Posts by thebence

Hi Chewitt!

Both kodi.old.log and kodi.log are empty

Based on your last message "And there are other users with the same device .." I felt that you think there is some problem with my box. So we can give it up. I went back to an older FW (https://theminixforum.com/index.php?thre…-u9-h-008fw.43/) which is working mostly ok(not as good as LE does i guess ).

I wanted to try if my box boots with an older LE (eg Libreelec 8.2.2.3 as Senior Citizen wrote) but the download link in the forum ([8.2.2.3] LibreELEC 8.2 for S912) is not working. Do you have maybe a link from where i can download it?

Thanks for your help!

Hi!

Clean install is ready (same sd card, I have only one at home). I made the usual changes which you recommended earlier in post #8.

When i add textmode to the parameters than i can SSH to the box without any problem.

But when i remove the textmode than i get the:

kex_exchange_identification: read: Connection reset by peer

Could it be the problem that the first run were never completed and some settings are not ready?

When I removed "quiet" as well from the parameters, and left only ssh as additional parameter than i seen no error on the boot messages before the kodi load schreen appear. Only [ok], and some lines without any signal(as you see on the attachment).

I have a video about the boot as well if you need it

Hi!

I made the the changes in the connection as you wrote, I am using now the wifi connection.

I created the xml file as well.

I continued with a reboot command.

After boot i ran pastekodi which have not returned any URL. (I have not used ssh/putty to login just wrote pastekodi to the same promt as i started to see after I added the textmode).

1 thing which happened that the screen started to blink (sometimes 4 times a minute, sometimes once in 5 minutes) It started after I ran the commands and added the xml.

I disconnected the ethernet cable and rebooted.

To check if i am still connected i ran your commands. When i came to "services" i got no connection at all.

I tried to add both ssh and textmode as well:
ix.io/4n7w

Hi!

I downloaded the file and created a new SD.

First I tried to boot it as usual, same result - kodi splash screen.

After that I added the textmode as you wrote and booted it:

For "journalctl | paste" i got this:
ix.io/4n6T

Thank you!
I tried it and I see the libreelec device in the router ip list, but i can not ssh to it (I am using putty with port 22)

I tried the win11 ssh as well:

C:\Users\dalab>ssh 192.168.1.76

kex_exchange_identification: read: Connection reset

Connection reset by 192.168.1.76 port 22

uEnv.ini looks like this

dtb_name=/dtb/meson-gxm-minix-neo-u9h.dtb

bootargs=boot=UUID=2001-4326 disk=UUID=1f15e972-a53f-4d06-9d5f-a1195c38a657 quiet systemd.debug_shell=ttyAML0 console=ttyAML0,115200n8 console=tty0 ssh

Hello!

First of all thank you for all of you for the effort to make Minix U9-H usable again!!!!

I downloaded the LibreELEC-AMLGX.arm-10.95.0-box.img.gz and used the LibreELEC USB-SD Creator to write it to an micro sd card. I updated the uEnv.ini to the correct neo dtb.

When i start the box with "6 sec button method" than the Libreelec started to boot and the partitioning went well. After the restart i see the Libreelec logo for ca 20sec. After the Libreelec logo disappeared i see only a black screen, or the Kodi "load" screen.(I have not seen any screen like "Starting kodi the first time"). I restarted the device sometimes and always ended up with black screen or kodi load screen.

To be sure that i did everything well i re-flashed the SD again, made the uEnv.ini changes and started to boot again.

I left the box for 2 hours, and i still see the kodi loading screen so i guess it is frozen.

On the box itself i am using the following: FW001 Android 7.1.2 20191120 [Community Edition Nougat Firmware] (https://theminixforum.com/index.php?thre…-firmware.2107/)

Could you please help me with that? Should i flash the original FW to the box? Do you need any log files?(I guess i can see them if i take out the sdcard and read it on my PC).

Thanks your help in advance!!