Posts by meda2019

Thank you, that is the final solution.

Yes, this latest Kodi and LibreElec systems are more agile, on the same HW, than before. That's a good job!

I have one more question:

First, the Samsung 4K TV's picture info showed me that 4K video runs at FullHD 1980x1080 /60Hz.

I went through the items in the Settings menu System - List of enabled...

and enabled 3840x2160, there was no frequency other than 30Hz or less.

1980x1080 was the option for 60Hz and below. I enabled all of these named resolutions and also the items Reduce frequency 3:2... and Enable double...

The TV still held 3840x2160 /30Hz even after rebooting.

In between, I installed apps, configured apps, did backups.

I have no idea(?) when the 3840x2160 /60Hz picture info appeared on the Samsung 4K TV.

But yes, now the TV shows 60Hz!

So I want to ask which items are important for this setting ( 3840x2160 /60Hz)?

Finally I made a new USB drive installation of LE11 Final and added entries to config.txt as recommended by the site, and cmdline.txt:

vc4.force_hotplug=1 #this cmdline parameter decided.

I could edit the files in the Linux PC before the first run on the Raspberry, it went quickly.

Thank you very much for your advice and support.

Maybe already unnecessary - I attach the log file:

hastebin

Yes. When I get to it again. Thank you

Have a nice day! I'm here with the experimental results on LE11 Final.

I have tried all the suggested procedures. The result was consistently bad. I had already performed most of them before writing the first post.

Then I focused on distroconfig.txt, it is not recommended to make changes in it. So I tested the distroconfig entries in config.txt.

Finding - the problem is with the kernel.img file: blocking kernel does not cancel the HDMI0 output but only shows a black screen. TV screen shows info 3840x2160 /30Hz.

I made an attempt to replace the kernel.img file (+md5) in LE11 with the file from LE10.

Now it shows the LE boot screen but - it says "load broken" and runs a timeout of 60sec, then it says Failured Pulse Audio. Then it reboots and the thing repeats.

I think that's the end of LE11 on a 4K Samsung Q80 TV.

EDIT:

Yeah, I'm just now seeing that next post from Da Flex. I'll try again when I can, thank you.

Thank you, I'll try this

Hello! I apologize for the quality of the translation*.

I have an unsolved problem with LE 10.95.0-1. - installation on USB stick.

On RPi4B HDMI0 to connect to Samsung 4K Q80 series 2021 TV (max 3840x2160 /60Hz).

(There is no other option Q80 than extended HDMI signal on the TV.)

When LE starts, it shows a text dump and then the TV states that RPi4 HDMI0 is off, even though LE is reachable from Kore or on LAN SW to check the run.

I plugged in a good quality 8K HDMI cable.

On the RPi4B HDMI1 at the same time the TV shows a FullHD /60Hz picture, there is no CEC function.

(If I connect this RPi4B HDMI0 to another FullHD TV/display, everything is fine.)

Parameters: hdmi_enable_4kp60=1; hdmi_enable_ekp60=1

...HDMI1 function is not affected at all, it still shows FullHD..?

No procedure posted on the forum has helped to get the TV to show the image in the GUI from HDMI0.

I used the advice from THREAD1

and also from THREAD2

In the guisettings.xml file these parameters appeared but it does not affect the problem.

Thank you for returning to the original working default GUI for RPi4 HDMI0.

Does anyone have a solution for that TV Q80?

Thank you very much.

*/Translated with http://www.DeepL.com/Translator (free version)

Thank you for your interest in this functionality.

Best regards and a nice day

Hello, I send an apology to my contribution in:

Un-US Keyboard Layout does not work with full characters

In the following posts I do not use inappropriate wording and unnecessary emphasis (shouting).

I know the value of your work and the benefits for a community of fans of LE.

I hope that reporting around the missing un-US layout USB Keyboard is a sort of future editing experience in LE.

Thank you for your great work for everything.

ONLY for PROGRAMMERS, LibreELEC Team PROFESSIONAL!!!

This post is NOT for OTHER, ONLY for LibreELEC Team PROFESSIONAL!!!

(Not FOR DONOR (Jocke.Sve), NOT for BEGINNER and other!!!)

HW: Raspberry Pi 2B, 3B; Odroid C2. (For example used AMD/Intel PC's.)

SW: System LibreELEC 8.2.5 (with Kodi 17.6)

Add HW Keyboard wireless and/other wire full 105 key Keyboard:

Logitech K120 CZ/SK, Logitech K400 Plus CZ, Rapoo E9070,

HP Classic Wired Keyboard CZ...

EXAMPLE to COMPARE:

System Raspbian Stretch with desktop (v. March 2018) on HW (present RPi 2b, 3b, Odroid c2) make input text from keyboard

with US Layoutand (switched) CZECH LAYOUT with FULL FEATURES National Characters (Key)!!!!!

Media center Kodi 17.6 on other system (example desktop Linux, Windows) make input

text from keyboard with CZECH LAYOUT with FULL FEATURES National Characters (Key)!!!!!

BUG REPORT (FORCEFUL):

System LibreELEC 8.2.5 (with Kodi 17.6) with selection the correct layout CZECH

(select national key in Setup LibreELEC and Kodi) NO PROCESSED THESE CHARACTERS!

Question together with RPi: Why Raspbian YES? Why LibreELEC NOT???

I DEMAND to REPAIR (ADD) in the NEXT version 9.0.XX

Please, no answers from not-team-LibreELEC and not-programmers. Thanks!