Posts by jordixPI3

ok thank you again, is not just plugging the fan then.

thanks

hello, thanks a lot, i will install it this afternoon (Opi3 lts).

thanks a gain

editing: installed your last message zip orange tools file, installed service fan zip addon, but im not sure what to do in addon settings, LTS model is no present so i choose opi3 board, fan negative to pin 6, fan positive to pin? i tried set to pins 8, 10, 12, 3 and some others with no success, what am i doing wrong?

i dont want to bother you, im not an expert with electronics so, if you think you dont have to lose your time its ok, fan sound is not really a big problem for me unless some times when alone st night and tv volume very low.

thank again

hi there, im a bit confused, will it actully works with LE12+ h6, or the only LE12 option is h3 so far?

thank you

hi there, dont know if this coud help, i coud swear its since v12... sometimes i had that same issue, is unsual to happend, just very little times, but when it happends is after rebboting machine (OPi3 LTS), screens stars with 1024x768 and 4:3 format, then i have to shut OPi down, turn TV off, then TV on, then boot OPi3 and back to"normal" resolution (1080p 16:9), however i always thought this was because of my very old TV set (about 16 years old).

regards.

Quote from chewitt

If it's not causing an issue, ignore it.

no is not (as i said before), i just posted it for you in case of interest, nothing else.

yes they are there, the only different is that errors messages dissapear from screen much faster, reboot is faster and you can barely see that screeen, but yes, i took a photo and same errors shown.

btw, when shutting down, the errors shown are only 1st and 2nd lines, 3rd error line is not present

hello.

https://paste.libreelec.tv/relaxed-liger.log

I tried a fresh install (SD) for testing, same error happend

hello. i see that when rebooting system. is that normal?

to be honest im not sure if that was happening since latest 12.0.1 was installed, however everthing works fine, no issues so far.

Orange pi3 lts, no SD installed (emmc intallarion using ssh install2emmc command), 1 HDD and 1 SSD attached to USB ports.

Quote from jbinkley60

Thank you so much for LibrELEC 12.0.1 which has Kodi 12.1 and has the fix for the stereo upmix issue. I can confirm that I have my left front speaker back now when using stereo upmix with 2ch audio sources on an N100 box.

Jeff

hello i have noticed that with same config as previous release (no changes in the sound settings, that is, 2.0 channels,) my center speaker volume its quite higher, no problem on that, just lowering it to the desired level.

hello, and rock 64 does not come with emmc chip, i like emmc thing, so i think i will keep my orenge pi 3 lts for longer...

just asking about it

what a bout pine 64 rock 64?, sorry to keep this thread but i think its better then open new one.

thank you

arrgh, didnt realized on that, big negative point for s905x3 then, i dont run more than 1080p because of my old tv, however that would be step back from my allwinner h6 that has has hw decodig if needed...

thank you for your reply, ill keep searching

hello, im actually running LE on orange pi 3 lts, no complaints on it, but i im sure it runs with RAM lack (2Gb), so im thinking about to test banana pi m5 because i saw there is a LE version for it and thios device have 4gb RAM, so my questions are:

is there anyone running LE 12 on this device sucessfully?

and important question: does it allow intall2emmc?

thank you

hello, thanks a lot. so far running fine on orange pi 3 lts

cheers.

yes, it seems to be overlays issue

hi there, the issue seems to be something about subtitles i will explain it: if movie need subs in some pars, subs are on by default, screen flickers, but if subs are not required (some other parts of the movie in my mother language i.e.) subs stops, its ok, but still enabled, just setting them to none, flicker stops.

hello, im having same issue since a couple of days ago, but not always (so maybe problem there before and i didnt see it before), it happends suddenly, some times video "break" images when OSD is up and dissapear when OSD is gone, others is just the contrary, video starts to show "broken" images, bands, jumps, flashes that stops when OSD is opened.

just stopping playback and starting again problem dissapear, have to say that for me, setting to EGL does make no difference

hardaware is orange pi3 lts, install is 12.0 "jernej ethernet patch"