Display Morediagus
Here's a Play 2 u-boot that will boot by default from sd card (unless you press the remote power button, in which case it will try to boot from eMMC, which in your case and mine, doesn't work).
Just write is to the sdcard where you have LE9 and it should work.
Just one note, the screen will be black for a few seconds on bootup in case u-boot cannot find the boot splash image in eMMC
u-boot.bin.sd.bin
Thank you very much ricopt5. It works!!! My WP2 boots LE9 form sdcard. 
chewitt, tested your img on WP2 and the ethernet works. 
[ 9.938572] meson8b-dwmac c9410000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 10.127492] meson8b-dwmac c9410000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211F Gigabit Ethernet] (irq=29)
[ 10.138801] meson8b-dwmac c9410000.ethernet eth0: No Safety Features support found
[ 10.138870] meson8b-dwmac c9410000.ethernet eth0: PTP not supported by HW
[ 10.141584] meson8b-dwmac c9410000.ethernet eth0: configuring for phy/rgmii link mode
[ 13.671718] meson8b-dwmac c9410000.ethernet eth0: Link is Up - 1Gbps/Full - flow control offdiagus Ethernet issue resolved https://github.com/chewitt/u-boot…b9285bae8061bff
I'll send some patches and an apology to the mailing list and LE master branch soon but https://chewitt.libreelec.tv/testing/LibreE…ek-play2.img.gz contains the fix.
Thanks chewitt. I will try it.
Thanks, that points fingers to somethig changing in u-boot. The question is what ??
I don't know if this can help... Below, the diffs in the console booting LE11 (left) and LE12 (right):
1c1
< =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2024.03.06 17:45:32 =~=~=~=~=~=~=~=~=~=~=~=
---
> =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2024.03.06 17:43:32 =~=~=~=~=~=~=~=~=~=~=~=
4c4
< TE: 300981
---
> TE: 563649
26c26
< 82 23 84 47 b5 54 7c 27 cb 26 69 12 [0.400291 Inits done]
---
> 82 23 84 47 b5 54 7c 27 cb 26 69 12 [0.660656 Inits done]
30c30
< Load bl33 from SD, src: 0x0003c000, des: 0x01000000, size: 0x0008eff0
---
> Load bl33 from SD, src: 0x0003c000, des: 0x01000000, size: 0x0009c550
43c43
< U-Boot 2022.10 (Jan 26 2024 - 19:01:04 +0000) wetek-play2
---
> U-Boot 2024.01 (Feb 25 2024 - 17:07:40 +0000) wetek-play2
47,49c47,49
< DRAM: 2 GiB
< Core: 164 devices, 26 uclasses, devicetree: separate
< MMC: mmc@70000: 0, mmc@72000: 1, mmc@74000: 2
---
> DRAM: 1 GiB (effective 2 GiB)
> Core: 170 devices, 28 uclasses, devicetree: separate
> MMC: mmc@70000: 2, mmc@72000: 0, mmc@74000: 1
51c51
< In: serial
---
> In: usbkbd,serial
55c55,58
< Net: eth0: ethernet@c9410000
---
> [BL31]: tee size: 0
> Net: Could not get PHY for ethernet@c9410000: addr -1
> No ethernet found.
>
58,59c61,62
< mmc1 is current device
< Scanning mmc 1:1...
---
> mmc0 is current device
> Scanning mmc 0:1...
69c72
< Data Size: 11576344 Bytes = 11 MiB
---
> Data Size: 12580402 Bytes = 12 MiB
74a78
> Working FDT set to 8008000
76c80,81
< Loading Device Tree to 000000003fff3000, end 000000003ffff639 ... OK
---
> Loading Device Tree to 000000003fff3000, end 000000003ffff638 ... OK
> Working FDT set to 3fff3000
78c83
< Starting kerne ...
---
> Starting kernel ...
80a86
> [ 0.585740] mdio_bus stmmac-0: MDIO device at address 0 is missing.The last line contains the clue .. that's the Hub u-boot binary not the WP2 one. I'll see if I can regenerate the WP2 one (needs some setup as those files were last built on some other machine).
I would appreciate if you can do it to test if could boot LE9 from SD.
Watching TV on the WP2 with LE11 and an external USB DVB stick is painful, after a few minutes the artifacts begin and tvheadend shows a lot of continuity counter errors, making it unusable.
Perhaps the best solution is to buy new hardware. 
