LIRCD / Remote Problem since Updating to Version 8

Hi,

same for me, with version 7 work flawless.

I have a mac mini with an harmony.

not sure what i have to check but:

LibreELEC (official) Version: 8.0.0
Lemini:~ # ir-keytable
/sys/class/rc/: No such file or directory
Lemini:~ # cd /dev/input/
Lemini:/dev/input # ls
event0 event1 event2 event3 event4 event5 mice

so seems that LE can't see the remote interface.

But if I configure the Harmony to act as apple remote it works.

So any hint? Should i provide some logs?

I try to rollback to 7 and works, again clean install from USB to 8 (so not upgrade) and again not work... 7 again with HDD format and it works, upgrade to 8 nothing.

I downloaded the log files but i don't know what i have to share (all?)

Bus 003 Device 002: ID 05ac:8242 Apple, Inc. Built-in IR Receiver
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0         8
  idVendor           0x05ac Apple, Inc.
  idProduct          0x8242 Built-in IR Receiver
  bcdDevice            0.16
  iManufacturer           1 Apple Computer, Inc.
  iProduct                2 IR Receiver
  iSerial                 0 
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           34
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          1 Apple Computer, Inc.
    bmAttributes         0xa0
      (Bus Powered)
      Remote Wakeup
    MaxPower              100mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         3 Human Interface Device
      bInterfaceSubClass      0 
      bInterfaceProtocol      0 
      iInterface              0 
        HID Device Descriptor:
          bLength                 9
          bDescriptorType        33
          bcdHID               1.11
          bCountryCode            0 Not supported
          bNumDescriptors         1
          bDescriptorType        34 Report
          wDescriptorLength      42
         Report Descriptors: 
           ** UNAVAILABLE **
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x82  EP 2 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0008  1x 8 bytes
        bInterval              10
Device Status:     0x0000
  (Bus Powered)

Quote from P3pp3Rde

mediacenter:/dev/input # ir-keytable
Found /sys/class/rc/rc1/ (/dev/input/event13) with:
Driver em28xx, table rc-pinnacle-pctv-hd
Supported protocols: rc-5 nec rc-6
Enabled protocols: rc-5
Name: 2-5: em28178#0 IR
bus: 3, vendor/product: 2013:025f, version: 0x0001
Repeat delay = 500 ms, repeat period = 125 ms
Found /sys/class/rc/rc0/ (/dev/input/event4) with:
Driver nuvoton-cir, table rc-rc6-mce
Supported protocols: unknown other lirc rc-5 rc-5-sz jvc sony nec sanyo mce-kbd rc-6 sharp xmp
Enabled protocols: lirc
Name: Nuvoton w836x7hg Infrared Remote
bus: 25, vendor/product: 1050:00c5, version: 0x0062
Repeat delay = 500 ms, repeat period = 125 ms

mediacenter:/dev/input # ir-keytable -t -d /dev/input/event4
Testing events. Please, press CTRL-C to abort.
nothing happens when pressing keys on the remote.

dmesg:
[ 3.008765] nuvoton-cir 00:07: found NCT6779D or compatible: chip id: 0xc5 0x62
[ 3.043319] Registered IR keymap rc-rc6-mce
[ 3.043479] input: Nuvoton w836x7hg Infrared Remote Transceiver as /devices/pnp0/00:07/rc/rc0/input7
[ 3.044471] rc rc0: Nuvoton w836x7hg Infrared Remote Transceiver as /devices/pnp0/00:07/rc/rc0
[ 3.046472] snd_hda_intel 0000:00:03.0: bound 0000:00:02.0 (ops 0xffffffff81d31440)
[ 3.054433] lirc_dev: IR Remote Control driver registered, major 245
[ 3.059184] IR LIRC bridge handler initialized
[ 3.063650] rc rc0: lirc_dev: driver ir-lirc-codec (nuvoton-cir) registered at minor = 0
[ 3.063699] nuvoton-cir 00:07: driver has been successfully loaded

Display More

Could you upload the full dmesg (just do "dmesg | paste" and post the URL) and lsmod output?

Are you using userspace lirc (i.e. have you create a lircd.conf in the .config dir)? Are you running ir-keytable or other commands via http://autostart.sh/udev rules/... to setup a custom remote configuration? Which protocol/configuration are you using on your oneforall remote, is it MCE?

If you are using the nuvoton IR receiver (of your zbox) and the remote configured to (rc6) MCE protocol could you try running "ir-keytable -p rc-6 /sys/class/rc/rc0/" (double check if rc0 really is the nuvoton, it could also be rc1 since you have 2 IR receivers installed) and test if you get any events via "ir-keytable -t"?

It's quite odd that on the nuvoton IR the only enabled protocol is lirc and not lirc + rc-6. The kernel should enable the rc-6 protocol from loading the rc-rc6-mce keymap. But there's also a kernel bug, even if it enables the rc-6 protocol it didn't load the rc-6 protocol decoder - so decoding doesn't work. Manually enabling the protocol (eg via ir-keytable -p) triggers protocol decoder loading and decoding works fine again. I've already reported that bug and it was confirmed: Bug: decoders referenced in kernel rc-keymaps not loaded on boot — Linux media

so long,

Hias

Quote from P3pp3Rde

in .config there actually really is a
-rw-r--r-- 1 root root 0 Feb 2 2016 lircd.conf
but its empty.

Then better remove it

Quote

your command produced a strange output
mediacenter:~/.config # ir-keytable -p rc-6 /sys/class/rc/rc0/
ir-keytable: Too many arguments

ah, sorry, that should have been

ir-keytable -p rc-6 -s rc0

Quote

created a

/storage/.config/autostart.sh with
#!/bin/bash
# added temporarily for libreelec 8.0.0
ir-keytable -p rc-6

works. will check again with new version of libreelec.

Could you disable the autostart.sh and test if this 8.0.1 preview build works:
LibreELEC-Generic.x86_64-8.0.1.tar

so long,

Hias

@HiassofT
I have the same problem (my remote being "dead" after upgrading to 8.0)
I tried your build and there has been no change. The system still does not respond to the remote control.

I also just freshly installed 8.0 on a X86_64 platform and don't get lirc to work.

I use a lirc-server in the network and starting lirc from autostart like this helps to get irw showing me all the keypresses:
mkdir -p /var/run/lirc
/usr/sbin/lircd -c infrared-pi -O /storage/.config/lirc/lircd_options.conf /storage/.config/lirc/lircd.conf

..just kodi is not picking it up, it used to work for me like that.

Quote from nicolaberndt

I use a lirc-server in the network and starting lirc from autostart like this helps to get irw showing me all the keypresses:
mkdir -p /var/run/lirc
/usr/sbin/lircd -c infrared-pi -O /storage/.config/lirc/lircd_options.conf /storage/.config/lirc/lircd.conf

..just kodi is not picking it up, it used to work for me like that.

You also need to run lircd-uinput (adding the --uinput option of lircd might still work, but this is deprecated). See for example the lircd start script of LE:
LibreELEC.tv/lircd_helper at libreelec-8.0 · LibreELEC/LibreELEC.tv · GitHub

so long,

Hias

Thx, will try that and report back! Might not be today, but latest at the weekend I shoulkd find some time..