Posts by ACDCBackInBlack

  • OutputPicture - timeout waiting for buffer

    Hello all, I have buffering issues with playing the uhd image file "goodfellas.iso" from the SMB share. See the log file below. Any hint what could be the reason for this buffering? My configuration: [raspberryPi5 openmediavault 7] <--> [raspberryPi5 libreelec 11.0.5] <--> [Samsung 4k TV]

  • Issue to add network location using SMB Protocol

    I have shared a folder called HDDtestEnv using SMB on OpenMediaVault7 (Raspberry Pi 5 PC#1). Now, I would like to add this folder to LibreELEC (Raspberry Pi 5 PC#2). Here's what I have done so far:

    On LibreELEC, I navigated to "Add network location" and entered the "Server name" and "Shared folder". Then, I clicked "OK":

    Then it prompts for "Username" and "Password," but I am unsure of what to enter. I did not set up a username and password for the shared folder HDDtestEnv on OpenMediaVault.

  • Direct communication between two Raspberries

    Hello @LybsterKodi and @chewitt,

    only for your information: I do not need any more support from your side to this topic. Everything works perfect. Thanks for your help. However, I will not leave this thread without add all my findings. May this would help also other users.

    So coming back to my Main-Question at the beginning of this thread :)

    Question:

    • What I have to do to run my 4k movies on RP2?

    Answer:

    OptionA (Direct communication or PeerToPeer)

    • ToDo:
      1. configure static IP-address of RP1
      2. configure static IP-address of RP2
    • Setup:
    • Result: PERFECT (no issues so far)
    • Performance Test:


    OptionB (communication via network switch)

    • Setup:
    • Result: ... will add my result soon
    • Performance Test: ... will add my performance tests soon

  • Direct communication between two Raspberries

    Hello @LybsterKodi,

    Quote

    1. why do you want the separate file server, what is its purpose?

    2. why not connect the SSD directly to RP2 which WILL give you the maximum speed connection?

    3. what speed is actually needed to stream 4k60Hz iso files (someone else might be able to answer this because I can't)?

    my answers:

    1. because I have also some HDDs connected to the Media-Server (RP1). I do not like the noise, the cables, the flashing lights and the HDDs itself in my living room. I prefer to bring all the stuff down to my basement room.
    2. see answer 1
    3. I checked some action scenes of the 4k Movie "The Meg, 2018" with Kodi on my Media-Player (RP2). I could measure around 80 Mbit/s. But there are other movies with around 100 Mbit/s (like the Transformers movie series)

  • Direct communication between two Raspberries

    Hello @LybsterKodi,

    thanks for help! I would choose your option 2.

    Quote

    pop a mini hub in, plug into RP1 and make the other connections through that that would allow the router to be part of the setup.

    But I am not sure if I understand you correctly. Do you mean like this: see picture below. Is this what you mean? If yes, I do not know if this would work because then both RP1 and RP2 are connected to my Router and are in the same subnet as my Router, right? But this is not what I want. i want clearly an separate system: direct communication or peer-to-peer. The reason for this is I want the maximum bitrate when I am streaming 4k60Hz iso files. I already tried it it works perfect (no buffering). But with this seperate system I an not able to access the openmediavault web interface.

  • Direct communication between two Raspberries

    Hello @chewitt,

    thanks again! I could solve it finally. I have choosen your first option:

    Quote

    a) Configure a static IPv4 address in LE settings add-on (network) settings

    Similar for openmediavault on RP1. There it was a bit complicated because I did that via the web interface while RP1 was connected to my Router. Finally, both RP1 and RP2 can communicate with each other via direct communication (peer-to-peer). I also could successfully sharing a folder with SMB on RP1 and include the shared folder into my RP2. Then, running a 4k60Hz movie with Kodi works as expected. THX!

    Here my network settings on RP1 and RP2:

    RP1: {address 192.170.1.6, netmask 255.255.255.0, gateway 192.170.1.5}

    RP2: {address 192.170.1.5, netmask 255.255.255.0, gateway 192.170.1.6}

    But, how can I change settings in openmediavault without web interface, since RP1 is not connected to my Router?

  • Direct communication between two Raspberries

    Hello @chewitt,

    thanks for your help! Before I am going through your instruction above I did the following:

    1) I checked on RP1 and RP2 which static IP address they have:

    RP1 {no IP address configured}:

    RP2 {address 192.170.1.5, netmask 255.255.255.0, gateway 192.170.1.6}:

    Do you have any idea how I can configure RP1 to have a unique static IP within the same network as RP2?

    THX and BR Marco

  • Direct communication between two Raspberries

    Hello LibreELEC-Friends,

    note that I am using in my question the acronyms RP1 and RP2 which means Raspberry Number 1 and Raspberry Number 2, respectively. Here my question: I would like to stream movies (iso files with a bit rate of around 110Mbit/s) from RP1 (this is my Media Server) to RP2 (this is my Media Player) via direct communication. All my movies are stored on a External SSD which is connected to RP1. See the picture below for a better understanding. What I have to do to run my movies on RP2?

    Thanks in advance and best regards Marco

    Edit: Why I want this setup? The first reason is i do not want all the cables, flashing lights and noises of my HDD's in my living room. Therefore I need Media-Server in the basement room and Media-Player in the living room separate. Furthermore, I guess that a direct communication (without any network switch or router in between) gives me the best performance I need.

    RP1: Raspberry Number 1, Media-Server:

    • Raspberry PI 4 B 8GB
    • openmediavault

    RP2: Raspberry Number 2, Media-Player:

    • Raspberry PI 4 B 8GB
    • LibreELEC (Matrix) 10.0.2