I dont used a PI but on both of my x86 Device i can used the analog audio normal and change simple over the settings (i testing an run without problems)
Posts by Semiotik
-
-
-
Hi,
connect via filezilla as SFT or Samba in Windows ...
rc_maps.cfg ``´´to /storage/.config
h96mp to /storage/.config/rc_keymaps
reboot ..
maybe rename the h96mp to h96mp.toml
an reboot
check in the config to and change and try
gpio-rc-recv * /storage/.config/rc_keymaps/h96mp change to
* * /storage/.config/rc_keymaps/h96mp
maybe to with the end .toml
or to last ....
https://wiki.libreelec.tv/configuration/ir-remotes
Regards
-
Try ....
take all off
dont put the hdmi cable in your NUC
1. TV on
then ....
2. Receiver on
and then
3. NUC on and put the HDMI Cable in your NUC
-
Quote
Lastly, if I bypass the receiver and plug the nuc straight to the tv it works
why you say you dont see nothing?
i'm a little confused in moment ... one times you say it works if you put the NUC directly on the TV and now you dont see nothing!
put your NUC directly on the tv and then start LE and change the settings and back to the receiver and try
-
Start the LE on you TV (there he go and you see the Dashboard)
Go under Settings in LE and then System
Change Display from Default to HDMI 0 (this what stay in your menue and the Resolution change then please from 4096xXxxx to 1920xxxx
go out and please restart one times your LE
After the Restart please check your Resolution is fixed on 1920xXXxx
then shutdown and change you NUC on the Receiverport and start the NUC again with LE
Regards and please give a feedback
-
Hi, my question is ...
install you LE on the TV / Monitor and then you change to a other room or the receiver and there you have then the issue?
Looks same my issue ofter a new installation and change the Hardware/ TV ....
If he starts at the TV please go under the Settings / System and change the option
from default to the HDMI and the max. Resolution what your receiver can used. ( i can change this settings aber a restart on the new TV but maybe you receiver or LE need with a receicer between fixed values.
-
Hi Da Flex
with the Beta 5 i make again a new install and with debug log and then i posting here in this Thread!
-
from yesterday i use the last nightly image!
-
Hi Da Flex
we dont talk from hot plug ...
- install from USB
- install some Addons
- Shut Down the Device
- unplug Power Adapter
- Change the TV
- Plugin Power Adapter
- Plugin the HDMI Cable
- Boot the Device
- LibreElec registrated the new Resolution (i see on my TV wimhich resolution he used!
Start a Movie and after 5 to 10 minutes the System Hangs
The system dont Hangs if you go after change the TV under System and accept the new resolution with Yes!
May is not issue but i change the Monitor / TV from all other Device after a shut down without Problem! I think LibreElec registration the new resolution but dont write this in the config .. so maybe the system have trouple ... I dont know .. i want inform the crew about this issue in my eyes!
-
Moin, I think I found a small bug that occurs immediately after a new installation (for me under x86)
I install LibreElec on another TV with a resolution of 1280xXX (I'm not sure if the resolution is important)
When I installed everything (I write it as it was with me) then used it and then changed the TV (connected the device to another TV) the system starts normally and you can also start add-ons and watch films The whole system hangs for about 5 minutes and no longer reacts to anything. The system can only be restarted via the power plug.
If I go to Settings after the restart - System is immediately asked Keep resolution even though nothing has been pressed, then the system sets the resolution to 1920xXX for me and everything works without problems!
But I don't have a log that happened 3 times after the reinstallation ... Reinstallation with a lower resolution, switch to a TV with a higher resolution, start film / TV - the system hangs!
The system runs stably after you have switched to the system and confirmed the immediate popup with YES!
Maybe you can check this issue!
Regards
-
-
Go in the Youtube Settings
- active one time the setup wizard
- start youtube
- Setup wizard pop up
-- Language and Region
After this the Videos play again on my 2 Device ( Maybe click on default in the youtube settings help too! )
-
Try to start the install wizard again ..
After this the videos must listen again!
Regards
-
Hello everybody!
I am a newbie with linux. Have Raspberry Pi 4 and libreelec with codi 19.1.
I need to edit the remote.xml file, but this cannot be done because: read only file system.
I ask the community to explain how I can solve this problem.
Thanks in advance
watching here: How to edit remote.xml?
-
I cannot confirm your presentation because I always make backups and import them again!
Quote
harddrive space to back it upA backup has to be stored somewhere and you also need hard disk space
Quote
20 min to back it up and another 20 to create new if neededis relative .. depends on what you have installed everything
Quote
The build in backup software just crashed or did inncomplete nonsense for me.i never had any problems
Regards
-
from the factory you don't actually have to configure anything if samba is activated, windows should list the standard directories if the protocall is set to smb 1!
that amazes me!
-
With this config i see the smb share under Windows 10!
change the settings and reboot!
after the reboot, refresh the Networkahares in windows 10!
Normaly then you must see the folder!