More info, Ethernet works after updating from 11.0.6 official installed on SDcard to your testing LibreELEC-AMLGX.aarch64-11.80.0.tar.
Are you running from eMMC or SD card?
If using eMMC can you try installing a current LE11 nightly (to use an older u-boot version) and then update to a current LE12 nightly. Same problem, or does Ethernet work now?
Running both LE11 and LE12 from SD card, can't install on the eMMC of my faulty WP2 
Testing LE12.0 nightly (25-02-2024) on wetek-play2, ethernet does not work.
At boot time appears the message: ethmactool-config service failed, and dmesg shows the next messages about ethernet:
[ 1.064621] meson8b-dwmac c9410000.ethernet: IRQ eth_wake_irq not found
[ 1.064645] meson8b-dwmac c9410000.ethernet: IRQ eth_lpi not found
[ 1.064954] meson8b-dwmac c9410000.ethernet: PTP uses main clock
[ 1.066353] meson8b-dwmac c9410000.ethernet: User ID: 0x11, Synopsys ID: 0x37
[ 1.066389] meson8b-dwmac c9410000.ethernet: DWMAC1000
[ 1.066400] meson8b-dwmac c9410000.ethernet: DMA HW capability register supported
[ 1.066410] meson8b-dwmac c9410000.ethernet: RX Checksum Offload Engine supported
[ 1.066419] meson8b-dwmac c9410000.ethernet: COE Type 2
[ 1.066428] meson8b-dwmac c9410000.ethernet: TX Checksum insertion supported
[ 1.066437] meson8b-dwmac c9410000.ethernet: Wake-Up On Lan supported
[ 1.066564] meson8b-dwmac c9410000.ethernet: Normal descriptors
[ 1.066574] meson8b-dwmac c9410000.ethernet: Ring mode enabled
[ 1.066583] meson8b-dwmac c9410000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 1.066599] meson8b-dwmac c9410000.ethernet: device MAC address 8a:a1:df:bd:87:07
[ 8.862209] meson8b-dwmac c9410000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 8.863143] meson8b-dwmac c9410000.ethernet eth0: __stmmac_open: Cannot attach to PHY (error: -19)
[ 10.362672] meson8b-dwmac c9410000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 10.363531] meson8b-dwmac c9410000.ethernet eth0: __stmmac_open: Cannot attach to PHY (error: -19)With LE11 Ethernet works on the same device:
[ 1.051029] meson8b-dwmac c9410000.ethernet: IRQ eth_wake_irq not found
[ 1.051043] meson8b-dwmac c9410000.ethernet: IRQ eth_lpi not found
[ 1.051234] meson8b-dwmac c9410000.ethernet: PTP uses main clock
[ 1.052679] meson8b-dwmac c9410000.ethernet: User ID: 0x11, Synopsys ID: 0x37
[ 1.052695] meson8b-dwmac c9410000.ethernet: DWMAC1000
[ 1.052703] meson8b-dwmac c9410000.ethernet: DMA HW capability register supported
[ 1.052710] meson8b-dwmac c9410000.ethernet: RX Checksum Offload Engine supported
[ 1.052716] meson8b-dwmac c9410000.ethernet: COE Type 2
[ 1.052722] meson8b-dwmac c9410000.ethernet: TX Checksum insertion supported
[ 1.052728] meson8b-dwmac c9410000.ethernet: Wake-Up On Lan supported
[ 1.052833] meson8b-dwmac c9410000.ethernet: Normal descriptors
[ 1.052840] meson8b-dwmac c9410000.ethernet: Ring mode enabled
[ 1.052846] meson8b-dwmac c9410000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 9.020096] meson8b-dwmac c9410000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 9.209480] meson8b-dwmac c9410000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211F Gigabit Ethernet] (irq=29)
[ 9.217406] meson8b-dwmac c9410000.ethernet eth0: No Safety Features support found
[ 9.217436] meson8b-dwmac c9410000.ethernet eth0: PTP not supported by HW
[ 9.228616] meson8b-dwmac c9410000.ethernet eth0: configuring for phy/rgmii link mode
[ 12.717411] meson8b-dwmac c9410000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off¿Driver problem?
Flashed u-boot to SDcard with LE9.2.8.13.
