Posts by dippes

Hello

I bought an Argon One M.2 for Raspberry Pi 4 which I will get in the next few days.

I currently still have my Raspi 4 in operation with an SD card but would like to switch to ssd with the new housing.

Does it still have to be configured so that it is possible to boot from USB or does it work automatically?

Hello

I have entered 4 hdmi_enable_4kp60=1 in the conf.text for my Raspi, because I have a 4k Samsung.

Question: What is the point of this although all my videos are only available in HD? Or should I switch off 4 K again in my case?

I have an old Panasonic plasma TV

When the TV is on and the Raspi 3b starts up I have picture and sound.

When the TV is switched on later, there is no picture.

I know that this works normally, I have a VDR so it doesn't matter when the TV is turned on.

Is there a workaround?

I have a Samsung RU7179 with the same remote control and a Raspi4 4G, I have an adapter between a 3m HDMI cable and the Raspi.

So it is not 100% because of the FB.

My brother-in-law with his OLED LG didn't even get sound and vision with the adapter.

What are the differences between the manufacturers and devices? CEC is standardized, right?

Solved that problem.

I had set the HDMI input of the TV to PC and after switching to Unknown it works as desired.

I wrongly thought that Raspi must be set to PC on the TV input side.

Hello

I have the picture with Kodi calibrated so that it is adapted to my TV.

Only in play mode it does not fit and cannot be corrected.

(see attachment)

Can anything be done about it?

Since I switch on my Rpi via Smart Home it is cumbersome to press the power button on the Argon housing.

Can this switch be bypassed or overridden with a GPIO command?

I bought the argon case for my Pi4 and fail to install the software.

Is the software not compatible with LibreElec?

LibreELEC (official): 9.2.1 (RPi4.arm)
Raspi-Schlafzimmer:~ #  curl https://download.argon40.com/argon1.sh | bash
  % Total    % Received % Xferd  Average Speed   Time    Time     Time  Current
                                 Dload  Upload   Total   Spent    Left  Speed
  0     0    0     0    0     0      0      0 --:--:-- --:--:-- --:--:--     0bash: syntax error: unexpected "("
 63 20128   63 12818    0     0  18657      0  0:00:01 --:--:--  0:00:01 18657
curl: (23) Failed writing body (761 != 1291)

I currently have LibreELEC 9.2 installed on my Raspi 4 B and want to upgrade to 9.2.1.

Do I have to do it manually via SD card or can I do it via Kodi interface?

Will the settings be preserved?

Hi I have a Raspi 3 B+ with an Allo Digione soundcard.

Is it possible to have HDMI and Allo Digione sound at the same time?

Thanks works now

Quote from Iridium

No idea where you got the idea to include i2c_bcm2835

I thought that was the allo digione driver

The module "i2c_bcm2835" is now loaded during system startup.

is there anything missing now?

RASPI-WOHNZIMMER:~ # lsmod
Module                  Size  Used by
hci_uart               40960  1
btbcm                  16384  1 hci_uart
serdev                 16384  1 hci_uart
bluetooth             434176  3 hci_uart,btbcm
ecdh_generic           28672  1 bluetooth
8021q                  28672  0
rc_medion_x10_or2x     16384  0
ati_remote             20480  0
brcmfmac              204800  0
rc_core                40960  3 rc_medion_x10_or2x,ati_remote
brcmutil               16384  1 brcmfmac
cfg80211              512000  1 brcmfmac
rfkill                 24576  3 bluetooth,cfg80211
bcm2835_gpiomem        16384  0
fixed                  16384  0
i2c_bcm2835            16384  0

But into which .conf the "dtoverlay=allo-digione" should be put I couldn't get it out.

I read the wiki but found no clue.

Are there no understandable instructions on how to integrate the Allo Digione into the system?

Quote

you could try adding this to your config.txt

Which config.txt is meant here?

I installed Libreelec 9.20 on my Raspi 3+.

But unfortunately my Allo Digione is not available.

Is the card not supported?

Another thread says that the card is supported, but as I see there is no driver module available.

Is there still a way to get the card?

Do you mean the addon XBMC LCDproc?

I installed that.

The desired one is now displayed.

Unfortunately, what does not work is that the display is cleared on shutdown.

Hi there

I installed Lcdproc for my Imon lcd.

The only thing that is displayed is "Welcome to LebreElec" and when exiting "Thanks for using LibreElec"

Also, the display is not cleared when shutting down.

You cannot set anything for the addon itself.

How is that supposed to be?

Found the error, the Nova-HD-S2 triggered the kernel panic, and after removing the card the shutdown works without any problems