Posts by emc02

vc4.force_hotplug=1 works on 10.0.3

Thanks!

Quote from Shazb0t

Have you tried:

vc4.inval_delay=0 vc4.cec_debug=0x100

I found that worked better for me overall.

Can confirm that this is working good for me.

Quote from emc02

I've got an "too many errors" message on starting latest librespot Version on LE 10.0.2.

I've got the same on LE 9, then made a fresh install yesterday to LE 10.0.2, librespot was working well and now the same error again.

Anyone else having this problem?

Problem solved, "ZeroConfig" was disabled

I've got an "too many errors" message on starting latest librespot Version on LE 10.0.2.

I've got the same on LE 9, then made a fresh install yesterday to LE 10.0.2, librespot was working well and now the same error again.

Anyone else having this problem?

I've updated to LE10.0.2 yesterday and the CEC-Bug is annoying...

I've now installed your testbuild and added vc4.inval_delay=3000 to cmdline.txt (2000 was not enough and turned TV back on sometimes).

I would say it now works good, but not as good as on LE9. If I turn off the TV and AVR at (nearly) the same time, the TV goes back on. If I turn off one device first and some (2-3) seconds later the other device, everything is ok.

I am using a LG TV and Denon AVR.

Thanks for your work!

(BTW: I need CEC only to turn on my TV (with kodi-send --action=CECActivateSource), because it can't be powered on over network.)

The issue seems to be fixed now with newest version of libreelec?!

I've tried something else found here: Not booting on new Raspberry Pi Model 3 B+ · Issue #350 · openhab/openhabian · GitHub

replacing the old start.elf file with the new one from a fresh image makes it better, botted 5 of 5 times. Maybe this helps?!

OK, thank you!

OK, now I've no ideas:

After testing fresh installation of raspbian and libreelec on the new Rpi3 B+ I've reinserted the old SD-Card with the (upgraded) image of libreelec and this happened:

first boot was fine => reboot failed once => and then all reboots worked without problem?!

How could that be? Is there something done with the hard- or firmware on first boot or on first dist-upgrade that is not done when upgrading the hardware and using the old image?!

I've tried several things now:

Fresh install of Libreelec => first reboot failed and then 10 of 10 reboots worked well

Fresh install of raspbian => all reboots (10 of 10) worked

So maybe it's a problem on just updating from Pi3 B to Pi3 B+ without fesh install?

Are there some (config) files that are different on these installs? It's the same image, isn't it?

Thanks for the reply.

Well as I said it was not happening each time, I would say 6 of 7, which is quite a lot

I am using another Pi3 B+ with raspbian stretch (all updates done) and having the same issue there!

I don't know where to post the issue, but I think this should be known by Raspberry devs anyway, because it's simple to find, or am I wrong?

Hi,

this is my first thread here and first I want to thank the devs for the freat work!

I've upgraded my Pi3 B to Pi3 B+ (with the same SD card and LE 8.2.4 on it) and everything works fine except reboots.

System does not boot on reboot (run from SSH or inside KODI). But cold start works well.

Is it possible that there is a problem when upgrading from B to B+, or a corrupt SD card (but cold start and everything else works fine), or is there maybe a bug?

Anyone else got this problems?

Thanks!