I do again the tests in a clean instalation of 9.2.8.13:
- Without my remote.conf. The remote control does not work. no one key works.
- With my remote.conf only works the 4 directions keys.
- With MXIII-G Remote works the more important keys, all that I need.
Thank you very much!
Okay, this is actually a config of two different remotes integrated into one file. Well, not exactly the best solution. But one of these codes is also included in the image by default since v9.2.8.12 (0xff000001).
Question:
Does the remote control work even without your custom config?If the answer is no, then the other one will be, then try this: MXIII-G Remote (0x7f800001)
(Of course, there is no guarantee that all buttons will work.)
Thank you!
The remote doesn't work (only direction keys) with or without the custom config. Is like the reomte.conf does not anything.
The MXIII-G Remote works fort me (directions, back, ok, and power).
Could you send me this remote.conf?
Here is the remote.conf:
#*********************************************************************************************************
#this file is configuration for each factory remote device
# work_mode 0 :software mode 1 :hardware mode
# repeat_enable 0 :disable repeat 1 :enable repeat
#
# factory_code each device has it's unique factory code.
# pattern:custom_code(16bit)+index_code(16bit)
# examble: 0xff000001 = 0xff00(custom cod) 0001 (index)
#
# release_delay unit:ms.release will report from kernel to user layer after this period of time
# from press or repeat triggered.
#
# debug_enable 0 :debug disable 1 :debug disable
#
# SW MODE:
# bit_count how many bits in each frame
# tw_leader_act time window for leader active
# tw_bit0 time window for bit0 time.
# tw_bit1 time window for bit1 time
# tw_repeat_leader time window for repeat leader
# REG
# reg_base_gen set value for PREG_IR_DEC_BASE_GEN
# reg_control set value for PREG_IR_DEC_CONTROL
# reg_leader_act set value for PREG_IR_DEC_LEADER_ACTIVE
# reg_leader_idle set value for PREG_IR_DEC_LEADER_IDLE
# reg_repeat_leader set value for PREG_IR_DEC_REPEAT_IDLE
# reg_bit0_time set value for PREG_IR_DEC_BIT0_TIME
#*************************************************************************************************************
#amlogic NEC remote
work_mode = 0
repeat_enable = 1
repeat_delay = 130
repeat_peroid = 120
release_delay = 20
debug_enable = 1
#fn_key_scancode = 0x15
#left_key_scancode = 0x1c
#right_key_scancode = 0x48
#up_key_scancode = 0x44
#down_key_scancode = 0x1d
#ok_key_scancode = 0x5c
#pageup_key_scancode = 0x04
#pagedown_key_scancode = 0x1b
custom_begin
factory_infcode = 0
factory_code = 0xff000001
fn_key_scancode = 0x5c
left_key_scancode = 0x0e
right_key_scancode = 0x1a
up_key_scancode = 0x03
down_key_scancode = 0x02
ok_key_scancode = 0x07
mouse_begin
0 0x0e
1 0x1a
2 0x03
3 0x02
mouse_end
key_begin
0x14 704
0x48 102
0x5c 63
0x03 103
0x02 108
0x0e 105
0x1a 106
0x07 97
0x13 139
0x01 158
0x58 114
0x0b 115
key_end
repeat_key_begin
0x14 704
0x48 102
0x5c 63
0x03 103
0x02 108
0x0e 105
0x1a 106
0x07 97
0x13 139
0x01 158
0x58 114
0x0b 115
repeat_key_end
custom_end
custom_begin
factory_infcode = 1
factory_code = 0x7f800001
fn_key_scancode = 0x52
left_key_scancode = 0x25
right_key_scancode = 0x27
up_key_scancode = 0x26
down_key_scancode = 0x28
ok_key_scancode = 0x0d
mouse_begin
0 0x25
1 0x27
2 0x26
3 0x28
mouse_end
key_begin
0x4d 113
0x56 114
0x4e 115
0x25 105
0x26 103
0x27 106
0x28 108
0x0d 97
0x1b 158
0x53 102
0x51 704
0x49 139
0x52 63
0x31 2
0x32 3
0x33 4
0x34 5
0x35 6
0x36 7
0x37 8
0x38 9
0x39 10
0x30 11
0x58 288
0x44 14
0xbd 122
0xbb 123
0x09 292
0x11 289
0x54 290
0x4f 291
0xbc 140
0x40 67
0x41 177
0x42 178
key_end
repeat_key_begin
0x4d 113
0x56 114
0x4e 115
0x25 105
0x26 103
0x27 106
0x28 108
0x0d 97
0x1b 158
0x53 102
0x51 704
0x49 139
0x52 63
0x31 2
0x32 3
0x33 4
0x34 5
0x35 6
0x36 7
0x37 8
0x38 9
0x39 10
0x30 11
0x58 288
0x44 14
0xbd 122
0xbb 123
0x09 292
0x11 289
0x54 290
0x4f 291
0xbc 140
0x40 67
0x41 177
0x42 178
repeat_key_end
custom_endThank you!
Hello!
I have a Beelink GT1 Ultimate. I have instaled yesterday Libreelec 9.2.8. Everything that i test works well, but the remote control. I tried to put my remote.conf (that works in other versions of Libre an Core) in storage/.config but does not work in this one. I have tried to install in 9.2.8.9 and 9.2.8.13.
In both cases, only works cursor keys (up, down, left and right) and volume keys. The ok and the power key don´'t work.
Thanks in advise.