Posts by Sirfon

Sirfon · Wireless regulatory domain Sirfon November 3, 2017 at 5:23 PM

Many thanks both. Curiously iwlist wlan0 frequency returns:

Code

wlan0     no frequency information.

However iw phy gives:

Code

Wiphy phy0
max # scan SSIDs: 10
max scan IEs length: 2048 bytes
max # sched scan SSIDs: 0
max # match sets: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports T-DLS.
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP (00-0f-ac:4)
* CMAC (00-0f-ac:6)
Available Antennas: TX 0 RX 0
Supported interface modes:
* IBSS
* managed
* AP
* P2P-client
* P2P-GO
* P2P-device
Band 1:
Capabilities: 0x1060
HT20
Static SM Power Save
RX HT20 SGI
RX HT40 SGI
No RX STBC
Max AMSDU length: 3839 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 16 usec (0x07)
HT RX MCS rate indexes supported: 0-7
HT TX MCS rate indexes are undefined
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps (short preamble supported)
* 5.5 Mbps (short preamble supported)
* 11.0 Mbps (short preamble supported)
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 2412 MHz [1] (20.0 dBm)
* 2417 MHz [2] (20.0 dBm)
* 2422 MHz [3] (20.0 dBm)
* 2427 MHz [4] (20.0 dBm)
* 2432 MHz [5] (20.0 dBm)
* 2437 MHz [6] (20.0 dBm)
* 2442 MHz [7] (20.0 dBm)
* 2447 MHz [8] (20.0 dBm)
* 2452 MHz [9] (20.0 dBm)
* 2457 MHz [10] (20.0 dBm)
* 2462 MHz [11] (20.0 dBm)
* 2467 MHz [12] (20.0 dBm)
* 2472 MHz [13] (20.0 dBm)
Band 2:
Capabilities: 0x1060
HT20
Static SM Power Save
RX HT20 SGI
RX HT40 SGI
No RX STBC
Max AMSDU length: 3839 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 16 usec (0x07)
HT RX MCS rate indexes supported: 0-7
HT TX MCS rate indexes are undefined
VHT Capabilities (0x03800032):
Max MPDU length: 11454
Supported Channel Width: neither 160 nor 80+80
RX LDPC
short GI (80 MHz)
VHT RX MCS set:
1 streams: MCS 0-9
2 streams: not supported
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT RX highest supported: 0 Mbps
VHT TX MCS set:
1 streams: MCS 0-9
2 streams: not supported
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT TX highest supported: 0 Mbps
Bitrates (non-HT):
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 5180 MHz [36] (20.0 dBm)
* 5200 MHz [40] (20.0 dBm)
* 5220 MHz [44] (20.0 dBm)
* 5240 MHz [48] (20.0 dBm)
* 5260 MHz [52] (20.0 dBm) (no IR, radar detection)
  DFS state: usable (for 122 sec)
* 5280 MHz [56] (20.0 dBm) (no IR, radar detection)
  DFS state: usable (for 122 sec)
* 5300 MHz [60] (20.0 dBm) (no IR, radar detection)
  DFS state: usable (for 122 sec)
* 5320 MHz [64] (20.0 dBm) (no IR, radar detection)
  DFS state: usable (for 122 sec)
* 5745 MHz [149] (20.0 dBm)
* 5765 MHz [153] (20.0 dBm)
* 5785 MHz [157] (20.0 dBm)
* 5805 MHz [161] (20.0 dBm)
* 5825 MHz [165] (20.0 dBm)
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* set_bss
* join_ibss
* set_pmksa
* del_pmksa
* flush_pmksa
* remain_on_channel
* frame
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* tdls_mgmt
* tdls_oper
* start_p2p_device
* connect
* disconnect
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0xd0
* managed: 0x40 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-device: 0x40 0xd0
WoWLAN support:
* wake up on anything (device continues operating normally)
software interface modes (can always be added):
valid interface combinations:
* #{ AP } <= 2, #{ managed } <= 2, #{ P2P-client, P2P-GO } <= 2, #{ P2P-device } <= 1, #{ IBSS } <= 1,
   total <= 4, #channels <= 2
Device supports scan flush.

Display More

which indeed doesn't include channel 100. I'll try switching to one of the channels listed above. I know the hardware supports channel 100 as I could connect in Android, but until I either manage to set up a build environment and try building with the regdom included, or it is added to the build () I'll either switch channel or use 2.4GHz.

Thanks again both, and too all how develop help with Kodi/LibreElec

Sirfon · Wireless regulatory domain Sirfon November 2, 2017 at 9:13 PM

Thanks very much for the reply, and that would certainly explain not being able to set it. kszaq, is that something that could be enabled in a future build?

My access point is currently set to channel 100, which from what I can see is within the frequency range allowed by the world domain so to my untrained eye it looks like it should still work even without setting the reg domain, as you say. I'll continue hunting to see if it is something unrelated to reg domain.

Sirfon · Wireless regulatory domain Sirfon November 2, 2017 at 6:15 PM

Hi,

I'm using @kszaq's 8.2.0.1 build for S905(d) on my Mecool Ki Pro. Firstly, thank you very much to all for their hard work on this. All is working well, with the exception of being unable to connect to my 5GHz network, which works fine on the built in Android. As I see other 5G wifi networks in the network list, I suspect this is to do with available channels and regulatory domain, which seems to be confirmed by the following output on running iw reg get which returns:

Code

global
country 00: DFS-UNSET
    (2402 - 2472 @ 40), (6, 20), (N/A)
    (2457 - 2482 @ 40), (6, 20), (N/A), PASSIVE-SCAN
    (2474 - 2494 @ 20), (6, 20), (N/A), NO-OFDM, PASSIVE-SCAN
    (5170 - 5250 @ 160), (6, 20), (N/A), PASSIVE-SCAN
    (5250 - 5330 @ 160), (6, 20), (N/A), DFS, PASSIVE-SCAN
    (5490 - 5730 @ 160), (6, 20), (N/A), DFS, PASSIVE-SCAN

However running iw reg set GB makes no difference. I have also tried creating /etc/modprobe.d/cfg80211.conf which contains:

Code

options cfg80211 ieee80211_regdom=GB

But to no avail.

Dmesg just after boot returns the following: TaaP

and kodi.log is: ObIT

Does anyone have any other ideas on how I can set the regdom, or if I am barking up altogether the wrong tree?

Many thanks.