The console output:
GXBB:BL1:08dafd:0a8993;FEAT:EDFD718C;POC:3;RCY:0;EMMC:800;NAND:81;SD:0;READ:0;CHK:0;
no sdio debug board detected
TE: 318096
BL2 Built : 09:01:42, Oct 11 2016.
gxb g88b04d6 - haixiang.bao@droid05
set vcck to 1100 mv
set vddee to 1000 mv
Board ID = 4
CPU clk: 1536MHz
DDR chl: Rank0+1 same @ 912MHz
DDR0: 1024MB(auto)-2T-13
DataBus test pass!
AddrBus test pass!
Load fip header from SD, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from SD, src: 0x00010200, des: 0x01000000, size: 0x0000d460
Sending bl30......................................................OK.
Run bl30...
Load bl31 from SD, src: 0x00020200, des: 0x101000[00, size: 0x00018190
Image: gxb_v1.1.3135-18177fc 2016-06-24 11:00:09 yun.cai@droid06]
OPS=0x13
82 23 84 47 b5 54 7c 27 cb 26 69 12 [0.414361 Inits done]
secure task start!
high task start!
low task start!
Load bl32 from SD, src: 0x0003c200, des: 0x05300000, size: 0x00035760
Load bl33 from SD, src: 0x00074200, des: 0x01000000, size: 0x000a7790
NOTICE: BL3-1: v1.0(debug):bc3419d
NOTICE: BL3-1: Built : 14:16:22, Aug 15 2016
INFO: BL3-1: Initializing runtime services
INFO: BL3-1: Initializing BL3-2
INFO: BL3-2: ATOS-V1.5-g3e467d9 #1 Mon Aug 22 17:11:43 CST 2016 arm
INFO: BL3-2: chip version = RevC (1F:C - 0:0)
INFO: BL3-2: crypto engine BLKMV
INFO: BL3-2: secure time REE
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
U-Boot 2015.01-g4c46c50-dirty (Dec 29 2019 - 07:22:01)
DRAM: 1 GiB
Relocation Offset is: 36ecb000
register usb cfg[0][1] = 0000000037f60920
register usb cfg[0][2] = 0000000037f60940
register usb cfg[2][0] = 0000000037f60960
[CANVAS]canvas init
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC: aml_priv->desc_buf = 0x0000000033ecb770
aml_priv->desc_buf = 0x0000000033ecda90
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
emmc/sd response timeout, cmd1, status=0x3ff2800
MMC init failed
Using default environment
In: serial
Out: serial
Err: serial
reboot_mode=cold_boot
hpd_state=0
cvbs performance type = 4, table = 0
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
emmc/sd response timeout, cmd1, status=0x3ff2800
mmc init failed
Amlogic multi-dtb tool
Cannot find legal dtb!
[store]Err:do_store_dtb_ops,L236:Fail in fdt check header
board_late_init(): [store dtb read $dtb_mem_addr] fail
load dtb to 1000000
[store]To run cmd[emmc dtb_read 1000000 0x40000]
read emmc dtb
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
emmc/sd response timeout, cmd1, status=0x3ff2800
mmc init failed
Amlogic multi-dtb tool
Cannot find legal dtb!
[store]Err:do_store_dtb_ops,L236:Fail in fdt check header
board_late_init(): store dtb read 1000000 fail
ret = 1 .[mmc_init] mmc init success
Device: SDIO Port B
Manufacturer ID: 3
OEM: 5344
Name: SC32G
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 29.7 GiB
mmc clock: 40000000
Bus Width: 4-bit
Net: Phy 0 not found
dwmac.c9410000
iubootVersion = 1,pubootVersion = 1
uboot version is not the same, need to do defenv
## defenv_reserve
Saving Environment to aml-storage...
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
emmc/sd response timeout, cmd1, status=0x3ff2800
MMC init failed
wipe_data=successful
wipe_cache=successful
upgrade_step=0
## Error: "bootmode_check" not defined
Device: SDIO Port B
Manufacturer ID: 3
OEM: 5344
Name: SC32G
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 29.7 GiB
mmc clock: 40000000
Bus Width: 4-bit
reading kernel.img
10379264 bytes read in 570 ms (17.4 MiB/s)
[OSD]check dts: FDT_ERR_BADMAGIC, load default fb_addr parameters
[OSD]fb_addr for logo: 0x3d800000
[OSD]check dts: FDT_ERR_BADMAGIC, load default fb_addr parameters
[OSD]fb_addr for logo: 0x3d800000
[CANVAS]addr=0x3d800000 width=3840, height=2160
Cannot find dev.
amlmmc cmd <NULL> failed
store - STORE sub-system
Usage:
store store init flag
store read name addr off|partition size
read 'size' bytes starting at offset 'off'
to/from memory address 'addr', skipping bad blocks.
