freenix I just tested latest LE master image on my OrangePi Win on a freshly unpacked SD card and it still works fine for me.
At this point it would be useful to get Kodi log and output of dmesg command. You can do that either over ssh or serial terminal. Ssh is easier, if you don't have it already enabled, just append ssh at the end of APPEND line in extlinux config on SD card. If that doesn't work, you'll have to connect serial dongle to the board and enable it in extlinux conf by modifying APPEND line - switch console parameters around and append systemd.debug-shell=1 at the end. In either case, please provide output of dmesg command and content of .kodi/temp/kodi.log
LibreELEC-A64.arm-9.80-devel-20200805221609-bd5130b-orangepi-win.img.gz
U-Boot SPL 2020.04 (Aug 05 2020 - 19:54:16 +0200)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE: BL31: v2.2(release):9.0.0-3780-geabee4a8a97c-dirty
NOTICE: BL31: Built : 21:12:59, Aug 4 2020
NOTICE: BL31: Detected Allwinner A64/H64/R18 SoC (1689)
NOTICE: BL31: Found U-Boot DTB at 0x40800e0, model: OrangePi Win/Win Plus
NOTICE: BL31: PMIC: Detected AXP803 on RSB.
U-Boot 2020.04 (Aug 05 2020 - 19:54:16 +0200) Allwinner Technology
CPU: Allwinner A64 (SUN50I)
Model: OrangePi Win/Win Plus
DRAM: 2 GiB
MMC: mmc@1c0f000: 0, mmc@1c10000: 1
Loading Environment from FAT... *** Warning - bad CRC, using default environment
In: serial@1c28000
Out: serial@1c28000
Err: serial@1c28000
Net: No ethernet found.
starting USB...
No working controllers found
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
183 bytes read in 5 ms (35.2 KiB/s)
1: LibreELEC
Retrieving file: /KERNEL
21524488 bytes read in 1128 ms (18.2 MiB/s)
append: boot=UUID=0508-1625 disk=UUID=084266b3-ef42-4473-85a7-fbf6d8269ca8 quiet console=ttyS0,115200 console=tty1 systemd.debug-shell=1
Retrieving file: /sun50i-a64-orangepi-win.dtb
30039 bytes read in 5 ms (5.7 MiB/s)
## Flattened Device Tree blob at 4fa00000
Booting using the fdt blob at 0x4fa00000
Loading Device Tree to 0000000049ff5000, end 0000000049fff556 ... OK
Starting kernel ...
[ 0.198532] sun50i-de2-bus 1000000.bus: Error couldn't map SRAM to device
[ 0.199304] sun4i-usb-phy 1c19400.phy: Couldn't request ID GPIO
[ 0.395076] sun8i-dw-hdmi 1ee0000.hdmi: Couldn't get regulator
[ 0.395586] sun4i-drm display-engine: Couldn't bind all pipelines components
[ 0.410605] sun4i-usb-phy 1c19400.phy: Couldn't request ID GPIO
and it's all from the console.......................
LibreELEC-A64.arm-9.80-nightly-20200808-63dfb3b-orangepi-win.img.gz
replaced file
system booted
these are logs