Posts by danilo-jlle

danilo-jlle

I see.

Is there any info or log that should help?

The interface is now on the list, but it doesn't connect.

Also, is't possible to activate it via Libreelec config (switch gets off automatically).

Code

ifconfig -a
eth0      Link encap:Ethernet  HWaddr 02:BA:39:F1:24:BB  
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:28 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

wlan0     Link encap:Ethernet  HWaddr E8:4E:06:1E:F1:9D  
          inet addr:192.168.1.158  Bcast:192.168.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:60919 errors:0 dropped:0 overruns:0 frame:0
          TX packets:52676 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:35429861 (33.7 MiB)  TX bytes:5735285 (5.4 MiB)

Display More

For now I'm using an wireless adapter, but it lags on Netflix films.

PS. I can get it to work with the Pine image and copying the dtb file for Pine+ (also editing the conf to point to that). Conversely, it works on only one microsd card (class 4). I cloned (dd image) the sdcard and write to another (class 10) and it didn't work (it boots, but no ethernet). I'm suspicious that is a sdcard issue. I'll try another sdcard with the Pine+ image and, if it doesn't work, with the image I had created.

Thanks.

danilo-jlle

Anyone has a Pine64 and can confirm the ethernet problem?

danilo-jlle

Quote from roel

According the picture: A64 with 2GB ram is a pine64+

Yeah.

I see now.

But even with the Pine64+ image I can't get etherne to work.

The results are the same.

Any idea?

Thanks in advance.

danilo-jlle

No luck with the Pine64+ image either.

Code

dmesg | grep eth
[    0.000000] psci: probing for conduit method from DT.
[   11.917939] dwmac-sun8i 1c30000.ethernet: PTP uses main clock
[   11.935933] dwmac-sun8i 1c30000.ethernet: Current syscon value is not the default 6 (expect 0)
[   11.935962] dwmac-sun8i 1c30000.ethernet: No HW DMA feature register supported
[   11.935969] dwmac-sun8i 1c30000.ethernet: RX Checksum Offload Engine supported
[   11.935976] dwmac-sun8i 1c30000.ethernet: COE Type 2
[   11.935983] dwmac-sun8i 1c30000.ethernet: TX Checksum insertion supported
[   11.935992] dwmac-sun8i 1c30000.ethernet: Normal descriptors
[   11.936000] dwmac-sun8i 1c30000.ethernet: Chain mode enabled
[   12.017213] dwmac-sun8i 1c30000.ethernet eth0: Could not attach to PHY
[   12.017230] dwmac-sun8i 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[  244.715743] dwmac-sun8i 1c30000.ethernet eth0: Could not attach to PHY
[  244.715763] dwmac-sun8i 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[  248.698940] dwmac-sun8i 1c30000.ethernet eth0: Could not attach to PHY
[  248.698962] dwmac-sun8i 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[  254.565973] dwmac-sun8i 1c30000.ethernet eth0: Could not attach to PHY
[  254.565995] dwmac-sun8i 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[  292.732837] dwmac-sun8i 1c30000.ethernet eth0: Could not attach to PHY
[  292.732858] dwmac-sun8i 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[  357.788378] dwmac-sun8i 1c30000.ethernet eth0: Could not attach to PHY
[  357.788395] dwmac-sun8i 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[  360.068862] dwmac-sun8i 1c30000.ethernet eth0: Could not attach to PHY
[  360.068883] dwmac-sun8i 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[  363.168764] dwmac-sun8i 1c30000.ethernet eth0: Could not attach to PHY
[  363.168785] dwmac-sun8i 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[  418.603254] dwmac-sun8i 1c30000.ethernet eth0: Could not attach to PHY
[  418.603274] dwmac-sun8i 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)

Display More

danilo-jlle

Hi.

I believe I did.

https://photos.app.goo.gl/wsqxmm8vb4ejszp58

Now Im in doubt if it is + or not... I bought it long ago...

I will try.

Thanks for your response.

danilo-jlle

Original post:

No ethernet connection

Hi.

Just installed the nightly version on a Pine64.

The ethernet connection doesn't work at all.