store write name addr off|partition size
write 'size' bytes starting at offset 'off'
to/from memory address 'addr', skipping bad blocks.
store rom_write add off size.
write uboot to the boot device
store erase boot/data:
erase the area which is uboot or data
store erase partition <partition_name>:
erase the area which partition in u-boot
store erase dtb
store erase key
store disprotect key
store rom_protect on/off
store scrub off|partition size
scrub the area from offset and size
store dtb iread/read/write addr <size>
read/write dtb, size is optional
store key read/write addr <size>
read/write key, size is optional
cmd store failed
Err imgread(L333):Fail to read 0x2000B from part[logo] at offset 0
There is no valid bmp file at the given address
[KM]Error:f[keymanage_dts_parse]L282:not a fdt at 0x0000000001000000
gpio: pin GPIOAO_3 (gpio 122) value is 1
get_cpu_id flag_12bit=0
saradc - saradc sub-system
Usage:
saradc saradc open <channel> - open a SARADC channel
saradc close - close the SARADC
saradc getval - get the value in current channel
saradc get_in_range <min> <max> - return 0 if current value in the range of current channel
get_rebootmode = cold_boot
InUsbBurn
noSof
Device: SDIO Port B
Manufacturer ID: 3
OEM: 5344
Name: SC32G
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 29.7 GiB
mmc clock: 40000000
Bus Width: 4-bit
reading kernel.img
10379264 bytes read in 570 ms (17.4 MiB/s)
key1 = ef18877
key2 = ef18877
time_out = 4c4b40
ir init
irkey - irkey key_value1 key_value2 time_value
Usage:
irkey
no_power_key_press
Hit any key to stop autoboot: 1 0
reading boot.ini
** Unable to read file boot.ini **
cfgload: no boot.ini or empty file
Cannot find dev.
amlmmc cmd <NULL> failed
store - STORE sub-system
Usage:
store store init flag
store read name addr off|partition size
read 'size' bytes starting at offset 'off'
to/from memory address 'addr', skipping bad blocks.
store write name addr off|partition size
write 'size' bytes starting at offset 'off'
to/from memory address 'addr', skipping bad blocks.
store rom_write add off size.
write uboot to the boot device
store erase boot/data:
erase the area which is uboot or data
store erase partition <partition_name>:
erase the area which partition in u-boot
store erase dtb
store erase key
store disprotect key
store rom_protect on/off
store scrub off|partition size
scrub the area from offset and size
store dtb iread/read/write addr <size>
read/write dtb, size is optional
store key read/write addr <size>
read/write key, size is optional
cmd store failed
Err imgread(L132):Fail to read 0x100000B from part[boot] at offset 0
InUsbBurn
noSof
Device: SDIO Port B
Manufacturer ID: 3
OEM: 5344
Name: SC32G
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 29.7 GiB
mmc clock: 40000000
Bus Width: 4-bit
Device: SDIO Port B
Manufacturer ID: 3
OEM: 5344
Name: SC32G
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 29.7 GiB
mmc clock: 40000000
Bus Width: 4-bit
reading aml_autoscript
** Unable to read file aml_autoscript **
reading recovery.img
** Unable to read file recovery.img **
(Re)start USB...
USB0: dwc_usb driver version: 2.94 6-June-2012
USB (0) peri reg base: c0000000
USB (0) use clock source: XTAL input, div: 1
USB (0) base addr: 0xc9000000
Force id mode: Host
dwc_otg: No USB device found !
lowlevel init failed
USB1: dwc_usb driver version: 2.94 6-June-2012
USB (1) peri reg base: c0000020
USB (1) use clock source: XTAL input, div: 1
USB (1) base addr: 0xc9100000
Force id mode: Host
dwc_otg: Highspeed device found !
scanning bus 1 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
** Bad device usb 0 **
Cannot find dev.
amlmmc cmd <NULL> failed
store - STORE sub-system
Usage:
store store init flag
store read name addr off|partition size
read 'size' bytes starting at offset 'off'
to/from memory address 'addr', skipping bad blocks.
store write name addr off|partition size
write 'size' bytes starting at offset 'off'
to/from memory address 'addr', skipping bad blocks.
store rom_write add off size.
write uboot to the boot device
store erase boot/data:
erase the area which is uboot or data
store erase partition <partition_name>:
erase the area which partition in u-boot
store erase dtb
store erase key
store disprotect key
store rom_protect on/off
store scrub off|partition size
scrub the area from offset and size
store dtb iread/read/write addr <size>
read/write dtb, size is optional
store key read/write addr <size>
read/write key, size is optional
cmd store failed
Err imgread(L132):Fail to read 0x100000B from part[recovery] at offset 0
wetek_hub#No surprises chewitt, tested following the instructions with no success: Bad Linux ARM64 Image magic!
