Hello Demetris,
I work for now on my Tronsmart MX III with the version of 26 august. I notice that after intstalling I can't start the box with the remote. I have to press the start button on the box for a while so that there will be a soft restart. I didn't had that matter in a previous version.
Tnx for your cooperation.
Fixing it for your box then is breaking it for others. Is like a loop that never ends.
Display MoreHi Demetris, I've just updated my M8C variant from 8.0.2 to 8.2rc3. all seems to update fine but up on reboot I am greeted with the following...
A start job is running for load kernel modules
which shows a timer up to4min 28s, then displays.....
Failed to start load kernel modules
See "systemctl status systemd-modules-load.service" for details
How do I view the contents of this file to share with you?
As always many thank
Paul
I wish there was a way out for you my friend but a clean install is the way forward
Hello Demetris pls. my question 1,116
How can I edit the command on this versions ( 8.2.0 RC) so that the "power button" on the remote control opens the context menu and does not sleep?
Thank you for the info
You cant, i have to do it from source then others will complain that they cant power on from remote
Maybe jotter can help you out with his kodi settings for pass-through to work reliably
jotter as i didnt exactly clear out your report can you please elaborate a bit more?
RC3 performs better or worst vs RC2?
Thanks for the feedback.
I have MXIII-G and LE 8.2 RC2 plays both DTS and Dolby Digital (when passthrough and DTS are enabled). The box is connected to the TV over HDMI, then the TV carries audio to the receiver (2001 Pioneer, supports DD/DTS) over optical. The only issue is that during the first few seconds of playing both Dolby Digital and DTS files only digital noise is produced, and then it starts working.
Can you please test RC3 if i messed anything up so i can revert my changes.
Sorry Demetris, it's the same result. Outputting @ 192khz lpcm but no recognition from the amp on what the signal is.
Thanks for the tests. Wont pursue this any more as i don't have the proper equipment to test.
Regards
Hullo. First thanks for the images! Secondly I have a mxiii+ with which I can test the HD audio codecs if you'd like?
Can you please try the latest RC2 image for your device and report back?
LibreELEC-S8X2.arm-8.2.rc2-M8.img using OpenELEC-MX3G.arm-DualBootSD zip to activate sd card boot.
Result in picture.
Thank you for trying.
I would recommend this.
1. Flash oem android firmware
2. Burn LE image to sdcard
3. Try to boot with toothpick
4. Done
Am building you a new image to test, stay tuned.
If anyone else exist that can test me HD-MA please report back with device name so i can build him/her an image too.
Ok image is ready
LibreELEC-S8X2.arm-8.2.RC3-M8S-PLUS.img.gz
Test and report.
Gracias
Avok78 On what device u r testing HD-MA? M8S+?
You are asking too much from these old boxes even S905 family has issues with 10bit HEVC
[TESTING][S905(X)] 10bit/HDR/Dithering Test Builds & Discussion
From my tests you can play any 720P 10bit HEVC without any issues, going over that and you are asking for troubles.
You can retry boot from sd from .img , all will go ok now 
Burn LibreELEC-S8X2.arm-8.0.2b-MXIII-1G.img to sdcard with etcher and boot from it then install to internal or you can try the .tar
S802/12 are able to play H265/HEVC at 4K2K = Ultra HD = 3820 x 2160 vs S905/12 that can do 4K = 4096 x 2160
And not because they are weak (they are faster that any S905 in existence) but because they use the 1.x HDMI protocol that has this limitation.
Ok! I do it by using the IP address of my computer. Thanks a lot! The only problem who is still remains is the dts sound which is not working (it's working like Dolby digital), and it's a general problem of all the 17 versions of KodiDid
Did you re-install new LE8.2-rc2?
I have, stick with AlexELEC
