock dtb from release, also gxl_p212_1g.dtb. This box is with 905x CPU and MXQ Pro case
PS. Your build with alex dtb work fine. I have to find the right dtb img. Tanks for support
-
kszaq About unrecognized NAND in s905x. I just tried AlexElec build. He use the same kernel version 3.14.29 and NAND is accesable
dmesg output
Code
Display More[ 4.244458@1] nandphy: storage 2, boot 2 [ 4.244458@1] [ 4.249548@1] nandphy: get_storage_dev return 2 [ 4.249548@1] [ 4.255661@1] nandphy: Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc. [ 4.262368@1] nandphy: ######STS IRQ mode for nand driver [ 4.267605@1] nandphy: NAND device id: 45 de 94 93 76 50 8 4 [ 4.273180@1] nandphy: detect NAND device: A serials NAND 8GiB SDTNRGAMA-008G [ 4.331081@1] nandphy: clk_reg = 81000245 [ 4.331105@1] nandphy: bus_c=6,bus_t=7,sys=5.0ns,T_REA=20,T_RHOH=25 [ 4.335666@1] nandphy: new oob mode [ 4.340351@1] nandphy: NAND CKECK:arg nbbt:arg_valid=1,blk_addr=4,page_addr=0 [ 4.352210@1] nandphy: NAND CKECK:arg ncnf:arg_valid=1,blk_addr=7,page_addr=0 [ 4.385382@1] nandphy: NAND CKECK:arg phyp:arg_valid=1,blk_addr=8,page_addr=1 [ 4.419844@1] nandphy: NAND CKECK:arg nkey:arg_valid=1,blk_addr=6,page_addr=51 [ 4.462251@1] nandphy: NAND CKECK:arg ndtb:arg_valid=1,blk_addr=9,page_addr=17 [ 4.518174@1] nandphy: NAND CKECK:arg nenv:arg_valid=1,blk_addr=10,page_addr=115 [ 4.522729@1] nandphy: nfboot : [ 4.523382@1] nandphy: off:0x000000000000-0x000001000000 :partn=0:single_chip single_plane [ 4.531584@1] nandphy: nfcache : [ 4.535025@1] nandphy: off:0x00000d000000-0x000026000000 :partn=1:single_chip multi_plane [ 4.543137@1] nandphy: nfcode : [ 4.546582@1] nandphy: off:0x000033000000-0x00007a000000 :partn=9:single_chip multi_plane [ 4.554693@1] nandphy: nfdata : [ 4.558140@1] nandphy: off:0x0000ad000000-0x000153000000 :partn=1:single_chip multi_plane -
About 906x box with unrecognized NAND issue. Here is dmesg output from android
-
I have new 905x box with android 6. It's seems the kernel do not recognize the NAND. After first boot from SD it took long time Setup Wizard to appear. Remote don't work ( i guess copy .conf from android fails ).
installtointernal output
Cannot parse config file '/etc/fw_env.config': Invalid argument
Error: environment not initialized
Backing up device tree...done.
Writing kernel image...done.
Formatting SYSTEM partition...The file /dev/system does not exist and no size was specified.
done.
Copying SYSTEM files...mount: mounting /dev/system on /tmp/system failed: No such file or directory
umount: can't unmount /tmp/system: Invalid argument
done.
Writing device tree image...done.
Formatting DATA partition...The file /dev/data does not exist and no size was specified.
done.
Restoring remote.conf...mount: mounting /dev/system on /tmp/system failed: No such file or directory
umount: can't unmount /tmp/system: Invalid argument
done. -
I posted because the similar issue was discussed here. Sorry for the offtopic
-
I have mxq pro 4k and mx905 4k. On both SD install working and both failed to boot after installtointernal. Personally I prefer LE on nand, but creating sd for nand install is too complicated for s905.
-
I think some recoveries are incompatible with sha1_check that is used in 7.0.2.5 to check if there is Android or LE/OE installed. I will revert that change for the next release. Some other minor improvements are coming developed during my work on S905 builds.
I just tried 7.0.2.007 on MXQ pro 4k. Run from SD card all good. installtointernal from ssh all OK. Reboot and black screen. Then i made SD for NAND install. Progress stop at 1/3, device reboot and start over. I am wondering if there are the same sha1_check like the last S805 image?
-
Display More
Hi kszaq,first, thank you for your effort in creating the builds for us! I have been using your OpenElec build (some old 6 version) on red stripe MXQ since around March seamlessly. Problem is, that I have decided to do an update yesterday
I took 7.0.2.5 MXQ version for update, but unfortunatelly, the update stopped, when the progress bar was in the middle, the device rebooted, then the update started again and the whole process keeped repeating.
So I have decided for a clean NAND installation, but all the 7.0.2.5 builds, that I tried (MXQ, HD18Q, m201d) behaved equally as described above.
So I did the NAND installations with all 7.0.2.4 versions. All 3 installed sucessfully, but on MXQ and m201d wifi (and bluetooth) didn't work. On HD18Q wifi and even bluetooth worked, CEC worked, but my remote didn't work. So I took remote.conf from android image and the remote started to work. I tried to turn the device off, but it just went to sleep, unlike the old openelec build I used, which turned the MXQ off. So I did a normal reboot from the menu, unfortunatelly after the reboot wifi and bluetooth stopped working.
I tried also some older openelec releases, but I don't remember the one I used and on none the wifi worked. I even installed android couple of times, where my wifi and android works and did an install of some libreelec versions after that android install, without improvement.
So the best shot was 7.0.2.4 HD18Q version, where after reboot wifi and bluetooth stopped working. Do you have any idea why? Or how to fix it? Anyway it would be also great, if turning off with remote actually turned the device off, so after turning it on, the whole system boots. I like clean start-ups. If you can give me any advice, how to have a functional build, I would be happy to try it. Otherwise I will keep looking for the openelec version I had, but I would like to have new libreelec one with kodi 16. Thanks for your help.
Same problem with NAND install on HD18Q LE 7.0.2.5 Installation start and device reboot when progress bar is at 1/3. No issues with 7.0.2.4
-
asmar tvheaded work fine
-
Can you please all try this test build for fixing playback issues Poida and njofr@ and for stability pesh: I can confirm that the board v2.0 have problems with glitchy playback, but only in 1080 videos, video playback starts ok, and after few minutes become very glitchy...when restarts playback it again starts just fine, but only for u few minutes. Videos 720 and under are always ok.
I tried all 4 nand versions and same problem.kszaq HD18Q updated from 7.0.1.4. Kodi is stable now. I can't check video playback. For some reason both kodi and LE repos don't work to download PVR client
Edit: playback is fine
-
kszaq 7.0.1.4 is working. 7.0.1.3 same issue. It's related to kernel changes for cpu you made back there i think.
-
HD18Q kodi freezes after few clicks. 7.0.2.2 NAND install. Same problem as 7.0.2.1. I managed to complete setup wizard after 3 reboots. Sometimes even network don't work. Log file attached.
-
After NAND update to 7.0.2.1 kodi freezes in 1-2 clicks. No updates on screen, no responce from the remote. I tryed Update .tar image first - same result. I had similar issue with 7.0.1.3. 7.0.1.4 was ok. Device is S805 HD18Q.