Code

dmesg | grep eth
[    0.000000] psci: probing for conduit method from DT.
[   11.454400] dwmac-sun8i 1c30000.ethernet: PTP uses main clock
[   11.455160] dwmac-sun8i 1c30000.ethernet: Current syscon value is not the default 6 (expect 0)
[   11.455185] dwmac-sun8i 1c30000.ethernet: No HW DMA feature register supported
[   11.455192] dwmac-sun8i 1c30000.ethernet: RX Checksum Offload Engine supported
[   11.455278] dwmac-sun8i 1c30000.ethernet: COE Type 2
[   11.455286] dwmac-sun8i 1c30000.ethernet: TX Checksum insertion supported
[   11.455294] dwmac-sun8i 1c30000.ethernet: Normal descriptors
[   11.455301] dwmac-sun8i 1c30000.ethernet: Chain mode enabled
[   11.533114] dwmac-sun8i 1c30000.ethernet eth0: Could not attach to PHY
[   11.533132] dwmac-sun8i 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[   11.631590] dwmac-sun8i 1c30000.ethernet: EMAC reset timeout
[   11.631915] dwmac-sun8i: probe of 1c30000.ethernet failed with error -14
[  945.260667] platform 1c30000.ethernet eth0: Could not attach to PHY
[  945.260678] platform 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[  947.460105] platform 1c30000.ethernet eth0: Could not attach to PHY
[  947.460116] platform 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[  952.926758] platform 1c30000.ethernet eth0: Could not attach to PHY
[  952.926768] platform 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[  957.026866] platform 1c30000.ethernet eth0: Could not attach to PHY
[  957.026877] platform 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[  958.560267] platform 1c30000.ethernet eth0: Could not attach to PHY
[  958.560278] platform 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[  960.443139] platform 1c30000.ethernet eth0: Could not attach to PHY
[  960.443150] platform 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[ 1066.302929] platform 1c30000.ethernet eth0: Could not attach to PHY
[ 1066.302940] platform 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[ 1154.384283] platform 1c30000.ethernet eth0: Could not attach to PHY
[ 1154.384294] platform 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[ 2214.954269] platform 1c30000.ethernet eth0: Could not attach to PHY
[ 2214.954280] platform 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)

Display More

Any idea how to solve it?

danilo-jlle · Pine64 - No ethernet connection danilo-jlle August 13, 2019 at 9:12 PM

Hi.

Just installed the nightly version on a Pine64.

The ethernet connection doesn't work at all.

It seem there are no device.

Code

dmesg | grep eth
[    0.000000] psci: probing for conduit method from DT.
[   11.454400] dwmac-sun8i 1c30000.ethernet: PTP uses main clock
[   11.455160] dwmac-sun8i 1c30000.ethernet: Current syscon value is not the default 6 (expect 0)
[   11.455185] dwmac-sun8i 1c30000.ethernet: No HW DMA feature register supported
[   11.455192] dwmac-sun8i 1c30000.ethernet: RX Checksum Offload Engine supported
[   11.455278] dwmac-sun8i 1c30000.ethernet: COE Type 2
[   11.455286] dwmac-sun8i 1c30000.ethernet: TX Checksum insertion supported
[   11.455294] dwmac-sun8i 1c30000.ethernet: Normal descriptors
[   11.455301] dwmac-sun8i 1c30000.ethernet: Chain mode enabled
[   11.533114] dwmac-sun8i 1c30000.ethernet eth0: Could not attach to PHY
[   11.533132] dwmac-sun8i 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[   11.631590] dwmac-sun8i 1c30000.ethernet: EMAC reset timeout
[   11.631915] dwmac-sun8i: probe of 1c30000.ethernet failed with error -14
[  945.260667] platform 1c30000.ethernet eth0: Could not attach to PHY
[  945.260678] platform 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[  947.460105] platform 1c30000.ethernet eth0: Could not attach to PHY
[  947.460116] platform 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[  952.926758] platform 1c30000.ethernet eth0: Could not attach to PHY
[  952.926768] platform 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[  957.026866] platform 1c30000.ethernet eth0: Could not attach to PHY
[  957.026877] platform 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[  958.560267] platform 1c30000.ethernet eth0: Could not attach to PHY
[  958.560278] platform 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[  960.443139] platform 1c30000.ethernet eth0: Could not attach to PHY
[  960.443150] platform 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[ 1066.302929] platform 1c30000.ethernet eth0: Could not attach to PHY
[ 1066.302940] platform 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[ 1154.384283] platform 1c30000.ethernet eth0: Could not attach to PHY
[ 1154.384294] platform 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[ 2214.954269] platform 1c30000.ethernet eth0: Could not attach to PHY
[ 2214.954280] platform 1c30000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)

Display More

Any idea how to solve it?

Posts by danilo-jlle

Nightly images for A64, H3, H5, H6 and R40 boards

Nightly images for A64, H3, H5, H6 and R40 boards

Nightly images for A64, H3, H5, H6 and R40 boards

Nightly images for A64, H3, H5, H6 and R40 boards

Nightly images for A64, H3, H5, H6 and R40 boards

Nightly images for A64, H3, H5, H6 and R40 boards

Pine64 - No ethernet connection