Dont think your motherboard supports HDR.
Posts by MatteN
-
-
Probably a powerissue.
-
I saw a major kernel change in LibreELEC-RPi4.arm-10.0-nightly-20210724-0b9677f.tar, going to aarch64. Is it including More vc4 fixes by mripard · Pull Request #4470 · raspberrypi/linux · GitHub, supposed to fix RPi4/kms: boot hangs if two monitors are connected · Issue #4465 · raspberrypi/linux · GitHub ?
I could try, but I have to admit that I'm not looking forward breaking and restoring from backup the lounge system on a Saturday evening! That would no do much good to my WAF...
Thanks!
I tried that, it wont boot, so now its a complete reinstall... and it will be a while before i try that again.
-
After an update I have the same probem.
The Wireles Regulatory Domain can be set to a specific country in the settings, but after a reboot the change is gone and "not set" again...Likewise, on several different hardware.
-
Ok, I accept this answer "partially".
But regardless, I hope I don’t have to ask again in two weeks.
And if you do, what are you going to do then, ask for a refund?
-
On my Argon ONE v2 i use the HDMI closest to the 3,5mm output, that works with CEC on my LG plasma.
-
No major issues here, running 10.0-nightly-20210611-f547d15 on both a 4GB and a 8GB
-
It seems to be Rockchip RK3066, i dont think it is supported.
-
I have several that works just fine, LG OLED65CX, LG 50" plasma and Sony 40" led.
-
Hello,
I decided to upgrade my Xtreamer Ultra 2 to run the newest version of Kodi.
Can somebody help me on what are the right steps to upgrade and what version of SW should I download?
thank you very much for the support.
Urban
Probably "Generic" as it is a Intel processor.
-
Since Kodi 19.1 has been released yesterday, will the next LE beta/rc already contain the changes since Kodi 19? If not, will the final LE 10 release be based on Kodi 19.1?
Nightlys says 19.1 after rainbowscreen on Pi 4 and versionsinfo in settings clearly states 19.1.
-
Thanks guys. I actually have no spare IR's and FLIRC dongles aren;t cheap here.. I should also have mentioned I'm in Great Britain, and the airmouse linked above is US only
Sam Nazarko and OSMC is based in UK so getting the remote i linked to in my previous post should be easy.
-
I'm using this for a couple of Pi's and a couple of Intel HTPC's.
-
Support for that skin (Aura) seems to have stopped so you will run into problems sooner or later, try something that is still supported instead.
-
Hi,
Would be curious to learn, what do you think about this little box:
Would it support H.265 in HW mode in LibreELEC? Am looking for something to replace my very old NVIDIA ION, which has served very well for 10 years, but its time has come. And, I would like something to be usable for a few years to come.
Thanks in advance, this forum is really helpful and competent.
Check for yourself:
-
Wich HDMI-port are you using, left or right?
-
Does anyone know how to overlock with the latest builds? 3B+
Edit config.txt, Config.txt - LibreELEC.wiki
Overclocking options in config.txt - Raspberry Pi Documentation
-
Armour Cae with Dual Cooling Fan
So just confirming I don't have to do anything to start them? Just powering up the Rpi with Libreelec and the the fans connected and an adequate power supply is enough?
I have a couple of similar cases, even plugged in att 3,3V they start when LibreELEC boots.
