Dear everyone
I have a TV box is sumavision Q7 , CPU: Amlogic S905L, Does anybody let it use LibreELEC,
upload my dtb and init log
thanks
------------------------------------------------------------------------------------------------------------------------------
init log
------------------------------------------------------------------------------------------------------------------------------
TE: 24611
BL2 Built : 17:04:12, Jun 21 2016.
gxl g21e86b3 - yao.zhang@droid07
set vcck to 1080 mv
set vddee to 1050 mv
Board ID = 8
CPU clk: 1200MHz
DDR chl: Rank0+1 @ 720MHz - FAIL
DDR chl: Rank0 @ 720MHz - PASS
DQS-corr enabled
DDR scramble enabled
Rank0: 1024MB(auto)-2T-11
DataBus test pass!
AddrBus test pass!
NAND init
Load fip header from NAND, src: 0x0000c000, des: 0x01400000, size: 0x00004000
Load bl30 from NAND, src: 0x00010000, des: 0x01100000, size: 0x00007400
Load bl301 from NAND, src: 0x00018000, des: 0x01200000, size: 0x00002200
Load bl31 from NAND, src: 0x0001c000, des: 0x10100000, size: 0x00015400
Load bl33 from NAND, src: 0x00034000, des: 0x01000000, size: 0x000a4c00
NOTICE: BL3-1: v1.0(debug):bbbdfd9
NOTICE: BL3-1: Built : 11:52:23, May 10 2016
aml log : bl31 normal boot !
[Image: gxl_v1.1.3084-a43a30d 2016-08-09 10:27:20 yun.cai@droid06]
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: 0 0 3 c c 0 51 b4 40 a0 0 c4 not ES chip
efuse init ops = c4
efuse init hdcp = c, cf9=7
[0.375417 Inits done]
secuINFrOe: t a s kB Ls3t-a1r:t !In
itializing rhuingthi mtea sskervices
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
U-Boot 2015.01-svn138195 (Jan 02 2018 - 01:05:48)
DRAM: 1 GiB
Relocation Offset is: 36ed0000
gpio: pin GPIODV_24 (gpio 43) value is 0
gpio: pin GPIOAO_3 (gpio 103) value is 1
register usb cfg[0][1] = 0000000037f63728
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
NAND device id: 2c 64 44 4b a9 0 0 0
detect NAND device: B revision NAND 8GiB MT29F64G08CBABA
new oob mode
bus_c=6,bus_t=7,sys=4.0ns,T_REA=16,T_RHOH=15
show_phydev_list
0: nfboot
detect new nand here and new_type:50
NAND CKECK:arg nbbt: valid=1, blk=5, page=0
NAND CKECK:arg fbbt: valid=1, blk=6, page=0
outside dtb: 0000000000000000
using dtb on nand
amlnf_dtb_init_partitions: probe.
NAND CKECK:arg ndtb: valid=1, blk=9, page=66
NAND CKECK:arg ncnf: valid=1, blk=7, page=0
aml_key_init probe.
NAND CKECK:arg nkey: valid=1, blk=10, page=0
boot_device_flag 1
NAND CKECK:arg nenv: valid=1, blk=4, page=45
nfboot : 0x000000000000-0x000000800000 :partn=0:single_chip single_plane
nfcache : 0x000006800000-0x000029000000 :partn=2:single_chip multi_plane
nfcode : 0x00002f800000-0x00005c800000 :partn=9:single_chip multi_plane
nfdata : 0x00008c000000-0x000174000000 :partn=3:single_chip multi_plane
(nfboot) bad blks 0
(nfcache) bad blks 0
(nfcode) bad blks 0
(nfdata) bad blks 0
amlnf_logic_init() start
(nfcache), size:29000000
nftl version 1.01.001
size_in_blk 164; total_block 163;
nftl start: size 163, free 19
-blks(163), total_blocks(144)
(nfcode), size:5c800000
nftl version 1.01.001
nftl start: size 370, free 38
-blks(370), total_blocks(332)
amlnf_logic_init() done
MMC: aml_priv->desc_buf = 0x00000000340a8790
aml_priv->desc_buf = 0x00000000340aa7a0
SDIO Port B: 0, SDIO Port C: 1
uboot env amlnf_env_read : ####
In: serial
Out: serial
Err: serial
board id is : 8
reboot_mode=cold_boot
hpd_state=0
cvbs performance type = 7, table = 1
[store]To run cmd[amlnf dtb_read 0x1000000 0x40000]
cmd dtb_read:
amlnf_dtb_read: ####
262144 bytes dtd_read : OK
dwmac.c9410000
Error: dwmac.c9410000 address not set.