This is the console output (lines about PHY for ethernet removed):
GXBB:BL1:08dafd:0a8993;FEAT:EDFD718C;POC:3;RCY:0;EMMC:800;NAND:81;SD:0;READ:0;CHK:0;
no sdio debug board detected
TE: 1208891
BL2 Built : 09:01:42, Oct 11 2016.
gxb g88b04d6 - haixiang.bao@droid05
set vcck to 1100 mv
set vddee to 1000 mv
Board ID = 4
CPU clk: 1536MHz
DDR chl: Rank0+1 diff @ 912MHz
DDR0: 1024MB(auto)-2T-13
DDR1: 1024MB(auto)-2T-13
DataBus test pass!
AddrBus test pass!
Load fip header from SD, src: 0x0000c000, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from SD, src: 0x00010000, des: 0x01000000, size: 0x0000d460
Sending bl30......................................................OK.
Run bl30...
Load bl31 from SD, src: 0x00020000, des: 0x101000[0, size: 0x00018190
Image: gxb_v1.1.3135-18177fc 2016-06-24 11:00:09 yun.cai@droid06]
OPS=0x13
82 23 84 47 b5 54 7c 27 cb 26 69 12 [1.307718 Inits done]
secure task start!
high task start!
low task start!
Load bl33 from SD, src: 0x0003c000, des: 0x01000000, size: 0x0009c550
NOTICE: BL3-1: v1.0(debug):bc3419d
NOTICE: BL3-1: Built : 14:16:22, Aug 15 2016
INFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
<debug_uart>
U-Boot 2024.01 (Feb 24 2024 - 15:14:17 +0000) wetek-play2
Model: WeTek Play 2
SoC: Amlogic Meson GXBB (S905) Revision 1f:c (13:1)
DRAM: 1 GiB (effective 2 GiB)
Core: 170 devices, 28 uclasses, devicetree: separate
MMC: mmc@70000: 2, mmc@72000: 0, mmc@74000: 1
Loading Environment from nowhere... OK
In: usbkbd,serial
Out: serial
Err: serial
[BL31]: tee size: 0
[BL31]: tee size: 0
Net:
No ethernet found.
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
1: LibreELEC
Retrieving file: /KERNEL
append: boot=LABEL=LIBREELEC disk=LABEL=STORAGE quiet systemd.debug_shell=ttyAML0 console=ttyAML0,115200n8 console=tty0
Retrieving file: /meson-gxbb-wetek-play2.dtb
Bad Linux ARM64 Image magic!
EXTLINUX FAILED: continuing...
Card did not respond to voltage select! : -110
starting USB...
Bus usb@c9000000: USB DWC2
Bus usb@c9100000: USB DWC2
scanning bus usb@c9000000 for devices... 1 USB Device(s) found
scanning bus usb@c9100000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Device 0: unknown device
Could not get PHY for ethernet@c9410000: addr -1
...
No ethernet found.
missing environment variable: pxeuuid
Retrieving file: /extlinux/pxelinux.cfg/00000000
No ethernet found.
Retrieving file: /extlinux/pxelinux.cfg/0000000
No ethernet found.
Retrieving file: /extlinux/pxelinux.cfg/000000
No ethernet found.
Retrieving file: /extlinux/pxelinux.cfg/00000
No ethernet found.
Retrieving file: /extlinux/pxelinux.cfg/0000
No ethernet found.
Retrieving file: /extlinux/pxelinux.cfg/000
No ethernet found.
Retrieving file: /extlinux/pxelinux.cfg/00
No ethernet found.
Retrieving file: /extlinux/pxelinux.cfg/0
No ethernet found.
Retrieving file: /extlinux/pxelinux.cfg/default-arm-meson-p200
No ethernet found.
Retrieving file: /extlinux/pxelinux.cfg/default-arm-meson
No ethernet found.
Retrieving file: /extlinux/pxelinux.cfg/default-arm
No ethernet found.
Retrieving file: /extlinux/pxelinux.cfg/default
No ethernet found.
Config file not found
No ethernet found.
