Posts by Nebojsa
-
-
Sorry, wasn't here couple days.
So, I replaced aml_autoscript in the root directory with the attached script and run "run update".
Here is the log.
-
When enter this:
setenv maxcpus 6
run storeargs
get this, no picture, SPIDF light is on:
Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
gxm_q201_v1#setenv maxcpus 6
gxm_q201_v1#run storeargs
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[mac] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
gxm_q201_v1#
With this
setenv maxcpus 6
run bootfromsd
get this log, no picture, SPIDF off:
With this:
setenv maxcpus 4
run bootfromsd
different log, no picture, SPIDF off:
-
No, when I press recovery button and apply power get stuck at logo again.
So, when boot to Android stuck at Beelink logo, SPDIF light is on couple of seconds and then turn off.
When boot to LE/CE with correct dtb it's the same, Beelink logo and SPIDF on/off.
When boot to LE/CE with wrong p212 dtb get LE/CE logo and SPIDF stay on.
Maybe this can help something...
-
Yes, connected with HDMI to TV (without UART) and it's stuck at Beelink logo forever.
-
Yes, thanks, that worked.
Tried "store init 3" and it done it's thing, when rebooted just zeroes loop in log, so everything was deleted.
Then flashed original firmware with USB_Burning_Tool and was successful.
When boot, just Beelink logo, here is the log.
-
CoreELEC:~ # store init 3
-sh: store: not found
CoreELEC:~ # defenv
sh: defenv: not found
CoreELEC:~ # saveenv
sh: saveenv: not found
nothing works, am I doing something wrong?
-
I know that the correct dtb is gxm-q201.dtb but with it I don't get anything, it stuck somewhere in the middle of the boot process in log and no splash screen.
If GPU is broken then there should be no picture at all, or I'm mistaken?
How to try to run store init 3 in the uboot terminal?
-
Ok, thanks.
Here is CE log, is anything you can see from it?
Do You know any commands that I can use to "going to the maintance level of the box on boot up and tell it to clear all the flash area's" ?
-
Yes, I tried that also, it's the same, just CE logo...
-
I got original firmware from Beelink, flashing went ok but, like always, ended with Beelink logo forever.
That's because I tried LE but also end with LE logo.
I can ssh box with UART console but on tv is just logo (splash screen) and nothing more.
Don't know what else to try.
-
Have Beelink GT1 standard 2G/16G S912 and it's bricked. Tried to flash multiple roms but without success.
SD card metod works, got android logo and upgrading progress bar.
After couple of minutes when bar reaches 100% box boots and remain on splash screen forever.
Splash image changes regarding firmware I have flashed.
Then I tried with LE. Prepared SD card with LibreELEC USB-SD Creator, found that box will boot only with gxl_p212 DTB variants.
Tried all of them from device_trees folder but only what I get is splash screen of LE.
UART log ends with (full log in attachment):
LibreELEC:~ # [BL31]: tee size: 0
[BL31]: tee size: 0What I am doing wrong?