wipe_data=successful
wipe_cache=successful
upgrade_step=2
reboot_mode=cold_boot
[CANVAS]addr=0x3d800000 width=5760, height=2160
-------------mac=9C:62:AB:7D:59:53-----------------
IR init done!
gpio: pin GPIOH_6 (gpio 55) value is 1
Hit any key to stop autoboot: 0
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =340d2c90
copy done
Single dtb detected
load dtb from 0x1000000 ......
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x02013090
Loading Ramdisk to 33c36000, end 33ebd9bc ... OK
Loading Device Tree to 000000001fff4000, end 000000001ffffdbb ... OK
Starting kernel ...
uboot time: 2973975 us
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.14.29-svn145751 (root@ubuntu) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1 SMP PREEMPT Tue Jan 2 01:43:33 PST 2018
[ 0.000000@0] CPU: armv71 Processor [410fd034] revision 4
[ 0.000000@0] bootconsole [earlycon0] enabled
[ 0.180463@0] tv_vout: [tvout_get_of_data] failed to get ext_switch_pin!
[ 0.675960@3] amlogic-new-usb3 d0078080.usb3phy: This phy has no usb port
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0
[ 0.848168@3] aml_sysled_dt_parse: faild to get active_low
[ 1.248915@3] aml_snd_m8_card aml_m8_snd.48: ASoC: no source widget found for LOUTL
[ 1.250910@3] aml_snd_m8_card aml_m8_snd.48: ASoC: Failed to add route LOUTL -> direct -> Ext Spk
[ 1.259814@3] aml_snd_m8_card aml_m8_snd.48: ASoC: no source widget found for LOUTR
[ 1.267297@3] aml_snd_m8_card aml_m8_snd.48: ASoC: Failed to add route LOUTR -> direct -> Ext Spk
[ 1[ 2.394716@0] init: init.mtk.rc: 54: ignored duplicate definition of service 'mtk_supplicant'
[ 2.397730@0] init: init.mtk.rc: 78: ignored duplicate definition of service 'ap_daemon'
[ 2.405674@0] init: init.amlogic.wifi.rc: 26: ignored duplicate definition of service 'bcm_supplicant'
[ 6.065092@1] init: mount none to target failed
[ 6.128887@0] init: mount none to target failed
[ 7.516051@0] init: cannot find '/system/bin/instabootserver', disabling 'instaboot'
[ 7.520007@0] init: No charger supplies found
[ 7.528815@0] init: cannot find '/system/bin/configserver', disabling 'configserver'
[ 7.539092@0] init: cannot find '/system/bin/ctcgroupprop.sh', disabling 'ctc_group_prop'
[ 7.543293@0] init: cannot find '/system/bin/iptvserv.sh', disabling 'IptvServ'
[ 7.550027@0] init: cannot find '/system/bin/RootShellServer', disabling 'root_shell'
[ 7.556798@0] init: cannot find '/system/bin/sytr069.sh', disabling 'sy_tr069'
root@cucc_beijing:/ #
root@cucc_beijing:/ # [ 8.518297@0] init: cannot find '/system/bin/instabootserver', disabling 'instaboot'
[ 8.520835@0] android_usb: Cannot enable 'adb' (-22)[ 8.524974@1] amlkey_size() 229: ret 1
[ 8.524978@1] read_show() 922: key deviceid may not burned yet!
[ 8.565054@0] android_usb: Cannot enable 'adb' (-22)android_usb: Cannot enable 'adb' (-22)
root@cucc_beijing:/ #
root@cucc_beijing:/ #
root@cucc_beijing:/ #
------------------------------------------------------------------------------------------------------------------------------
dtb.img
------------------------------------------------------------------------------------------------------------------------------
root@cucc_beijing:/ # dd if=/dev/dtb | gzip > /storage/downloads/dtb.img.gz