=>Thanks chewitt.
I have tried both options with the same result: no boot from sdcard
Attached the serial cable, console shows a boot loop:
GXBB:BL1:08dafd:0a8993;FEAT:EDFD718C;POC:3;RCY:0;EMMC:800;NAND:81;SD:0;READ:0;CHK:F3;USB:8;LOOP:1;EMMC:800;NAND:81;SD:0;READ:0;CHK:F3;USB:8;LOOP:2;EMMC:800;NAND:81;SD:0;READ:0;CHK:F3;USB:8;LOOP:3;EMMC:800;NAND:81;SD:0;READ:0;CHK:F3;USB:8;LOOP:4;EMMC:800;NAND:81;SD:0;READ:0;CHK:F3;USB:8;LOOP:5;EMMC:800;NAND:81;SD:0;READ:0;CHK:F3;USB:8;LOOP:6;EMMC:800;NAND:81;SD:0;READ:0;CHK:F3;USB:8;I also tried flashing your testing u-boot on sdcard (https://chewitt.libreelec.tv/testing/u-boot…bin-wetek-play2). The system boots, detect the USB but can't boot de LE 9.2.8, as expected.
GXBB:BL1:08dafd:0a8993;FEAT:EDFD718C;POC:3;RCY:0;EMMC:800;NAND:81;SD:0;READ:0;CHK:0;
no sdio debug board detected
TE: 437761
BL2 Built : 09:01:42, Oct 11 2016.
gxb g88b04d6 - haixiang.bao@droid05
set vcck to 1100 mv
set vddee to 1000 mv
Board ID = 4
CPU clk: 1536MHz
DDR chl: Rank0+1 diff @ 912MHz
DDR0: 1024MB(auto)-2T-13
DDR1: 1024MB(auto)-2T-13
DataBus test pass!
AddrBus test pass!
Load fip header from SD, src: 0x0000c000, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from SD, src: 0x00010000, des: 0x01000000, size: 0x0000d460
Sending bl30......................................................OK.
Run bl30...
Load bl31 from SD, src: 0x00020000, des: 0x101000[00, size: 0x00018190
Image: gxb_v1.1.3135-18177fc 2016-06-24 11:00:09 yun.cai@droid06]
OPS=0x13
82 23 84 47 b5 54 7c 27 cb 26 69 12 [0.536598 Inits done]
secure task start!
high task start!
low task start!
Load bl33 from SD, src: 0x0003c000, des: 0x01000000, size: 0x0008f7a0
NOTICE: BL3-1: v1.0(debug):bc3419d
NOTICE: BL3-1: Built : 14:16:22, Aug 15 2016
INFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
<debug_uart>
U-Boot 2023.10 (Nov 25 2023 - 16:55:39 +0000) wetek-play2
Model: WeTek Play 2
SoC: Amlogic Meson GXBB (S905) Revision 1f:c (13:1)
DRAM: 1 GiB (effective 2 GiB)
Core: 163 devices, 26 uclasses, devicetree: separate
MMC: mmc@70000: 2, mmc@72000: 0, mmc@74000: 1
Loading Environment from nowhere... OK
In: usbkbd,serial
Out: serial
Err: serial
[BL31]: tee size: 0
[BL31]: tee size: 0
Net: Could not get PHY for ethernet@c9410000: addr -1
No ethernet found.
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Card did not respond to voltage select! : -110
starting USB...
Bus usb@c9000000: USB DWC2
Bus usb@c9100000: USB DWC2
scanning bus usb@c9000000 for devices... 2 USB Device(s) found
scanning bus usb@c9100000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Device 0: Vendor: SanDisk Rev: 1.00 Prod: Cruzer Snap
Type: Removable Hard Disk
Capacity: 29340.0 MB = 28.6 GB (60088320 x 512)
... is now current device
Scanning usb 0:1...
Could not get PHY for ethernet@c9410000: addr -1
Could not get PHY for ethernet@c9410000: addr -1
Could not get PHY for ethernet@c9410000: addr -1
...Hi all.
I was using a Wetek Play 2 with internal tuner with the dtech LE 9.2.8 image installed on the emmc but it suddenly stopped booting. I think it is a hardware failure of the emmc chip.
I have tried booting from the SD card with different LE9 images with no success.
Booting from SD card with LE11 and L12 nighly images works but I can't use the internal tuner.
Is there a way to boot LE9 on WP2 from the SD card without a working emmc?
Thanks in advance.