Posts by TwsitedElec

  • TP Link AC600 t2u usb not working

    Have tried with the new one (AC600 T2U) only. only gives the 2.4ghz network.

    Currently system gives me two options for my 2.4ghz network. If i use only the new one i cant connect to the networks to get the link uploaded.

    AC600 T2u does not even keep the 2.4ghz network connected

  • TP Link AC600 t2u usb not working

    hi.

    Thank you.

    so got the firmware now. libreelec sees the usb wifi device but fails to connect, also it is only seeing my 2.4ghz network and not the 5ghz.

    dmesg:

    [ 22.878617] mt76x0 1-4:1.0: ASIC revision: 76100002 MAC revision: 76502000

    [ 23.111514] BBP version f000f200

    [ 23.154853] mt76x0 1-4:1.0: EEPROM ver:02 fae:01

    [ 23.155107] mt76x0 1-4:1.0: EEPROM country region 01 (channels 1-13)

    [ 23.167225] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'

    [ 23.168145] usbcore: registered new interface driver mt76x0

    [ 23.204729] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready

    [ 26.238446] tg3 0000:02:00.0 eth0: Link is up at 1000 Mbps, full duplex

    [ 26.238470] tg3 0000:02:00.0 eth0: Flow control is on for TX and on for RX

    [ 26.238541] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

    [ 26.248447] 8021q: 802.1Q VLAN Support v1.8

    [ 29.041453] snd_hda_intel 0000:01:00.1: IRQ timing workaround is activated fo r card #0. Suggest a bigger bdl_pos_adj.

    [ 144.411467] wlan0: authenticate with 00:ad:24:f9:22:79

    [ 144.476830] wlan0: send auth to 00:ad:24:f9:22:79 (try 1/3)

    [ 144.478531] wlan0: authenticated

    [ 144.480964] wlan0: associate with 00:ad:24:f9:22:79 (try 1/3)

    [ 144.485172] wlan0: RX AssocResp from 00:ad:24:f9:22:79 (capab=0x411 status=0 aid=5)

    [ 144.741741] wlan0: associated

    [ 145.481966] wlan0: deauthenticated from 00:ad:24:f9:22:79 (Reason: 15=4WAY_HA NDSHAKE_TIMEOUT)

  • TP Link AC600 t2u usb not working

    Hi.

    I recently upgraded my usb wifi the AC600 T2U and my hp proliant does not recognize the new usb wifi dongle.

    Dmesg portion i think is applicable:

    [ 4228.047733] usb 2-1: new high-speed USB device number 3 using ehci-pci

    [ 4228.231488] cfg80211: Loading compiled-in X.509 certificates for regulatory database

    [ 4228.303782] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'

    [ 4228.451033] usb 2-1: reset high-speed USB device number 3 using ehci-pci

    [ 4228.606919] mt76x0 2-1:1.0: ASIC revision: 76100002 MAC revision: 76502000

    [ 4228.609885] mt76x0 2-1:1.0: Direct firmware load for mediatek/mt7610u.bin failed with error -2

    [ 4228.610470] mt76x0: probe of 2-1:1.0 failed with error -2

    [ 4228.610545] usbcore: registered new interface driver mt76x0

    Any assistance would be greatly appreciated

  • Drive mount issue after power outage

    Hi All. Not sure if this has been asked before i cant really find anything that matches my query.

    So we have these wonderful scheduled power outages here is sunny South Africa know as loadshedding.

    When a power outage occurs and we are up and running again my Libreelec Hp Proliant micro server looses a drive. Consistently it will be either my 4tb or my 6tb that does not mount. even after numerous reboot the drive refuses to mount.

    My fix is to boot gpart, (drive always shows here, no flags), run a check disk then boot back to libreelec.

    This always fixes the drive. Does LE check the drives before mounting?

    IS there a way for me to force a check before mounting?